Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0442914 REAR MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  P31491F  Lost Communication between Drive Motor "A" and "B" Circuit Intermittent  P314987  Lost Communication between Drive Motor "A" and "B" Missing Message  


DESCRIPTION

The rear motor generator control ECU, which is built into the rear inverter assembly, communicates with the motor generator control ECU.

The rear motor generator control ECU monitors the communication data to detect malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P31491F Lost Communication between Drive Motor "A" and "B" Circuit Intermittent Communication interruption between motor generator control ECU and rear motor generator control ECU when P0C7A17 or P1C5E19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly

·

Hybrid motor control inverter assembly

·

PCU RR relay


Does not come on Master Warning:
Does not come on
Rear Motor Generator A
P314987 Lost Communication between Drive Motor "A" and "B" Missing Message Communication interruption between motor generator control ECU and rear motor generator control ECU.
(1 trip detection logic)
·

Wire harness or connector

·

Rear hybrid motor control inverter assembly

·

Hybrid motor control inverter assembly

·

PCU RR relay


Does not come on Master Warning:
Comes on
Rear Motor Generator A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.




WIRING DIAGRAM

A459261E12
0.99,2.938 1.604,3.135 0.615,0.198 10 false +BR1 0.99,3.292 1.604,3.49 0.615,0.198 10 false +BR2 1,3.792 1.615,3.99 0.615,0.198 10 false GNR1 0.99,4.125 1.604,4.323 0.615,0.198 10 false GNR2 0.708,3.167 1.021,3.365 0.313,0.198 10 false 13 0.781,2.823 1.125,3.031 0.344,0.208 10 false 6 0.781,3.667 1.125,3.865 0.344,0.198 10 false 1 0.781,4.021 1.208,4.208 0.427,0.188 10 false 7 1.948,3.406 2.104,3.604 0.156,0.198 10 false * 2.313,3.052 2.927,3.25 0.615,0.198 10 false CARH 4.458,3.042 5.073,3.24 0.615,0.198 10 false CARH 2.333,3.521 2.948,3.719 0.615,0.198 10 false CARL 4.469,3.531 5.083,3.729 0.615,0.198 10 false CARL 5.146,3.385 5.302,3.583 0.156,0.198 10 false * 2.302,4.302 2.917,4.5 0.615,0.198 10 false DRNA 2.813,3.042 3.156,3.25 0.344,0.208 10 false 2 2.823,3.521 3.167,3.729 0.344,0.208 10 false 8 2.833,4.188 3.177,4.396 0.344,0.208 10 false 9 4.24,3.042 4.583,3.25 0.344,0.208 10 false 3 4.24,3.51 4.583,3.719 0.344,0.208 10 false 9 0.635,4.708 1.094,4.906 0.458,0.198 10 false O74 0.646,4.885 3.417,5.083 2.771,0.198 10 false Rear Hybrid Motor Control Inverter Assembly 4.406,4.708 4.865,4.906 0.458,0.198 10 false A56 4.417,4.896 7.104,5.146 2.688,0.25 10 false Hybrid Motor Control Inverter Assembly 0.167,5.458 2.094,5.688 1.927,0.229 10 false *: Approximately 120 Ω 5.979,2.938 6.594,3.135 0.615,0.198 10 false +B 5.896,3.281 6.51,3.479 0.615,0.198 10 false +B2 5.802,3.792 6.417,3.99 0.615,0.198 10 false GND1 5.792,4.135 6.406,4.333 0.615,0.198 10 false GND2 6.26,2.823 6.604,3.031 0.344,0.208 10 false 6 6.281,3.167 6.625,3.375 0.344,0.208 10 false 5 6.281,3.667 6.625,3.875 0.344,0.208 10 false 24 6.292,4.01 6.635,4.219 0.344,0.208 10 false 23 5.865,2.354 6.563,2.542 0.698,0.188 10 false PCU FR 1.833,1.26 2.531,1.448 0.698,0.188 10 false PCU RR 1.74,0.354 1.896,0.552 0.156,0.198 10 false 5 2.354,0.354 2.51,0.552 0.156,0.198 10 false 3 3.25,0.615 3.948,0.802 0.698,0.188 10 false PCU-RR 1.74,0.885 1.896,1.083 0.156,0.198 10 false 1 2.354,0.896 2.51,1.094 0.156,0.198 10 false 2 4.49,1 5.188,1.188 0.698,0.188 10 false MREL 4.438,1.646 6.302,1.969 1.865,0.323 10 false Hybrid Vehicle Control ECU 4.469,1.469 5.167,1.656 0.698,0.188 10 false H44 4.188,0.865 4.5,1.063 0.313,0.198 10 false 47

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C69
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Rear Motor Generator > Clear DTCs
50002 396
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

2.CHECK DTC OUTPUT (REAR MOTOR GENERATOR CONTROL)
2.CHECK DTC OUTPUT (REAR MOTOR GENERATOR CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Rear Motor Generator > Trouble Codes
50001 396
Result:
Result Proceed to
P31491F or P314987 is output A
P31491F or P314987 is not output B



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK RELAY (PCU RR)

B

3.CHECK RELAY (PCU RR)

Pre-procedure1

a.
A459954C01
0.75,1.5 1.427,1.771 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *1 0.563,1.375 0.875,1.531 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 PCU RR Relay


Remove the PCU RR relay from the No. 5 relay block assembly.


Procedure1

a.
A167865C15
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 PCU RR Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Output DTC
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher P31491F,P314987
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω P31491F,P314987


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the PCU RR relay.



