Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442966 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P008700  Fuel Rail / System Pressure - Too Low  


DESCRIPTION

The high-pressure direct injection fuel system consists of a spill control valve, check valve, fuel relief valve, fuel pressure sensor (for high pressure side), fuel pump assembly (for high pressure side) and fuel injector assemblies. The spill control valve adjusts the return volume of high-pressure fuel. The check valve mechanically opens and closes the path to the fuel delivery pipe. The relief valve releases the fuel back to the fuel tank if there is a malfunction in the high-pressure fuel system. The fuel pump assembly (for high pressure side) is installed to the cylinder head cover and operated by a cam installed to the end of the exhaust camshaft. Rotation of the camshaft moves the pump plunger inside the fuel pump assembly (for high pressure side) up and down, pressurizing the fuel. The pressurized fuel opens the check valve and is pumped into the fuel delivery pipe. The ECM controls the spill control valve to adjust the fuel pressure between 4.0 and 20 MPa (41 and 204 kgf/cm2, 580 and 2900 psi) and monitors signals from the fuel pressure sensor (for high pressure side) to maintain the target fuel pressure.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P008700 Fuel Rail / System Pressure - Too Low Although the ECM is not requesting the fuel pump assembly (for high pressure side) to open the spill control valve, fuel pressure decreases 5 MPa (51.0 kgf/cm2, 725 psi) from target pressure for about 10 seconds (1 trip detection logic).
·

Leak of fuel

·

Fuel pipe (fuel tank - fuel pump assembly (for high pressure side))

·

Fuel pipe (fuel pump assembly (for high pressure side) - fuel injector assembly)

·

Fuel injector assembly

·

Fuel pump assembly (for high pressure side)

·

Fuel pump (for low pressure side)

·

Fuel pressure sensor (for high pressure side)

·

Fuel system

·

ECM


Comes on Engine B SAE: P0087

MONITOR DESCRIPTION

If the fuel pressure (for high pressure side) decreases despite an increase request signal being sent to the fuel pump assembly (for high pressure side) by the ECM, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components Fuel pressure sensor (for high pressure side)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the Freeze Frame Data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Start the engine.

8.

Turn GTS on.

9.

Based on the engine speed, engine load and other conditions displayed in the Freeze Frame Data, reproduce the conditions present when the DTC was stored.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P008700.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FUEL LEAK
a.

Check around and beneath the vehicle for fuel leaks, fumes, etc.

OK:

No fuel leaks present.



Result:
Proceed to
OK
NG



OK

2.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P008700)

NG

REPAIR OR REPLACE FUEL LEAK POINT

2.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P008700)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P008700 and other DTCs are output A
P008700 is output B


HINT:

If any DTCs other than P008700 are output, troubleshoot those DTCs first.




A

GO TO DTC CHART

B

3.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
3.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?

Result:
Proceed to
YES
NO




YES

DTC CAUSED BY RUNNING OUT OF FUEL

NO

4.READ FREEZE FRAME DATA (TARGET FUEL PRESSURE (LOW) / TARGET FUEL PRESSURE 2, FUEL PRESSURE (LOW) / FUEL PRESSURE 2)
4.READ FREEZE FRAME DATA (TARGET FUEL PRESSURE (LOW) / TARGET FUEL PRESSURE 2, FUEL PRESSURE (LOW) / FUEL PRESSURE 2)

Pre-procedure1

a.

Using the GTS, check "Target Fuel Pressure (Low) / Target Fuel Pressure 2" and "Fuel Pressure (Low) / Fuel Pressure 2" in the Freeze Frame Data.

HINT:
·

Check the freeze frame data recorded when the DTC was saved and after the DTC was saved.

·

Using the freeze frame data, check the vehicle condition when the DTC was saved, such as the engine is idling while the shift position is in P, D, or N, or the vehicle is running at a constant speed or accelerating.




Procedure1

a.

Read the values displayed on the GTS.

Powertrain > Engine > DTC(P008700) > Freeze Frame Data
Tester Display
Target Fuel Pressure (Low) / Target Fuel Pressure 2
Fuel Pressure (Low) / Fuel Pressure 2
50040 372 266,267 P008700
Result:
Result Proceed to
Differences between Target Fuel Pressure (Low) / Target Fuel Pressure 2 and Fuel Pressure (Low) / Fuel Pressure 2 are below 200 kPa A
Differences between Target Fuel Pressure (Low) / Target Fuel Pressure 2 and Fuel Pressure (Low) / Fuel Pressure 2 higher than 200 kPa B



Post-procedure1

a.

None.



A

5.CHECK MISFIRE COUNT OF DIRECT INJECTION

B

5.CHECK MISFIRE COUNT OF DIRECT INJECTION

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


Procedure1

a.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
50003 372 205,1223,1224,1225
Result:
Misfire Count Proceed to
There are no misfire counts A
2 cylinders or more have misfire counts A
1 cylinder have misfire counts B



Post-procedure1

a.

None.



A

6.INSPECT FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

B

REPLACE FUEL INJECTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL INJECTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



6.INSPECT FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

Pre-procedure1

a.

Start the engine.


Procedure1

a.

Check that the fuel pressure fluctuates when the engine condition changes from idling to racing.

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265
Result:
Result Proceed to
Fuel pressure does not rise A
Fuel pressure does not fluctuate B
Fuel pressure fluctuates C



Post-procedure1

a.

None.



A

7.CHECK FUEL PUMP OPERATION (FOR LOW PRESSURE SIDE)

B

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL PRESSURE SENSOR (for High Pressure)>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



C

9.REPLACE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)
7.CHECK FUEL PUMP OPERATION (FOR LOW PRESSURE SIDE)

OK

8.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

NG

REPAIR OR REPLACE FUEL SYSTEM (FOR LOW PRESSURE SIDE)

8.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

OK

9.REPLACE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)

NG

REPAIR OR REPLACE FUEL SYSTEM

9.REPLACE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)
HINT:

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL PUMP (for High Pressure)>REMOVAL

Perform "Inspection After Repair" after replacing the fuel pump assembly (for high pressure side).

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

11.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P008700 IS OUTPUT AGAIN)
11.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P008700 IS OUTPUT AGAIN)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P008700 is output B



Post-procedure1

a.

None.



A

END

B