| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | REAR SEAT OUTER BELT ASSEMBLY | 73360D | ( )
|
- | - |
| 2 | ROOF SIDE INNER GARNISH | 62471A | - | - | - |
| 3 | REAR SEAT OUTER BELT ASSEMBLY | 73360D | - | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 4 | DECK TRIM SIDE PANEL ASSEMBLY | 64730B | - | - | - |
| 5 | DECK TRIM SIDE COVER | 64714C | - | - | - |
| 6 | NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY | 81330 | - | - | - |
| 7 | REAR DOOR OPENING TRIM WEATHERSTRIP | 62331A | - | - | - |
| 8 | REAR DOOR INSIDE SCUFF PLATE | 67917F | - | - | - |
| 9 | REAR UNDER SIDE COVER | 76973F | - | - | - |
| 10 | REAR FLOOR FINISH PLATE | 58387B | - | - | - |
| *A | for Gasoline Model | *B | for HV Model |
| *C | LH Side | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 11 | REAR SEAT CUSHION LOCK HOOK | 72693 | - | - | - |
| 12 | BENCH TYPE REAR SEAT CUSHION ASSEMBLY | - | ( )
|
- | - |
| *A | for Gasoline Model | *B | for HV Model |
| ● | Non-reusable part | - | - |
| *A | LH Side | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
| *A | w/ Deck Board | *B | for Separate Type |
| *C | for Integrated Type | *D | w/ Cover |
Use the same procedure for the RH side and LH side.
The procedure listed below is for the RH side.
73360D
1.INSTALL REAR SEAT OUTER BELT ASSEMBLY
Engage the guides to temporarily install the rear seat outer belt assembly with the 2 bolts.
Tighten bolt (A) and then bolt (B).
Install the shoulder anchor of the rear seat outer belt assembly with the bolt.
Connect the floor anchor of the rear seat outer belt assembly with the bolt.
Check that the ELR locks.
With the rear seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.
This check should be performed with the rear seat outer belt assembly installed to the vehicle.
Remove the bolt to disconnect the floor anchor of the rear seat outer belt assembly.
Connect the pretensioner connector.
62471A
2.INSTALL ROOF SIDE INNER GARNISH
73360D
3.CONNECT REAR SEAT OUTER BELT ASSEMBLY
Connect the floor anchor of the rear seat outer belt assembly with the bolt.
Install the floor anchor plate of rear seat outer belt assembly so that a belt consecutive part faces it a vehicle ahead.
64730B
4.INSTALL DECK TRIM SIDE PANEL ASSEMBLY
64714C
5.INSTALL DECK TRIM SIDE COVER
81330
6.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)
62331A
7.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
67917F
8.INSTALL REAR DOOR SCUFF PLATE INSIDE
76973F
9.INSTALL REAR UNDER SIDE COVER (for HV Model)
58387B
10.INSTALL REAR FLOOR FINISH PLATE
72693
11.INSTALL REAR SEAT CUSHION LOCK HOOK
71349E
14.INSTALL REAR SEAT BACK HINGE COVER
73350C
15.INSTALL REAR SEAT BELT ASSEMBLY OUTER CENTER
71960B
16.INSTALL REAR SEAT HEADREST ASSEMBLY CENTER
71940A
17.INSTALL REAR SEAT HEADREST ASSEMBLY
71940A
19.INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)
64771G
20.INSTALL SPARE WHEEL COVER (w/ Cover)
58410B
21.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)
64910J
22.INSTALL TONNEAU COVER ASSEMBLY
23.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
24. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
25.PERFORM DIAGNOSTIC SYSTEM CHECK