Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › CAMSHAFT TIMING CONTROL MOTOR › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442034 CAMSHAFT TIMING CONTROL MOTOR A

M15A-FXE ENGINE CONTROL  CAMSHAFT TIMING CONTROL MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A459222N01
0.438,0.323 0.771,0.323 false 0.938,3.469 1.271,3.469 false 3.135,2.99 3.083,3.427 3.083,3.427 2.917,3.427 false 3.406,2.24 3.323,1.906 3.323,1.906 3.156,1.906 false 0.844,0.188 1.125,0.542 0.281,0.354 18 false 1 0.563,3.375 0.844,3.729 0.281,0.354 18 false 2 2.75,3.302 3.031,3.656 0.281,0.354 18 false 3 2.927,1.844 3.208,2.198 0.281,0.354 10 false ● 2.417,2.76 2.729,2.958 0.313,0.198 10 false x3 1.302,4.604 1.625,4.813 0.323,0.208 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
2 ENGINE WIRE - - - -
3 CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY 13090E (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during cam timing control motor with EDU assembly connector removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.


Hide 2.REMOVE ENGINE WIRE

a.
A458743


Hide 13090E 3.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

a.
A458746N01
0.698,0.083 1.063,0.396 0.365,0.313 18 true i, ii 4.083,0.042 4.344,0.344 0.26,0.302 18 true iii

i.

Disconnect the cam timing control motor with EDU assembly connector.


ii.

Remove the 3 bolts and cam timing control motor with EDU assembly from the No. 2 timing chain cover assembly.

NOTICE:

If the cam timing control motor with EDU assembly has been struck or dropped, replace it.



iii.

Remove the cam timing control motor O-ring from the No. 2 timing chain cover assembly.