Refer to DTC P003612.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P003612
Although the DTC title say O2 sensor, these DTCs relate to the air fuel ratio sensor (sensor 2).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P227118 | A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 2 Circuit Current Below Threshold | While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor (sensor 2) current is less than 7.5 mA for 0.5 seconds or more (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (sensor 2) circuit ·
Air fuel ratio sensor (sensor 2) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure ·
Fuel injector assembly ·
Fuel system ·
EGR valve assembly ·
ECM |
Comes on | Engine | B | SAE Code: P2271 |
When any of these DTCs are stored, check the air fuel ratio sensor (sensor 2) current output by entering the following menus on the GTS: Powertrain / Engine / Data List / A/F (O2) Sensor Current B1S2.
Short-term fuel trim values can also be read using the GTS.
If an air fuel ratio sensor (sensor 2) malfunction is detected, the ECM will store a DTC.
A rich air fuel mixture causes a low air fuel ratio sensor (sensor 2) current, and a lean air fuel mixture causes a high air fuel ratio sensor (sensor 2) current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor (sensor 2) current during fuel-cut and detects any abnormal current values.
If the air fuel ratio sensor (sensor 2) output is less than 7.5 mA for 0.5 seconds or more of cumulative time, the ECM stores DTC P227118 (stuck on low side).
| Required Sensors/Components (Main) | Air fuel ratio sensor (sensor 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor
Engine coolant temperature sensor Throttle position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds |
| Auxiliary battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa (abs) [11 psi (abs)] or higher |
| Time after engine start | 2 seconds or more |
| Duration of following condition | 0.5 seconds or more |
| Air fuel ratio sensor (sensor 2) current | Less than 7.5 mA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with the shift lever in P [A].
In order to keep the idle stable, turn off the A/C and all other electric loads and do not perform any shift operations.
With the engine running, drive the vehicle at approximately 75 km/h (46 mph) for 10 minutes or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
If the engine stops, further depress the accelerator pedal to restart the engine.
With the shift lever in B and the engine running, drive the vehicle at 75 km/h (46 mph), and then decelerate the vehicle by releasing the accelerator pedal for 10 seconds or more to perform the fuel-cut [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If the engine stops, further depress the accelerator pedal to restart the engine.
Repeat step [C] 2 times or more in one driving cycle.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P227118.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, drive the vehicle with the shift lever in B, and then perform step [C] again.
Refer to DTC P003612.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P003612
Inspect the fuses for circuits related to this system before performing the following procedure.
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
(Select Powertrain in Health Check and then check the time stamp data.)
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P227118 and other DTCs are output | A |
| P227118 is output | B |
If any DTCs other than P227118 are output, troubleshoot those DTCs first.
A
B
Has the vehicle run out of fuel in the past?
| Proceed to |
|---|
| YES |
| NO |
YES
NO
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Procedure1
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P227118.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P227118 is output) |
B |
Post-procedure1
None.
A
B
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Procedure1
Check the test value of the air fuel ratio sensor output (sensor 2) current during fuel-cut, referring to the Driving Pattern Detail for [C] in the Confirmation Driving Pattern.
| Tester Display |
|---|
| A/F (O2) Sensor Current B1S2 |
To measure the air fuel ratio sensor (sensor 2) current precisely, perform the fuel-cut operation for as long as possible.
If it is difficult to measure the air fuel ratio sensor (sensor 2) current, use the snapshot function of the GTS.
| Test Value | Proceed to |
|---|---|
| The value of A/F Sensor Current B1S2 is 7.5 mA or higher | A |
| None of the above conditions are met | B |
Post-procedure1
None.
A
B
Pre-procedure1
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Idle the engine for 5 minutes or more with the shift lever in P.
Procedure1
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| Coolant Temperature |
| Injection Volume |
| A/F (O2) Sensor Current B1S1 |
| A/F (O2) Sensor Current B1S2 |
Monitor the output values of the air fuel ratio sensor (sensor 1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2) displayed on the GTS.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
If the sensor output value does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| GTS Display (Sensor) | Injection Volume | Status | Current |
|---|---|---|---|
| A/F (O2) Sensor Current B1S1
(Air fuel ratio (sensor 1)) |
12.5% | Rich | Below -0.075 mA |
| -12.5% | Lean | More than 0.037 mA | |
| A/F (O2) Sensor Current B1S2
(Air fuel ratio (sensor 2)) |
12.5% | Rich | Below -0.86 mA |
| -12.5% | Lean | More than 0.33 mA |
| Status of A/F (O2) Sensor Current B1S1 | Status of A/F (O2) Sensor Current B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor (Sensor 2) Condition | Proceed to |
|---|---|---|---|
| Lean | Lean | Actual air fuel ratio lean | A |
| Rich | Rich | Actual air fuel ratio rich | A |
| Lean/Rich | Lean | Air fuel ratio sensor (sensor 2) malfunction | B |
| Lean/Rich | Rich | Air fuel ratio sensor (sensor 2) malfunction | B |
| Lean/Rich | Lean/Rich | Normal | B |
Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently more than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently more than 0.33 mA.
Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently below -0.86 mA.
Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.
Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B1S2].
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
Post-procedure1
None.
A
B
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>M15A-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks in the intake system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Check for exhaust gas leaks.
No gas leaks in exhaust system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
The A/C switch and all accessories should be off.
Procedure1
Confirm that the value of Data List item Engine Independent is "Operate" and then check the value of Intake Manifold Absolute Pressure while performing the Active Test.
| Active Test Display |
|---|
| Control the EGR Step Position |
| Data List Display |
|---|
| Intake Manifold Absolute Pressure |
| Coolant Temperature |
| EGR Step Position |
| Engine Independent |
Make sure that the value of Data List item Engine Independent is "Operate" while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
The value of Intake Manifold Absolute Pressure changes in response to the EGR step position when the value of Engine Independent is "Operate".
| - | EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| Intake Manifold Absolute Pressure
(Data List) |
(EGR valve is fully closed) | Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed |
If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).
While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Remove the EGR valve assembly.
Procedure1
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Perform All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P227118.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P227118 is output) |
B |
Post-procedure1
None.
A
B
Check the fuel lines for leaks or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>Fuel Pump Control Circuit
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
NG