This DTC is output when an open circuit or short occurs in the communication line between a front center ultrasonic sensor (FRC sensor) and the front center ultrasonic sensor (FLC sensor), or when a malfunction occurs in a front center ultrasonic sensor (FRC sensor) on the front.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1AE387 | Ultrasonic Sensor (Front Right Center) Missing Message | Front center ultrasonic sensor (FRC sensor) lost communication | ·
Front center ultrasonic sensor (FRC sensor) ·
Harness or connector ·
Clearance warning ECU assembly |
Clearance Warning | B |
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION
If a DTC is detected again after the repair, turn the ignition switch to ON and turn the TOYOTA parking assist-sensor system on, and then clear the DTC.
If C1AE296 is output at the same time, check C1AE296 first.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE296
If DTC C1AE296 is output, perform troubleshooting for DTC C1AE296 first.
| Result | Proceed to |
|---|---|
| C1AE296 is not output | A |
| C1AE296 is output | B |
A
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE296
Initialize the front corner ultrasonic sensors (FL and FR sensors) and front center ultrasonic sensors (FLC and FRC sensors).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| C1AE187, C1AE287, C1AE387 and C1AE487 are output | B |
| C1AE287, C1AE387 and C1AE487 are output | C |
| C1AE387 and C1AE487 are output | D |
| C1AE487 is not output | E |
| None of the above conditions are met | F |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE187
C
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE287
D
E
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE487
F
Pre-procedure1
Disconnect the B2 front center ultrasonic sensor (FLC sensor) connector.
Disconnect the B3 front center ultrasonic sensor (FRC sensor) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B2,B3)Location & Routingewd_type=routing;type=c,c;code=B2,B3 Click Connector(B2)Engine Compartment>No. 3 Engine Room Wire>Front Ultrasonic Sensor Center LHewd_type=component;type=c;code=B2;pinno=1,2,3 Click Connector(B3)Engine Compartment>No. 3 Engine Room Wire>Front Ultrasonic Sensor Center RHewd_type=component;type=c;code=B3;pinno=4,5,6 |
||
| B2-1 (BO) - B3-4 (BI) | Always | Below 1 Ω |
| B2-2 (SO) - B3-5 (SI) | Always | Below 1 Ω |
| B2-3 (EO) - B3-6 (EI) | Always | Below 1 Ω |
| B2-1 (BO) or B3-4 (BI) - Body ground | Always | 10 kΩ or higher |
| B2-2 (SO) or B3-5 (SI) - Body ground | Always | 10 kΩ or higher |
| B2-3 (EO) or B3-6 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Replace the front center ultrasonic sensor (FRC sensor) with a known good one.
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| C1AE387 is output | B |
| None of the above conditions are met | C |
A
B
C