OK

4.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY POWER SOURCE)

NG

REPLACE RELAY (PCU RR)

4.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY POWER SOURCE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


Procedure1

a.
A376643C32
0.313,1 0.719,1.26 0.406,0.26 1.292,1.229 0.917,1.5 true 1.281,1.01 0.938,0.656 true 0.104,0.146 0.417,0.302 0.313,0.156 10 false *a 0.406,1.063 0.75,1.229 0.344,0.167 10 false O74 0.552,0.531 0.99,0.729 0.438,0.198 10 false GNR1 0.573,1.531 1.01,1.729 0.438,0.198 10 false GNR2
*a Front View of Wire Harness Connector
(to Rear Hybrid Motor Control Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-1 (GNR1) - Body ground Ignition switch off Below 1 Ω P31491F,P314987
O74-7 (GNR2) - Body ground Ignition switch off Below 1 Ω P31491F,P314987


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the O74 rear hybrid motor control inverter assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE POWER SUPPLY CIRCUIT

5.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY POWER SOURCE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
A376643C33
0.313,1 0.719,1.26 0.406,0.26 2.135,1.01 2.531,0.646 true 2.135,1.229 2.531,1.5 true 0.104,0.146 0.417,0.302 0.313,0.156 10 false *a 0.406,1.063 0.75,1.229 0.344,0.167 10 false O74 2.615,0.521 3.052,0.719 0.438,0.198 10 false +BR1 2.625,1.5 3.063,1.698 0.438,0.198 10 false +BR2
*a Front View of Wire Harness Connector
(to Rear Hybrid Motor Control Inverter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-6 (+BR1) - Body ground Ignition switch ON Same as auxiliary battery voltage P31491F,P314987
O74-13 (+BR2) - Body ground Ignition switch ON Same as auxiliary battery voltage P31491F,P314987


NOTICE:

Turning the ignition switch to ON with the rear hybrid motor control inverter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction in the rear hybrid motor control inverter assembly power source circuit, inspect the following even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (Power Source Circuit)

·

Fuse condition (before and after removing fuse(s)) (Power Source Circuit)

·

Connection condition of connectors (Power Source Circuit)

·

Wire harness condition (Power Source Circuit)

·

Wire harness condition (GND circuit)



Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable to the negative (-) auxiliary battery terminal.


c.

Connect the O74 rear hybrid motor control inverter assembly connector.



OK

6.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

NG

REPAIR OR REPLACE POWER SUPPLY CIRCUIT

6.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 hybrid motor control inverter assembly connector.


c.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


Procedure1

a.
A378663C30
0.188,3.438 0.594,3.677 0.406,0.24 0.344,1.188 0.75,1.427 0.406,0.24 1.927,0.344 1.625,1.115 true 1.563,1.25 1.219,0.344 true 1.115,2.708 1.365,3.292 true 1.167,4.146 1.333,3.615 true 0.229,0.188 0.542,0.344 0.313,0.156 10 false *a 0.25,2.615 0.563,2.771 0.313,0.156 10 false *b 2,0.24 2.427,0.458 0.427,0.219 10 false CARH 0.427,1.25 0.813,1.438 0.385,0.188 10 false A56 0.25,3.479 0.615,3.646 0.365,0.167 10 false O74 0.823,0.25 1.25,0.469 0.427,0.219 10 false CARL 0.667,2.615 1.094,2.833 0.427,0.219 10 false CARH 0.99,4.188 1.417,4.406 0.427,0.219 10 false CARL
*a Front View of Wire Harness Connector
(to Hybrid Motor Control Inverter Assembly)
*b Front View of Wire Harness Connector
(to Rear Hybrid Motor Control Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-3 (CARH) - O74-2 (CARH) Ignition switch off Below 1 Ω P31491F,P314987
A56-9 (CARL) - O74-8 (CARL) Ignition switch off Below 1 Ω P31491F,P314987


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-3 (CARH) or O74-2 (CARH) - Body ground and other terminals Ignition switch off 10 kΩ or higher P31491F,P314987
A56-9 (CARL) or O74-8 (CARL) - Body ground and other terminals Ignition switch off 10 kΩ or higher P31491F,P314987



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-3 (CARH) or O74-2 (CARH) - Body ground Ignition switch ON Below 1 V P31491F,P314987
A56-9 (CARL) or O74-8 (CARL) - Body ground Ignition switch ON Below 1 V P31491F,P314987


NOTICE:

Turning the ignition switch to ON with the hybrid motor control inverter assembly connector and rear hybrid motor control inverter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable to the negative (-) auxiliary battery terminal.


c.

Connect the O74 rear hybrid motor control inverter assembly connector.


d.

Connect the A56 hybrid motor control inverter assembly connector.



OK

7.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


Procedure1

a.
A376637C19
0.427,0.99 0.833,1.229 0.406,0.24 1.99,1.021 2.5,0.729 true 2,1.26 2.573,1.604 true 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a 0.5,1.042 0.844,1.271 0.344,0.229 10 false O74 2.573,0.646 3.031,0.875 0.458,0.229 10 false CARH 2.646,1.531 3.094,1.792 0.448,0.26 10 false CARL
*a Component without harness connected
(Rear Hybrid Motor Control Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Output DTC

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-2 (CARH) - O74-8 (CARL) Ignition switch off 80 to 170 Ω P31491F,P314987


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the O74 rear hybrid motor control inverter assembly connector.



OK

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY