This DTC is output when an open circuit or short occurs in the communication line between a front corner ultrasonic sensor (FL sensor) and the clearance warning ECU assembly, or when a malfunction occurs in a front corner ultrasonic sensor (FL sensor) on the front.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1AE187 | Ultrasonic Sensor (Front Left Corner) Missing Message | Front corner ultrasonic sensor (FL sensor) lost communication | ·
Front corner ultrasonic sensor (FL sensor) ·
Harness or connector ·
Clearance warning ECU assembly |
Clearance Warning | A |
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION
If a DTC is detected again after the repair, turn the ignition switch to ON and turn the TOYOTA parking assist-sensor system on, and then clear the DTC.
Initialize the front corner ultrasonic sensors (FL and FR sensors) and front center ultrasonic sensors (FLC and FRC sensors).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| C1AE187, C1AE287, C1AE387 and C1AE487 are output | B |
| C1AE287, C1AE387 and C1AE487 are output | C |
| C1AE387 and C1AE487 are output | D |
| C1AE487 is output | E |
| None of the above conditions are met | F |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE287
D
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE387
E
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE487
F
Pre-procedure1
Disconnect the O60 clearance warning ECU assembly connector.
Disconnect the B1 front corner ultrasonic sensor (FL sensor) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O60,B1)Location & Routingewd_type=routing;type=c,c;code=O60,B1 Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assemblyewd_type=component;type=c;code=O60;pinno=2,4,3 Click Connector(B1)Engine Compartment>No. 3 Engine Room Wire>Front Ultrasonic Sensor Corner LHewd_type=component;type=c;code=B1;pinno=4,5,6 |
||
| O60-2 (BOF) - B1-4 (BI) | Always | Below 1 Ω |
| O60-4 (SOF) - B1-5 (SI) | Always | Below 1 Ω |
| O60-3 (E5) - B1-6 (EI) | Always | Below 1 Ω |
| O60-2 (BOF) or B1-4 (BI) - Body ground | Always | 10 kΩ or higher |
| O60-4 (SOF) or B1-5 (SI) - Body ground | Always | 10 kΩ or higher |
| O60-3 (E5) or B1-6 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Replace the front corner ultrasonic sensor (FL sensor) with a known good one.
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| C1AE187 is output | B |
| None of the above conditions are met | C |
A
B
C