If a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop power assist. The ECU must be replaced when there is a problem with the relays because the relays are built into the ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Return-to-normal Condition | Note |
|---|---|---|---|---|---|---|---|---|
| C155A16 | Power Steering Motor "A" Supply Voltage Circuit Voltage Below Threshold | Motor "A" PIG voltage is 3.5 V or less | ·
EPS fuse ·
PIG power source circuit ·
Power steering ECU assembly |
EPS warning light: Comes on | EMPS | A | Ignition switch ON again | - |
| C155B16 | Power Steering Motor "B" Supply Voltage Circuit Voltage Below Threshold | Motor "B" PIG voltage is 3.5 V or less | ·
EPS fuse ·
PIG power source circuit ·
Power steering ECU assembly |
EPS warning light: Comes on | EMPS | A | Ignition switch ON again | - |
When the power steering ECU assembly has been replaced, perform Power Steering ECU Initial Setting (assist map writing).
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for HV Model | A |
| for Gasoline Model | B |
A
B
Pre-procedure1
Disconnect the H2 power steering ECU assembly connectors.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H2)Location & Routingewd_type=routing;type=c;code=H2 Click Connector(H2)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assemblyewd_type=component;type=c;code=H2;pinno=1 |
||
| H2-1 (PIG) - Body ground | Ignition switch ON (READY), power assist in operation | 8 to 16 V |
Procedure2
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H2)Location & Routingewd_type=routing;type=c;code=H2 Click Connector(H2)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assemblyewd_type=component;type=c;code=H2;pinno=2 |
||
| H2-2 (PGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H2 power steering ECU assembly connectors.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H2)Location & Routingewd_type=routing;type=c;code=H2 Click Connector(H2)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assemblyewd_type=component;type=c;code=H2;pinno=1 |
||
| H2-1 (PIG) - Body ground | Engine running, power assist in operation | 8 to 16 V |
Procedure2
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H2)Location & Routingewd_type=routing;type=c;code=H2 Click Connector(H2)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assemblyewd_type=component;type=c;code=H2;pinno=2 |
||
| H2-2 (PGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG