Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0442914 REAR MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  P0A6912  Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Battery  P0A6914  Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Ground or Open  P0A691C  Drive Motor "B" Phase V Current(High Resolution) Circuit Voltage Out of Range  P0A691F  Drive Motor "B" Phase V Current(High Resolution) Circuit Intermittent  P0A6C12  Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Battery  P0A6C14  Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Ground or Open  P0A6C1C  Drive Motor "B" Phase W Current(High Resolution) Circuit Voltage Out of Range  P0A6C1F  Drive Motor "B" Phase W Current(High Resolution) Circuit Intermittent  


DESCRIPTION

The rear motor generator control ECU (MGR ECU), which is built into the rear inverter assembly, monitors its internal operation and will store DTCs if it detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0A6912 Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Battery Rear motor inverter phase V current sensor high resolution signal circuit (short to +B)
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Wire harness or connector


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P0A6914 Drive Motor "B" Phase V Current(High Resolution) Circuit Short to Ground or Open Rear motor inverter phase V current sensor high resolution signal circuit (short to ground or open)
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Wire harness or connector


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P0A691C Drive Motor "B" Phase V Current(High Resolution) Circuit Voltage Out of Range Rear motor inverter phase V current sensor high resolution signal circuit (out of range)
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Wire harness or connector


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P0A691F Drive Motor "B" Phase V Current(High Resolution) Circuit Intermittent Out of range detected in rear motor inverter phase V current sensor when P0C7A17 or P1C5E19 is stored.
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Wire harness or connector


Does not come on Master Warning:
Does not come on
Rear Motor Generator A
P0A6C12 Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Battery Rear motor inverter phase W current sensor high resolution signal circuit (short to +B)
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Wire harness or connector


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P0A6C14 Drive Motor "B" Phase W Current(High Resolution) Circuit Short to Ground or Open Rear motor inverter phase W current sensor high resolution signal circuit (short to ground or open)
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Wire harness or connector


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P0A6C1C Drive Motor "B" Phase W Current(High Resolution) Circuit Voltage Out of Range Rear motor inverter phase W current sensor high resolution signal circuit (out of range)
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Wire harness or connector


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P0A6C1F Drive Motor "B" Phase W Current(High Resolution) Circuit Intermittent Out of range detected in rear motor inverter phase W current sensor when P0C7A17 or P1C5E19 is stored.
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Wire harness or connector


Does not come on Master Warning:
Does not come on
Rear Motor Generator A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (REAR MOTOR GENERATOR)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Rear Motor Generator > Trouble Codes
50001 396
Result:
Result Proceed to
Only P0A6912, P0A6914, P0A691C, P0A691F, P0A6C12, P0A6C14, P0A6C1C or P0A6C1F is output A
P0A6912, P0A6914, P0A691C, P0A691F, P0A6C12, P0A6C14, P0A6C1C or P0A6C1F is output and DTCs other than the DTCs in the table below are output B
P0A6912, P0A6914, P0A691C, P0A691F, P0A6C12, P0A6C14, P0A6C1C or P0A6C1F is output and Power source circuit malfunction of Rear motor generator control system DTCs in the table below are output C


Malfunction Content System Relevant DTC
Power source circuit malfunction Rear motor generator control system P06B31C Drive Motor B" Control Module Position Sensor REF Power Source Circuit Voltage Out of Range
P262C1C Drive Motor B" Control Module Offset Power Circuit Voltage Out of Range

HINT:

P0A6912, P0A6914, P0A691C, P0A691F, P0A6C12, P0A6C14, P0A6C1C or P0A6C1F may be output as a result of the malfunctions indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

C

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>P0A4516

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR