Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0442914 REAR MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  P0A4516  Drive Motor "B" Position Sensor Circuit Voltage Below Threshold  P0A451F  Drive Motor "B" Position Sensor Circuit Intermittent  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs indicate that the resolver output signal is abnormal. The cause of this malfunction may be one of the following:


Area Main Malfunction Description
Rear Inverter Low-voltage Circuit The connectors are not connected properly
Rear traction motor assembly
·

Short circuit in the motor resolver circuit

·

Motor (MGR) internal malfunction (entry of foreign matter, etc.)


Wire harness between the resolver and rear hybrid motor control inverter assembly
·

Short circuit in the wire harness

·

The connectors are not connected properly


Inside of inverter Rear hybrid motor control inverter assembly internal circuit malfunction

DESCRIPTION

Refer to the system description for the Rear Motor Resolver Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Motor Resolver Circuit

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0A4516 Drive Motor "B" Position Sensor Circuit Voltage Below Threshold Interphase short in the rear motor generator resolver circuit:
A short circuit between signal lines of generator resolver phases is electrically detected.
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Rear traction motor assembly

·

Floor wire

·

Wire harness or connector


Does not come on Master Warning:
Comes on
Rear Motor Generator A
P0A451F Drive Motor "B" Position Sensor Circuit Intermittent A short circuit between signal lines of rear motor generator resolver phases is electrically detected when DTC P0C7A17 or P1C5E19 is stored.
(1 trip detection logic)
·

Rear hybrid motor control inverter assembly

·

Rear traction motor assembly

·

Floor wire

·

Wire harness or connector


Does not come on Master Warning:
Does not come on
Rear Motor Generator A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Turn the ignition switch to ON (READY) with the shift lever in P and wait for 5 seconds or more.

5.

Drive the vehicle forward with the shift lever in D for 5 m (16 ft.) or more.

6.

Drive the vehicle backward with the shift lever in R for 5 m (16 ft.) or more.

7.

Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.




WIRING DIAGRAM

Refer to the wiring diagram for the Rear Motor Resolver Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Motor Resolver Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > Rear Motor Generator > Trouble Codes
50001 396
Result:
Result Proceed to
Only P0A4516 or P0A451F for Rear motor generator control system is output A
P0A4516 or P0A451F is output and DTCs other than the DTCs in the table below are output B
P0A4516 or P0A451F is output and Insulation malfunction of Hybrid control system DTCs in the table below are output C
P0A4516 or P0A451F is output and Microcomputer malfunction of Motor generator control system DTCs in the table below are output D
P0A4516 or P0A451F is output and Microcomputer malfunction of Rear motor generator control system DTCs in the table below are output E
P0A4516 or P0A451F is output and Power source circuit malfunction of Rear motor generator control system DTCs in the table below are output F


Table 1
Malfunction Content System Relevant DTC
Insulation malfunction Hybrid control system P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure
P1C8049 Hybrid/EV Battery Voltage System Isolation (Rear Motor Area) Internal Electronic Failure

Table 2
Malfunction Content System Relevant DTC
Microcomputer malfunction Motor generator control system P0A1C49 Drive Motor B" Control Module Internal Electronic Failure"
P314887 Lost Communication between Drive Motor A" and "B" Missing Message"
Rear motor generator control system P1C2C1C Drive Motor B" Control Module AD Converter Circuit Voltage Out of Range
P1C2C49 Drive Motor B" Control Module AD Converter Circuit Internal Electronic Failure
P314987 Lost Communication between Drive Motor A" and "B" Missing Message
Power source circuit malfunction Rear motor generator control system P06B01C Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range
P262C1C Drive Motor B" Control Module Offset Power Circuit Voltage Out of Range

HINT:
·

P0A4516 or P0A451F may be output as a result of the malfunctions indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)

C

D

E

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM)

F

GO TO DTC CHART (REAR MOTOR GENERATOR CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A475590

Check the connection condition of the low voltage connectors of the rear hybrid motor control inverter assembly and the contact pressure of each terminal. Check the terminals for deformation, and the connector for water and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


NOTICE:

Before disconnecting the connector, confirm that it is properly connected by checking that the claws of the lock levers are engaged and that the connector cannot be pulled off.


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



Post-procedure1

a.

None.



A

3.CHECK REAR MOTOR RESOLVER CIRCUIT

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK REAR MOTOR RESOLVER CIRCUIT

NEXT

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY