Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Rear Inverter Low-voltage Circuit  


DESCRIPTION

The cause of this malfunction may be the low-voltage circuit.

Check whether there is an open circuit in the rear inverter +B low-voltage power source system or a problem in the communication between the front inverter and rear inverter.

Related Parts Check
Area Inspection
Rear inverter +B low-voltage power source system check Check for inverter overcurrent malfunction due to +B voltage decrease (low voltage circuit)
Communication malfunction between MG-ECU inside hybrid motor control inverter assembly and MGR-ECU inside rear hybrid motor control inverter assembly Check for inverter overcurrent malfunction due to communication malfunction.
Check for short to ground in rear inverter +B low-voltage power source system -

WIRING DIAGRAM

Refer to the wiring diagram for Rear Shut Down Signal Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Shut Down Signal Circuit

A459261E10
1.01,2.938 1.625,3.135 0.615,0.198 10 false +BR1 1.01,3.292 1.625,3.49 0.615,0.198 10 false +BR2 1.021,3.792 1.635,3.99 0.615,0.198 10 false GNR1 1.01,4.125 1.625,4.323 0.615,0.198 10 false GNR2 0.729,3.167 1.042,3.365 0.313,0.198 10 false 13 0.802,2.823 0.958,3.021 0.156,0.198 10 false 6 0.813,3.656 0.969,3.854 0.156,0.198 10 false 1 0.802,4.021 0.958,4.219 0.156,0.198 10 false 7 1.969,3.406 2.125,3.604 0.156,0.198 10 false * 2.323,3.031 2.938,3.229 0.615,0.198 10 false CARH 4.479,3.042 5.094,3.24 0.615,0.198 10 false CARH 2.333,3.5 2.948,3.698 0.615,0.198 10 false CARL 4.49,3.531 5.104,3.729 0.615,0.198 10 false CARL 5.167,3.385 5.323,3.583 0.156,0.198 10 false * 2.302,4.302 2.917,4.5 0.615,0.198 10 false DRNA 2.813,3.042 3.156,3.25 0.344,0.208 10 false 2 2.823,3.521 3.167,3.729 0.344,0.208 10 false 8 2.833,4.188 3.177,4.396 0.344,0.208 10 false 9 4.26,3.042 4.604,3.25 0.344,0.208 10 false 3 4.26,3.51 4.604,3.719 0.344,0.208 10 false 9 1,4.708 1.458,4.906 0.458,0.198 10 false O74 1,4.865 2.729,5.302 1.729,0.438 10 false Rear Hybrid Motor Control Inverter Assembly 4.427,4.708 4.885,4.917 0.458,0.208 10 false A56 4.427,4.896 6.927,5.125 2.5,0.229 10 false Hybrid Motor Control Inverter Assembly 0.167,5.458 2.198,5.646 2.031,0.188 10 false *: Approximately 120 Ω 5.969,2.938 6.583,3.135 0.615,0.198 10 false +B 5.906,3.281 6.521,3.479 0.615,0.198 10 false +B2 5.792,3.76 6.406,3.958 0.615,0.198 10 false GND1 5.792,4.135 6.406,4.333 0.615,0.198 10 false GND2 6.281,2.823 6.625,3.031 0.344,0.208 10 false 6 6.302,3.167 6.646,3.375 0.344,0.208 10 false 5 6.302,3.667 6.646,3.875 0.344,0.208 10 false 24 6.313,4.01 6.656,4.219 0.344,0.208 10 false 23 5.885,2.354 6.583,2.542 0.698,0.188 10 false PCU FR 1.833,1.26 2.531,1.448 0.698,0.188 10 false PCU RR 1.74,0.354 1.896,0.552 0.156,0.198 10 false 5 2.354,0.354 2.51,0.552 0.156,0.198 10 false 3 3.25,0.615 3.948,0.802 0.698,0.188 10 false PCU-RR 1.74,0.885 1.896,1.083 0.156,0.198 10 false 1 2.354,0.896 2.51,1.094 0.156,0.198 10 false 2 4.49,1 5.188,1.188 0.698,0.188 10 false MREL 4.438,1.646 6.302,1.969 1.865,0.323 10 false Hybrid Vehicle Control ECU 4.469,1.469 5.167,1.656 0.698,0.188 10 false H44 4.188,0.865 4.5,1.063 0.313,0.198 10 false 47

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK FUSE (PCU-RR)

Pre-procedure1

a.

Remove the PCU-RR fuse from the fusible link block assembly.


Procedure1

a.
A460287C01
1.354,1.125 1.656,0.385 1.656,0.385 1.792,0.385 true 0.198,0.177 0.51,0.333 0.313,0.156 10 false *1 1.865,0.323 2.177,0.479 0.313,0.156 10 false *2
*1 Fusible Link Block Assembly
*2 PCU-RR Fuse


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
PCU-RR fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the PCU-RR fuse.



OK

2.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY SOURCE CIRCUIT)

NG

4.CHECK RELAY (PCU RR)
2.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A376643C31
0.344,1 0.781,1.313 0.438,0.313 2.135,1.01 2.531,0.646 true 2.135,1.229 2.531,1.5 true 1.292,1.229 0.917,1.5 true 1.281,1.01 0.938,0.656 true 0.104,0.146 0.417,0.302 0.313,0.156 10 false *a 0.448,1.094 0.792,1.26 0.344,0.167 10 false O74 2.615,0.521 3.052,0.719 0.438,0.198 10 false +BR1 2.625,1.5 3.063,1.698 0.438,0.198 10 false +BR2 0.552,0.531 0.99,0.729 0.438,0.198 10 false GNR1 0.573,1.531 1.01,1.729 0.438,0.198 10 false GNR2
*a Front view of wire harness connector
(to Rear Hybrid Motor Control Inverter Assembly)


Disconnect the rear hybrid motor control inverter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-1 (GNR1) - Body ground Ignition switch off Below 1 Ω
O74-7 (GNR2) - Body ground Ignition switch off Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-6 (+BR1) - Body ground Ignition switch ON 11 to 14 V
O74-13 (+BR2) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the rear hybrid motor control inverter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable to the negative (-) auxiliary battery terminal.


c.

Reconnect the rear hybrid motor control inverter assembly connector.



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

3.CHECK HARNESS AND CONNECTOR (HYBRID MOTOR CONTROL INVERTER ASSEMBLY - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the hybrid motor control inverter assembly connector.


c.
A378663C32
0.115,3.385 0.573,3.708 0.458,0.323 0.333,1.177 0.792,1.5 0.458,0.323 2.406,1.927 1.927,1.354 true 2.417,2.594 1.885,3.323 true 2.281,0.448 1.615,1.115 true 2.615,0.708 1.615,1.219 true 0.958,2.729 1.323,3.313 true 1.031,4.094 1.344,3.615 true 0.229,0.188 0.542,0.344 0.313,0.156 10 false *a 0.25,2.615 0.563,2.771 0.313,0.156 10 false *b 2.458,1.958 2.885,2.177 0.427,0.219 10 false SDNR 0.458,1.26 0.75,1.448 0.292,0.188 10 false A56 0.24,3.49 0.635,3.667 0.396,0.177 10 false O74 2.469,2.479 2.896,2.698 0.427,0.219 10 false SDNR 2.323,0.365 2.75,0.583 0.427,0.219 10 false CARH 2.688,0.615 3.115,0.833 0.427,0.219 10 false CARL 0.51,2.635 0.938,2.854 0.427,0.219 10 false CARH 0.771,4.135 1.198,4.354 0.427,0.219 10 false CARL
*a Front view of wire harness connector
(to Hybrid Motor Control Inverter Assembly)
*b Front view of wire harness connector
(to Rear Hybrid Motor Control Inverter Assembly)


Disconnect the rear hybrid motor control inverter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-3 (CARH) - O74-2 (CARH) Ignition switch off Below 1 Ω
A56-9 (CARL) - O74-8 (CARL) Ignition switch off Below 1 Ω
A56-18 (SDNR) - O74-4 (SDNR) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-3 (CARH) or O74-2 (CARH) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A56-9 (CARL) or O74-8 (CARL) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A56-18 (SDNR) or O74-4 (SDNR) - Body ground and other terminals Ignition switch off 10 kΩ or higher



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A56,O74)Location & Routing

Click Connector(A56)Engine Compartment>Engine Room Main Wire>Hybrid Motor Control Inverter Assembly

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

A56-3 (CARH) or O74-2 (CARH) - Body ground Ignition switch ON Below 1 V
A56-9 (CARL) or O74-8 (CARL) - Body ground Ignition switch ON Below 1 V
A56-18 (SDNR) or O74-4 (SDNR) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the hybrid motor control inverter assembly connector and ECM connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable to the negative (-) auxiliary battery terminal.


c.

Reconnect the rear hybrid motor control inverter assembly connector.


d.

Reconnect the hybrid motor control inverter assembly connector.



OK

REAR INVERTER LOW-VOLTAGE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK RELAY (PCU RR)

Pre-procedure1

a.

Check the PCU RR relay for improper installation.

OK:

The relay is installed securely.


HINT:

If performing a reproduction test, turn the ignition switch to ON and gently vibrate the PCU RR relay with a finger before checking for DTCs.



b.
A460753C01
2.74,1.198 2.635,1.198 2.635,1.198 2.146,1.75 true 0.281,0.167 0.594,0.323 0.313,0.156 10 false *1 2.792,1.146 3.104,1.302 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 PCU RR Relay


Remove the PCU RR relay from the No. 5 relay block assembly.


Procedure1

a.
E034090C02
0.083,0.073 0.396,0.271 0.313,0.198 10 false *1
*1 PCU RR Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the PCU RR relay.



OK

5.CHECK HARNESS OR CONNECTOR (FUSIBLE LINK BLOCK ASSEMBLY - NO. 5 RELAY BLOCK ASSEMBLY)

NG

REPLACE PCU RR RELAY

5.CHECK HARNESS OR CONNECTOR (FUSIBLE LINK BLOCK ASSEMBLY - NO. 5 RELAY BLOCK ASSEMBLY)

Pre-procedure1

a.

Disconnect the O90 fusible link block assembly connector.


b.

Remove the PCU RR relay from the No. 5 relay block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A460752C01
1.406,0.49 1.885,0.823 0.479,0.333 0.625,0.521 0.938,0.719 0.313,0.198 10 false *a 3.552,0.125 3.865,0.323 0.313,0.198 10 false *1 3.74,1.396 4.052,1.594 0.313,0.198 10 false *2 1.531,0.594 1.844,0.792 0.313,0.198 10 false O90
*1 No. 5 Relay Block Assembly *2 PCU RR Relay Holder
*a Front view of wire harness connector
(to Fusible Link Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O90)Location & Routing

Click Connector(O90)Body>Floor Wire>Fusible Link Block Assembly

O90-2 or 3 (PCU RR relay holder) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O90 fusible link block assembly connector.


b.

Install the PCU RR relay.



OK

6.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY - PCU FUSE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY - PCU FUSE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A376643C30
0.313,0.969 0.729,1.302 0.417,0.333 2.135,1.01 2.531,0.646 true 2.135,1.229 2.531,1.5 true 0.104,0.146 0.417,0.302 0.313,0.156 10 false *a 0.406,1.063 0.896,1.302 0.49,0.24 10 false O74 2.615,0.521 3.052,0.719 0.438,0.198 10 false +BR1 2.625,1.5 3.063,1.698 0.438,0.198 10 false +BR2
*a Front view of wire harness connector
(to Rear Hybrid Motor Control Inverter Assembly)


Disconnect the rear hybrid motor control inverter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-6 (+BR1) - Body ground Ignition switch off 10 kΩ or higher
O74-13 (+BR2) - Body ground Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the rear hybrid motor control inverter assembly connector.



OK

7.REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NEXT

REPLACE FUSE (PCU-RR)

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (PCU-RR)