Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0442914 REAR MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  P06B31C  Drive Motor "B" Control Module Position Sensor REF Power Source Circuit Voltage Out of Range  P0A1C1F  Drive Motor "B" Control Module Circuit Intermittent  P1C2C1C  Drive Motor "B" Control Module AD Converter Circuit Voltage Out of Range  P1C2C49  Drive Motor "B" Control Module AD Converter Circuit Internal Electronic Failure  P1C611F  Drive Motor "B" Control Module Position Sensor REF Power Source Circuit Intermittent  P1C631F  Drive Motor "B" Control Module Offset Power Circuit Intermittent  P262C1C  Drive Motor "B" Control Module Offset Power Circuit Voltage Out of Range  


DESCRIPTION

The rear motor generator control ECU, which is built into the rear inverter assembly, monitors its internal operation and will store DTCs if it detects a malfunction.

If any of the following DTCs are output, replace the rear inverter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P06B31C Drive Motor "B" Control Module Position Sensor REF Power Source Circuit Voltage Out of Range Rear motor generator control ECU internal malfunction
(1 trip detection logic)
Rear hybrid motor control inverter assembly Does not come on Master Warning:
Comes on
Rear Motor Generator A
P0A1C1F Drive Motor "B" Control Module Circuit Intermittent Rear motor generator control ECU internal malfunction
(1 trip detection logic)
Rear hybrid motor control inverter assembly Does not come on Master Warning:
Comes on
Rear Motor Generator A
P1C2C1C Drive Motor "B" Control Module AD Converter Circuit Voltage Out of Range Rear motor generator control ECU internal malfunction
(1 trip detection logic)
Rear hybrid motor control inverter assembly Does not come on Master Warning:
Comes on
Rear Motor Generator A
P1C2C49 Drive Motor "B" Control Module AD Converter Circuit Internal Electronic Failure Rear motor generator control ECU internal malfunction
(1 trip detection logic)
Rear hybrid motor control inverter assembly Does not come on Master Warning:
Comes on
Rear Motor Generator A
P1C611F Drive Motor "B" Control Module Position Sensor REF Power Source Circuit Intermittent Rear motor generator control ECU internal malfunction detected when DTC P0C7A17 or P1C5E19 is stored.
(1 trip detection logic)
Rear hybrid motor control inverter assembly Does not come on Master Warning:
Does not come on
Rear Motor Generator A
P1C631F Drive Motor "B" Control Module Offset Power Circuit Intermittent Rear motor generator control ECU internal malfunction detected when DTC P0C7A17 or P1C5E19 is stored.
(1 trip detection logic)
Rear hybrid motor control inverter assembly Does not come on Master Warning:
Does not come on
Rear Motor Generator A
P262C1C Drive Motor "B" Control Module Offset Power Circuit Voltage Out of Range Rear motor generator control ECU internal malfunction
(1 trip detection logic)
Rear hybrid motor control inverter assembly Does not come on Master Warning:
Comes on
Rear Motor Generator A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NEXT

COMPLETED