Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442966 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P26CA12  Engine Coolant Pump Circuit Short to Battery  


DESCRIPTION

The ECM calculates the necessary cooling amount based on the engine coolant temperature, engine speed and vehicle speed, and controls the engine water pump assembly accordingly. The engine water pump assembly controls the speed of the engine water pump assembly steplessly and optimally based on a duty cycle signal sent by the ECM, which reduces engine warm-up time, improves fuel efficiency and reduces cooling loss.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P26CA12 Engine Coolant Pump Circuit Short to Battery The operation duty ratio signal (WPO) of the engine water pump assembly is a certain value or more when the engine water pump assembly operation signal is being output (1 trip detection logic).
·

Short in engine water pump assembly (water inlet housing) circuit

·

Engine water pump assembly (water inlet housing)

·

ECM


Comes on Engine A SAE: P26CD

Related Data List
DTC No. Data List
P26CA12
·

Coolant Temperature

·

Electric Water Pump Target Speed

·

Electric Water Pump Speed



MONITOR DESCRIPTION

The ECM outputs an operation duty signal (WPO) to steplessly control the speed of the engine water pump assembly. The ECM outputs an operation duty signal (WPO) to the engine water pump assembly and monitors the actual duty signal (WPO) being output. When the actual operation duty signal (WPO) exceeds a certain value when outputting an operation duty signal (WPO) to the engine water pump assembly, the ECM detects a malfunction and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Engine water pump assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Move the shift lever to P or neutral [B].

9.

Start the engine and maintain the engine speed at 2500 rpm or more for at least 40 seconds [C].

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P26CA12.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [D] again.




WIRING DIAGRAM

A457717E02
5.781,1.521 6.177,1.688 0.396,0.167 10 false WPO 5.781,3.031 6.177,3.198 0.396,0.167 10 false WPI 5.781,4.521 6.177,4.688 0.396,0.167 10 false MREL 5.781,5.083 6.177,5.25 0.396,0.167 10 false E1 6.167,5.563 6.688,5.813 0.521,0.25 10 false ECM 6.396,4.625 6.792,4.792 0.396,0.167 10 false IC 5.396,1.615 5.75,1.792 0.354,0.177 10 false D51 5.406,3.115 5.76,3.292 0.354,0.177 10 false D51 5.396,4.615 5.75,4.792 0.354,0.177 10 false A54 5.396,5.094 5.75,5.271 0.354,0.177 10 false A54 5.458,1.417 5.813,1.594 0.354,0.177 10 false 50 5.458,2.927 5.813,3.104 0.354,0.177 10 false 51 5.427,4.438 5.781,4.615 0.354,0.177 10 false 15 5.427,4.917 5.781,5.094 0.354,0.177 10 false 10 4.635,1.521 5.031,1.688 0.396,0.167 10 false SWP 5.063,2.99 5.417,3.167 0.354,0.177 10 false 2 4.646,3.021 5.042,3.188 0.396,0.167 10 false NWP 4.594,3.646 5.063,3.823 0.469,0.177 10 false PGND 2.958,3.99 3.313,4.167 0.354,0.177 10 false D34 2.969,4.167 4.938,4.573 1.969,0.406 10 false Engine Water Pump Assembly (Water Inlet Housing) 0.615,5.115 1.74,5.417 1.125,0.302 10 false Battery 0.469,4.385 1.594,4.688 1.125,0.302 10 false BATT-MAIN NO.1 0.521,3.802 1.156,4.198 0.635,0.396 10 false EFI-MAIN NO.1 0.458,3.031 1.094,3.427 0.635,0.396 10 false EFI-MAIN NO.3 0.792,2.01 1.844,2.323 1.052,0.313 10 false EFI-MAIN NO.3 1.51,3.99 2.563,4.365 1.052,0.375 10 false EFI-MAIN NO.1 1.594,1.563 1.948,1.74 0.354,0.177 10 false 2 0.802,1.552 1.156,1.729 0.354,0.177 10 false 1 0.802,1.167 1.156,1.344 0.354,0.177 10 false 5 1.583,1.167 1.938,1.344 0.354,0.177 10 false 3 1.479,3.542 1.833,3.719 0.354,0.177 10 false 2 2.281,3.552 2.635,3.729 0.354,0.177 10 false 1 2.292,3.167 2.646,3.344 0.354,0.177 10 false 3 1.49,3.167 1.844,3.344 0.354,0.177 10 false 5 5.073,3.521 5.427,3.698 0.354,0.177 10 false 1 2.521,1.198 2.875,1.375 0.354,0.177 10 false 4 2.708,1.208 3.104,1.375 0.396,0.167 10 false +B 5.073,1.5 5.427,1.677 0.354,0.177 10 false 3 1.188,2.688 2.24,3 1.052,0.313 10 false EFI NO.2 1.365,5.604 4.417,5.917 3.052,0.313 10 false WPO: Engine water pump assembly drive duty 1.385,6.031 4.625,6.375 3.24,0.344 10 false WPI: Engine water pump assembly speed signal 3.24,2.104 4.094,2.375 0.854,0.271 10 false Drive Circuit

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING))

Pre-procedure1

a.

Disconnect the engine water pump assembly (water inlet housing) connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D34)Location & Routing

Click Connector(D34)Engine Compartment>Engine Wire>Water Inlet with Water Pump Housing Sub-Assembly

D34-3 (SWP) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

2.INSPECT ECM (INTERNAL CIRCUIT)

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING) - ECM)
2.INSPECT ECM (INTERNAL CIRCUIT)

Pre-procedure1

a.

Disconnect the engine water pump assembly (water inlet housing) connector.


Procedure1

a.

Measure the resistance while maintaining at 3000 rpm.

Powertrain > Engine > Active Test
Active Test Display
Activate the Electric Water Pump
Data List Display
Electric Water Pump
50004 372 42 437
Standard:
Tester Connection Condition Specified Condition

Click Location & Routing(D34)Location & Routing

Click Connector(D34)Engine Compartment>Engine Wire>Water Inlet with Water Pump Housing Sub-Assembly

D34-3 (SWP) - Body ground During Active Test Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the SWP terminal will be unstable during the Active Test. If the resistance fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING) - ECM)

Pre-procedure1

a.

Disconnect the engine water pump assembly (water inlet housing) connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D34,D51)Location & Routing

Click Connector(D34)Engine Compartment>Engine Wire>Water Inlet with Water Pump Housing Sub-Assembly

Click Connector(D51)Engine Compartment>Engine Wire>ECM

D34-3 (SWP) or D51-50 (WPO) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR