Home › Engine / Hybrid System › M15A-FXE (INTAKE / EXHAUST) › EXHAUST PIPE (for 2WD) › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093770 M15A-FXE INTAKE / EXHAUST _0442059 EXHAUST PIPE(for 2WD) A

M15A-FXE INTAKE / EXHAUST  EXHAUST PIPE(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A479420N01
2.094,1.542 2.354,1.542 false 5.385,0.438 5.792,0.438 false 1.271,1.083 1.688,1.083 false 3.26,2.51 3.677,2.51 false 3.74,1.24 3.917,1.24 3.917,1.24 4.229,1.583 false 5.667,0.781 5.927,0.781 false 1.948,1.448 2.104,1.646 0.156,0.198 10 false ● 5.188,0.313 5.552,0.677 0.365,0.365 18 false 2 1.76,0.938 2.125,1.302 0.365,0.365 18 false 1 3.75,2.385 4.115,2.75 0.365,0.365 18 false 3 3.51,1.125 3.875,1.49 0.365,0.365 18 false 4 6,0.677 6.156,0.875 0.156,0.198 10 false ● 5.688,1.323 5.844,1.521 0.156,0.198 10 false x2 5.448,1.938 5.604,2.135 0.156,0.198 10 false x2 2.656,2.24 2.833,2.417 0.177,0.177 10 false x2 3.052,2.615 3.229,2.792 0.177,0.177 10 false x2 0.813,1.677 0.99,1.854 0.177,0.177 10 false x2 1.563,1.677 1.74,1.854 0.177,0.177 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
2 TAIL EXHAUST PIPE ASSEMBLY 17430 (Click here) - -
3 NO. 2 AIR FUEL RATIO SENSOR 89467C - - -
4 FRONT EXHAUST PIPE ASSEMBLY 17410 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front exhaust pipe assembly and tail exhaust pipe assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 51447D 1.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 17430 2.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Z101186

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



a.
A479422


Hide 17410 4.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Z101186

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



a.
A479424