Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2020.08–2021.07
RM3700E _55 Steering _093027 POWER ASSIST SYSTEMS _0442429 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C123A16  IG1 Circuit Circuit Voltage Below Threshold  


DESCRIPTION

The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Return-to-normal Condition Note
C123A16 IG1 Circuit Circuit Voltage Below Threshold IG voltage is 3.0 V or less
·

EPS-IGR fuse

·

IG power source circuit

·

Power steering ECU assembly


EPS warning light: Comes on EMPS A The ECU judges the system has returned to normal or the ignition switch is turned ON again -

WIRING DIAGRAM

C320443E46
5.615,2.802 6.938,3.219 1.323,0.417 10 false Power Steering ECU Assembly 3.667,0.896 4.396,1.125 0.729,0.229 10 false EPS-IGR 5.323,0.729 5.76,1.031 0.438,0.302 10 false H1 5.323,1.917 5.677,2.135 0.354,0.219 10 false H2 5.344,0.51 5.781,0.813 0.438,0.302 10 false 1 5.667,0.719 6.104,1.021 0.438,0.302 10 false IG 5.667,1.927 6.104,2.229 0.438,0.302 10 false PGND 5.365,1.698 5.802,2 0.438,0.302 10 false 2 1.385,0.719 2.948,1.094 1.563,0.375 10 false from IGR-NO. 2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When the power steering ECU assembly has been replaced, perform Power Steering ECU Initial Setting (assist map writing).

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE)

Pre-procedure1

a.

Disconnect the H1 power steering ECU assembly connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H1)Location & Routing

Click Connector(H1)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assembly

H1-1 (IG) - Body ground Ignition switch ON 8 to 16 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE)

Pre-procedure1

a.

Disconnect the H2 power steering ECU assembly connectors.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H2)Location & Routing

Click Connector(H2)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assembly

H2-2 (PGND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR