Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for M15A-FKS) › 2020.08–2021.07
RM3700E _52 Drivetrain _094372 DRIVE SHAFT / PROPELLER SHAFT _0444420 FRONT DRIVE SHAFT ASSEMBLY(for M15A-FKS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for M15A-FKS)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C445408N01
0.26,1.594 2.417,3.354 2.156,1.76 4.802,2.521 4.802,2.188 false 5.49,2.823 5.49,2.563 false 6.188,3.146 6.188,2.885 false 4.198,2.104 4.198,1.771 false 3.771,1.823 3.771,1.49 false 3.219,1.604 3.219,1.271 false 0.865,2.25 0.865,1.917 false 1.396,2.615 1.396,2.281 false 2.01,2.906 2.01,2.573 false 2.729,3.354 2.729,2.979 false 3.49,3.927 3.49,3.531 false 4.26,4.281 4.26,3.969 false 5.563,4.969 5.563,4.573 false 6.198,0.25 6.667,0.25 false 0.313,1.646 0.688,1.885 0.375,0.24 12 false *A 3.25,1.563 3.802,1.917 0.552,0.354 18 false 6 4.979,2.469 5.531,2.823 0.552,0.354 18 false 9 5.667,2.823 6.219,3.177 0.552,0.354 18 false 7 4.854,2.51 5.229,2.75 0.375,0.24 10 false ● 5.531,2.865 5.906,3.104 0.375,0.24 10 false ● 6.229,3.167 6.604,3.406 0.375,0.24 10 false ● 4.271,4.323 4.646,4.563 0.375,0.24 10 false ● 2.729,3.406 3.104,3.646 0.375,0.24 10 false ● 3.5,3.938 3.875,4.177 0.375,0.24 10 false ● 0.917,2.313 1.292,2.552 0.375,0.24 10 false ● 6.365,3.125 6.917,3.479 0.552,0.354 18 false 8 3.729,1.844 4.125,2.083 0.396,0.24 10 false ● 4.135,2.115 4.531,2.354 0.396,0.24 10 false *1 2.875,3.365 3.427,3.719 0.552,0.354 18 false 3 3.646,3.896 4.198,4.25 0.552,0.354 18 false 1 4.417,4.281 4.969,4.635 0.552,0.354 18 false 2 2.177,2.927 2.729,3.281 0.552,0.354 18 false 5 1.479,2.604 2.031,2.958 0.552,0.354 18 false 4 5.49,5 5.885,5.24 0.396,0.24 10 false *2 2.042,2.969 2.417,3.208 0.375,0.24 10 false ● 1.031,2.26 1.583,2.615 0.552,0.354 18 false 5 5.906,0.125 6.458,0.479 0.552,0.354 18 false 10

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT AXLE OUTBOARD JOINT BOOT - (Click here) - -
2 FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP 43447F (Click here) - -
3 FRONT AXLE OUTBOARD JOINT BOOT CLAMP 43447E (Click here) - -
4 FRONT DRIVE SHAFT DAMPER 43474D (Click here) - -
5 FRONT DRIVE SHAFT DAMPER CLAMP 43474F (Click here) - -
6 FRONT DRIVE INBOARD JOINT ASSEMBLY 43040 (Click here) - -
7 FRONT AXLE INBOARD JOINT BOOT - (Click here) - -
8 FRONT AXLE INBOARD JOINT BOOT CLAMP 43448F (Click here) - -
9 FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP 43448G (Click here) - -
10 INSPECT FRONT DRIVE SHAFT ASSEMBLY - (Click here) - -

*A for RH Side with Damper - -
*1 TRIPOD JOINT *2 FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C439734C01
6.427,0.75 6.219,0.99 false 6.865,0.969 6.74,1.125 false 5.938,0.583 5.656,0.896 false 5.458,0.656 5.177,0.969 false 0.719,0.302 1,0.656 0.281,0.354 18 false i 4.042,0.229 4.323,0.583 0.281,0.354 18 false ii 4.052,2.167 4.333,2.521 0.281,0.354 18 false iv 0.677,2.177 0.958,2.531 0.281,0.354 18 false iii 5.5,0.563 5.813,0.719 0.313,0.156 10 false *1 5.979,0.521 6.292,0.677 0.313,0.156 10 false *2 6.469,0.656 6.781,0.813 0.313,0.156 10 false *3 6.885,0.865 7.073,1.031 0.188,0.167 10 false *4
*1 Front Drive Outboard Joint Shaft Assembly *2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot *4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side
V100137

Grease - -


i.

Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


ii.

Install new parts to the front drive outboard joint shaft assembly in the following order:

1. Front No. 2 axle outboard joint boot clamp

2. Front axle outboard joint boot

3. Front axle outboard joint boot clamp


iii.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:

116 to 126 g (4.09 to 4.44 oz)



iv.

Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.





Hide 43447F 2.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

Z101186

CAUTION:
C331975

·

Wear protective gloves when installing the front No. 2 axle outboard joint boot clamp.

·

If protective gloves are not worn, injuries may occur.




a.
C445409C01
2.969,1.083 3.281,0.938 false 3.948,1.208 4.354,1.208 false 3.854,1.76 4.26,1.76 false 0.458,0.125 0.74,0.479 0.281,0.354 18 false i 2.792,1.052 3.083,1.26 0.292,0.208 10 false *b 4.438,1.135 4.729,1.344 0.292,0.208 10 false *a 3.625,1.656 3.917,1.865 0.292,0.208 10 false *c
*a Fulcrum Point *b Lever Push Position
*c Band Support Position - -


i.

Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.





b.
C445410C01
3.604,1.052 3.135,1.406 3.135,1.406 3.708,1.042 true 2.083,1.49 1.594,1.49 true 1.958,2.281 1.688,2.281 1.688,2.281 1.448,1.906 true 5.927,2.229 5.646,1.938 5.646,1.938 5.49,1.938 true 3.823,0.292 4.135,0.448 0.313,0.156 10 false *a 4.104,1.302 4.417,1.458 0.313,0.156 10 false *b 5.24,0.583 5.552,0.74 0.313,0.156 10 false *c 2.979,1.354 3.292,1.51 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.417 1.74,1.573 0.313,0.156 10 false *d 2.01,2.219 2.323,2.375 0.313,0.156 10 false *e 5.281,1.875 5.594,2.031 0.313,0.156 10 false *d 0.448,0.083 0.729,0.438 0.281,0.354 18 false i
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


i.

As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

NOTICE:
·

Do not damage the deflector.

·

Make sure that the outboard joint is in direct contact with the work surface.





c.
C445411C01
3.708,3.031 2.896,3.531 2.896,3.531 3.51,2.958 true 0.448,0.094 0.729,0.448 0.281,0.354 18 false i 2.719,3.5 3.031,3.698 0.313,0.198 10 false *a
*a Buckle - -


i.

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle outboard joint boot.





Hide 43447E 3.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

Z101186

CAUTION:
C331975

·

Wear protective gloves when installing the front No. 2 axle outboard joint boot clamp.

·

If protective gloves are not worn, injuries may occur.




a.
C445412C02
5.281,5.125 4.656,5.552 4.656,5.552 5.021,5.104 true 4.469,5.49 4.781,5.688 0.313,0.198 10 false *b 0.49,3.979 0.802,4.323 0.313,0.344 18 false iii 3.917,4.021 4.25,4.333 0.333,0.313 18 false iii 4,1.771 4.333,2.083 0.333,0.313 18 false ii 0.5,1.698 0.833,2.01 0.333,0.313 18 false ii 1.948,0.177 2.281,0.49 0.333,0.313 18 false i 2.427,2.344 2.74,2.542 0.313,0.198 10 false *a
*a Place the tip near the center of the lever *b Buckle


i.

Install the front axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and the lever for any deformation before folding back the lever.




ii.

Using water pump pliers, pinch the front axle outboard joint boot clamp to temporarily secure it.

NOTICE:

Do not damage the front axle outboard joint boot.



iii.

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and groove to make the clearances between the buckle edge and lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle outboard joint boot.





Hide 43474D 4.INSTALL FRONT DRIVE SHAFT DAMPER (for RH Side with Damper)

a.
C445413C01
2.844,1.406 2.844,1.073 false 2.354,1.365 2.354,1.031 false 3.323,1.375 3.323,1.042 false 0.448,0.063 1.823,0.417 1.375,0.354 18 false i, ii 2.76,1.438 3.073,1.635 0.313,0.198 10 false *1 2.271,1.396 2.583,1.594 0.313,0.198 10 false *2 3.24,1.406 3.552,1.604 0.313,0.198 10 false *2 3.479,0.188 3.792,0.385 0.313,0.198 10 false A
*1 Front Drive Shaft Damper *2 Front Drive Shaft Damper Clamp


i.

Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.


ii.

Set the dimension (A) as specified below.

Dimension (A):

461.6 to 465.6 mm (1.51 to 1.53 ft.)




Hide 43474F 5.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side with Damper)

a.
C445405C02
2.469,1.5 2.677,1.563 2.677,1.563 2.896,1.458 false 0.427,0.083 1.083,0.417 0.656,0.333 18 false i, ii 2.615,1.583 2.813,1.781 0.198,0.198 10 false *a
*a Claw - -


i.

Install the 2 front drive shaft damper clamps to the front drive shaft damper.

NOTICE:

Be sure to install the clamps in the correct position.



ii.

Using needle-nose pliers, engage each claw to install the 2 front drive shaft damper clamps as shown in the illustration.

NOTICE:
·

Be sure to install the clamps in the correct position.

·

Do not damage the front drive shaft damper.

·

Do not damage the claws.





Hide 43040 6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C445414C01
4.938,1.552 5.823,1.594 5.823,1.594 5.323,1.333 true 3.146,4.979 2.406,4.813 2.406,4.813 3.479,4.625 true 1.052,1.542 1.052,1.292 false 1.875,1.771 1.875,1.521 false 2.521,1.833 2.521,1.583 false 2.885,1.49 2.885,1.24 false 0.49,0.208 1.042,0.531 0.552,0.323 18 false i, ii 5.25,0.198 5.802,0.521 0.552,0.323 18 false iii, iv 0.5,2 1.052,2.323 0.552,0.323 18 false v 4.281,2 4.833,2.323 0.552,0.323 18 false vi 2.594,4.125 3.146,4.448 0.552,0.323 18 false vii 5.865,2.01 6.417,2.333 0.552,0.323 18 false vi 5.896,1.542 6.448,1.865 0.552,0.323 10 false *b 2.208,4.74 2.76,5.063 0.552,0.323 10 false *b 0.979,1.563 1.531,1.885 0.552,0.323 10 false *1 1.813,1.792 2.365,2.115 0.552,0.323 10 false *2 2.458,1.854 3.01,2.177 0.552,0.323 10 false *3 2.813,1.531 3.365,1.854 0.552,0.323 10 false *a
*1 Front Axle Inboard Joint Boot Clamp *2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp - -
*a Protective Tape *b Matchmark
V100135

Outboard Joint Side
V100136

Inboard Joint Side
V100137

Grease - -


i.

Install new parts to the front drive outboard joint shaft assembly in the following order:

1. Front axle inboard joint boot clamp

2. Front axle inboard joint boot

3. Front No. 2 axle inboard joint boot clamp


ii.

Remove the protective tape.


iii.

Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



iv.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Be sure to install the tripod joint in the correct direction.




v.

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


vi.

Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard Grease Capacity:

127 to 137 g (4.48 to 4.83 oz)



vii.

Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.



Hide 7.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.
C445415N01
0.479,0.104 0.771,0.417 0.292,0.313 18 false i

i.

Install the front axle inboard joint boot to the front drive inboard joint assembly.

NOTICE:
·

Keep the grooves free of grease.

·

Keep the inside of the front axle inboard joint boot free of foreign matter.





Hide 43448F 8.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

Z101186

CAUTION:
C331975

·

Wear protective gloves when installing the front No. 2 axle outboard joint boot clamp.

·

If protective gloves are not worn, injuries may occur.




a.
C445412C03
5.281,5.125 4.656,5.552 4.656,5.552 5.021,5.104 true 4.469,5.49 4.781,5.688 0.313,0.198 10 false *b 0.49,3.979 0.802,4.323 0.313,0.344 18 false iii 3.917,4.021 4.25,4.333 0.333,0.313 18 false iii 4,1.771 4.333,2.083 0.333,0.313 18 false ii 0.5,1.698 0.833,2.01 0.333,0.313 18 false ii 1.948,0.177 2.281,0.49 0.333,0.313 18 false i 2.427,2.344 2.74,2.542 0.313,0.198 10 false *a
*a Place the tip near the center of the lever *b Buckle


i.

Install the front axle inboard joint boot clamp to the front axle inboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and the lever for any deformation before folding back the lever.




ii.

Using water pump pliers, pinch the front axle inboard joint boot clamp to temporarily secure it.

NOTICE:

Do not damage the front axle inboard joint boot.



iii.

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and groove to make the clearances between the buckle edge and lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle inboard joint boot.





Hide 43448G 9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.
C445416N01
2.531,2.875 2.948,2.458 true 5.74,2.646 6.833,2.885 true 3.448,1.281 3.604,1.479 0.156,0.198 10 false A 2.99,2.385 3.448,2.583 0.458,0.198 10 false SST 6.875,2.833 7.156,3.031 0.281,0.198 10 false SST 0.385,1.938 1.677,2.25 1.292,0.313 18 false iii, iv, v, vi 3.927,2.177 4.229,2.5 0.302,0.323 18 false vii 1.917,0.052 2.375,0.375 0.458,0.323 18 false i, ii

i.

Adjust dimension (A) until it is within the specified length.

Dimension (A):
for LH Side 622.2 to 632.2 cm (2.04 to 2.07 ft.)
for RH Side 834.1 to 844.1 mm (2.74 to 2.77 ft.)



ii.

While keeping dimension (A) within the specified length, equalize the pressure within the inboard joint with atmospheric pressure by slightly lifting the front axle inboard joint from the front drive inboard joint assembly.


iii.

Install the front No. 2 axle inboard joint boot clamp to the front axle inboard joint boot.


iv.

Place SST onto the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


v.

Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.

NOTICE:

Do not tighten SST so much that the gap of the clamp disappears completely.



vi.

Remove SST.


vii.

Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

Below 1.5 mm (0.0590 in.)


If the clearance is not as specified, retighten SST.