Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442966 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P010012  Mass or Volume Air Flow Sensor "A" Circuit Short to Battery  P010014  Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the intake air volume using the following built-in components:

·

By-pass duct (allows some of the intake air to flow past a silicon chip sensor)

·

Silicon chip sensor (uses a heater control bridge circuit and temperature sensor bridge circuit to detect the difference in the temperature of the intake air that passes the sensors positioned before and after the heater).

·

Control circuit (converts the difference in temperature into a pulse signal and performs correction)


Intake air flows past the temperature sensor (before heater), the heater, and then the temperature sensor (after heater) of the silicon chip sensor in the by-pass duct. As the intake air is warmed up when it is exposed to the heater, the temperature of the intake air as it flows past the temperature sensor (after heater) is higher than when it flows past the temperature sensor (before heater). The difference in temperature of the intake air at each temperature sensor varies depending on the velocity of the intake air that flows past the silicon chip sensor. The temperature sensor bridge circuit detects the difference in temperature and the control circuit converts it into a pulse signal and outputs it to the ECM. When the temperature detected by the temperature sensor (before heater) is higher than that detected by the temperature sensor (after heater), backflow of the intake air is detected.

The ECM calculates the intake air volume based on the pulse signal received from the mass air flow meter sub-assembly, and uses it to determine the fuel injection duration necessary for an optimal air-fuel ratio.

The heater control bridge circuit has a temperature sensor and power transistor, and maintains the temperature differential between the heater temperature and intake air temperature at a specific level.

HINT:

When DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM calculates the fuel injection duration based on the engine speed and throttle valve angle. Fail-safe mode continues until a pass condition is detected.


A431660C01
5.073,1.719 4.917,0.917 4.917,0.917 4.75,0.917 true 5.073,2.521 5,3 5,3 4.833,3 true 0.667,3 0.833,3.5 0.833,3.5 1,3.5 true 6.5,2.333 6.333,2.333 6.333,2.333 6.26,2.063 true 0.417,0.333 0.667,0.5 0.25,0.167 10 false *1 6.427,1.49 6.677,1.646 0.25,0.156 10 false *a 3.125,1.49 3.375,1.656 0.25,0.167 10 false *b 4.635,2.917 4.885,3.073 0.25,0.156 10 false *c 4.531,0.844 4.781,1.01 0.25,0.167 10 false *d 3.646,1.854 3.958,2.01 0.313,0.156 10 false *e 1.063,3.427 1.375,3.583 0.313,0.156 10 false *f 6.583,2.25 6.833,2.406 0.25,0.156 10 false *f
*1 Mass Air Flow Meter Sub-assembly - -
*a Upstream Side *b Downstream Side
*c Heater *d Temperature Distribution Without Airflow
*e Flow Rate Detection by Temperature Differential *f Intake Air


DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P010012 Mass or Volume Air Flow Sensor "A" Circuit Short to Battery The mass air flow meter sub-assembly output frequency is higher than 9.8 kHz for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on Engine A SAE: P0103
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open The mass air flow meter sub-assembly output frequency is less than 0.1 kHz for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on Engine A SAE: P0102

MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter sub-assembly, the frequency level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit and stores a DTC.

Example:

When the sensor output frequency remains less than 0.1 kHz, or higher than 9.8 kHz for 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more [A].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P010012 or P010014.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [B] again.




WIRING DIAGRAM

A402064E52
1.313,1.031 1.646,1.219 0.333,0.188 10 false VCC 1.698,0.927 1.917,1.229 0.219,0.302 10 false 4 1.406,1.719 1.771,1.979 0.365,0.26 10 false FG 1.708,1.604 1.917,1.833 0.208,0.229 10 false 3 1.333,2.49 1.646,2.688 0.313,0.198 10 false E2G 1.729,2.375 1.885,2.573 0.156,0.198 10 false 2 0.396,2.896 0.719,3.125 0.323,0.229 10 false D23 0.396,3.073 2.781,3.438 2.385,0.365 10 false Mass Air Flow Meter Sub-assembly 5.26,3.125 5.698,3.385 0.438,0.26 10 false D51 5.25,3.292 5.688,3.542 0.438,0.25 10 false ECM 4.354,0.917 4.677,1.198 0.323,0.281 10 false 78 4.625,0.917 5.188,1.208 0.563,0.292 10 false VCVG 5.615,0.698 6.073,0.896 0.458,0.198 10 false 5 V 4.281,1.604 4.594,1.802 0.313,0.198 10 false 101 4.625,1.604 4.969,1.865 0.344,0.26 10 false VG 4.365,2.385 4.667,2.635 0.302,0.25 10 false 79 4.604,2.396 5.063,2.594 0.458,0.198 10 false E2G 5.271,1.417 5.927,1.75 0.656,0.333 10 false 2.2 kΩ

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D23)Location & Routing

Click Connector(D23)Engine Compartment>Engine Wire>Intake Mass Air Flow Meter Sub-Assembly

D23-4 (VCC) - D23-2 (E2G) Ignition switch ON 4.8 to 5.2 V
D23-3 (FG) - D23-2 (E2G) Ignition switch ON 4.8 to 5.2 V



b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D23)Location & Routing

Click Connector(D23)Engine Compartment>Engine Wire>Intake Mass Air Flow Meter Sub-Assembly

D23-2 (E2G) - Body ground Ignition switch off Below 1 Ω
D23-4 (VCC) - D23-3 (FG) Ignition switch off 2.09 to 2.31 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D23,D51)Location & Routing

Click Connector(D23)Engine Compartment>Engine Wire>Intake Mass Air Flow Meter Sub-Assembly

Click Connector(D51)Engine Compartment>Engine Wire>ECM

D23-4 (VCC) - D51-78 (VCVG) Always Below 1 Ω
D23-3 (FG) - D51-101 (VG) Always Below 1 Ω
D23-2 (E2G) - D51-79 (E2G) Always Below 1 Ω
D23-4 (VCC) or D51-78 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
D23-3 (FG) or D51-101 (VG) - Body ground and other terminals Always 10 kΩ or higher
D23-2 (E2G) or D51-79 (E2G) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR