Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442967 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P136001  "A" Camshaft Position Actuator Bank 1 General Electrical Failure  


DESCRIPTION

Refer to DTC P001001.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P001001

DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P136001 "A" Camshaft Position Actuator Bank 1 General Electrical Failure While engine is running, malfunction in rotation signal (VTS) of cam timing control motor with EDU assembly is detected for 3 seconds (1 trip detection logic).
·

Cam timing control motor with EDU assembly

·

Open or short in cam timing control motor with EDU assembly circuit

·

VVT relay

·

ECM


Comes on Engine A SAE Code: P1360

Symptoms and Fail-safe Operation During Cam Timing Control Motor Malfunction
Vehicle Condition Fail-Safe
·

Engine difficult to start

·

Lack of power


The cam timing control motor with EDU assembly is operated to the most retarded position.

MONITOR DESCRIPTION

This DTC is output when a rotation signal malfunction is detected in the cam timing control motor with EDU assembly. While the engine is running, if a rotation signal (VTS) malfunction is detected, a DTC is immediately output (1 trip detection logic).

MONITOR STRATEGY

Required sensors/Components Cam timing control motor with EDU assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine [A].

10.

Idle the engine for 30 seconds or more [B].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read pending the DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P136001.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [C] again.




WIRING DIAGRAM

A457716E01
0.542,4.927 1.792,5.208 1.25,0.281 10 false Auxiliary Battery 0.365,3.896 1.438,4.094 1.073,0.198 10 false BATT-MAIN 0.49,3.198 1.094,3.531 0.604,0.333 10 false EFI-MAIN NO. 1 2.094,4.719 3.167,4.917 1.073,0.198 10 false EFI-MAIN NO. 1 2.146,3.979 2.406,4.177 0.26,0.198 10 false 5 2.927,3.99 3.188,4.188 0.26,0.198 10 false 3 2.927,4.323 3.188,4.521 0.26,0.198 10 false 1 2.146,4.323 2.406,4.521 0.26,0.198 10 false 2 2.281,3.198 3.354,3.396 1.073,0.198 10 false EFI NO. 3 2.115,0.677 2.375,0.875 0.26,0.198 10 false 5 2.115,1.146 2.375,1.344 0.26,0.198 10 false 1 2.906,0.677 3.167,0.875 0.26,0.198 10 false 3 3.521,3.74 5.167,4.125 1.646,0.385 10 false Cam Timing Control Motor with EDU Assembly 3.521,3.594 5.167,3.979 1.646,0.385 10 false D15 4.635,3.052 5.104,3.26 0.469,0.208 10 false GND 4.677,2.438 5.146,2.646 0.469,0.208 10 false VTP 4.677,1.854 5.146,2.063 0.469,0.208 10 false VTS 4.677,1.24 5.146,1.448 0.469,0.208 10 false VTD 4.667,0.698 5.135,0.906 0.469,0.208 10 false VTM 5.563,4.448 6.031,4.656 0.469,0.208 10 false A53 5.552,0.802 6.021,1.01 0.469,0.208 10 false D52 5.615,0.594 6.083,0.802 0.469,0.208 10 false 44 5.625,1.167 6.094,1.375 0.469,0.208 10 false 43 5.615,1.771 6.083,1.979 0.469,0.208 10 false 42 5.594,2.375 6.063,2.583 0.469,0.208 10 false 45 5.594,4.24 6.063,4.448 0.469,0.208 10 false 11 5.927,4.333 6.5,4.521 0.573,0.188 10 false MREL 5.969,2.427 6.448,2.604 0.479,0.177 10 false EDT1 5.969,1.865 6.521,2.052 0.552,0.188 10 false EMR1 5.948,1.25 6.427,1.448 0.479,0.198 10 false EMF1 5.948,0.677 6.51,0.865 0.563,0.188 10 false EMD1 6.521,4.448 6.875,4.615 0.354,0.167 10 false IC 6.302,5.042 6.875,5.229 0.573,0.188 10 false ECM 3.813,0.823 4.281,1.031 0.469,0.208 10 false VB1 2.917,1.156 3.177,1.354 0.26,0.198 10 false 2 5.063,0.688 5.323,0.885 0.26,0.198 10 false 4 5.052,1.24 5.313,1.438 0.26,0.198 10 false 5 5.063,1.854 5.323,2.052 0.26,0.198 10 false 6 5.063,2.427 5.323,2.625 0.26,0.198 10 false 1 5.063,2.906 5.323,3.104 0.26,0.198 10 false 3 2.417,1.573 3.094,1.771 0.677,0.198 10 false VVT 0.667,0.969 1.344,1.167 0.677,0.198 10 false VVT 3.615,0.677 3.875,0.875 0.26,0.198 10 false 2 5.583,1.365 6.052,1.573 0.469,0.208 10 false D52 5.573,1.958 6.042,2.167 0.469,0.208 10 false D52 5.552,2.563 6.021,2.771 0.469,0.208 10 false D52

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY)

Pre-procedure1

a.

Disconnect the cam timing control motor with EDU assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Engine Compartment>Engine Wire>Cam Timing Control Motor with EDU Assembly

D15-2 (VB1) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

2.CHECK HARNESS AND CONNECTOR (CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY - BODY GROUND)

NG

8.INSPECT VVT RELAY
2.CHECK HARNESS AND CONNECTOR (CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the cam timing control motor with EDU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Engine Compartment>Engine Wire>Cam Timing Control Motor with EDU Assembly

D15-3 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

3.INSPECT CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY (BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY (BODY GROUND)
A471828

a.

Check the installation condition.

1.

Check that the 3 installation bolts of the cam timing control motor with EDU assembly are tightened to the specified torque.



Standard:
Item Specified Condition
Torque 21 N*m
214 kgf*cm
15 ft.*lbf


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY - ECM)

NG

TIGHTEN TO SPECIFIED TORQUE

4.CHECK HARNESS AND CONNECTOR (CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the cam timing control motor with EDU assembly connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D15,D52)Location & Routing

Click Connector(D15)Engine Compartment>Engine Wire>Cam Timing Control Motor with EDU Assembly

Click Connector(D52)Engine Compartment>Engine Wire>ECM

D15-6 (VTS) - D52-42 (EMR1) Always Below 1 Ω
D15-6 (VTS) or D52-42 (EMR1) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

5.REPLACE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY
HINT:
·

Perform "Inspection After Repair" after replacing the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P136001 is output B



Post-procedure1

a.

None.



A

END

B

8.INSPECT VVT RELAY

OK

9.CHECK HARNESS AND CONNECTOR (VVT RELAY - CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY)

NG

REPLACE VVT RELAY

9.CHECK HARNESS AND CONNECTOR (VVT RELAY - CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY)

Pre-procedure1

a.

Remove the VVT relay from the No. 1 engine room relay block.


b.

Disconnect the cam timing control motor with EDU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Engine Compartment>Engine Wire>Cam Timing Control Motor with EDU Assembly

3 (VVT relay) - D15-2 (VB1) Always Below 1 Ω
3 (VVT relay) or D15-2 (VB1) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

10.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF VVT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF VVT RELAY)

Pre-procedure1

a.

Remove the VVT relay from the No. 1 engine room relay block.


Procedure1

a.
A459394C01
0.188,0.927 0.5,1.125 0.313,0.198 10 false *1 1.729,0.125 2.042,0.323 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 VVT Relay


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (VVT relay) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

11.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF VVT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - VVT RELAY)

11.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF VVT RELAY)

Pre-procedure1

a.

Remove the VVT relay from the No. 1 engine room relay block.


b.

Turn the ignition switch to ON.


Procedure1

a.
A459394C01
0.188,0.927 0.5,1.125 0.313,0.198 10 false *1 1.729,0.125 2.042,0.323 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 VVT Relay


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 (VVT relay) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - VVT RELAY)