The power distribution box assembly controls the instrument panel illuminations.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1
*1: w/ Entry and Start System
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Input Signal | Panel light input condition | OFF or ON | OFF: Light control switch not in tail position
ON: Light control switch in tail position |
- |
| Tester Display |
|---|
| Panel Light Input Signal |
The GTS display changes.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K12 outer mirror switch assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K5 multiplex network master switch assembly connector.
Connect the GTS to the DLC3.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Disconnect the H47 auto high beam switch connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H49 headlight leveling switch connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Panoramic View Monitor System) | B |
| NG (w/o Panoramic View Monitor System) | C |
A
B
C
Disconnect the H22 panoramic view monitor switch connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SWITCH>REMOVAL
NG
Disconnect the H66 indicator light wire sub-assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H18 combination switch assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H140 electric parking brake switch assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for AWD | A |
| for 2WD | B |
A
B
Disconnect the H133 downhill assist control switch connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H134 No. 2 combination switch assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Seat Heater | A |
| w/o Seat Heater | B |
A
B
Disconnect the H52 seat heater switch LH connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H50 seat heater switch RH connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Automatic Air Conditioning System | A |
| w/ Manual Air Conditioning System | B |
A
B
Disconnect the H31 air conditioning control assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H56 No. 1 heater control sub-assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H33 No. 2 heater control sub-assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H26 No. 3 heater control sub-assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H60 spiral cable sub-assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the z2 steering pad switch assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H59 hazard warning signal switch assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Power Back Door | A |
| w/o Power Back Door | B |
A
B
Disconnect the H132 power back door control switch connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Turn the light control switch to the TAIL position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Panel Light Fuse Shut Off Status | Panel Light Fuse condition | OFF or ON | OFF: Fuse not shut off
ON: Fuse shut off |
- |
| Tester Display |
|---|
| Panel Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K5 multiplex network master switch assembly connector.
Disconnect the K12 outer mirror switch assembly connector.
Disconnect the H47 auto high beam switch connector.
Disconnect the H49 headlight leveling switch connector.
Disconnect the H22 panoramic view monitor switch connector. (w/ Panoramic View Monitor System)
Disconnect the H66 indicator light wire sub-assembly connector.
Disconnect the H18 combination switch assembly connector.
Disconnect the H140 electric parking brake switch assembly connector.
Disconnect the H133 downhill assist control switch connector. (for AWD)
Disconnect the H134 No. 2 combination switch assembly connector. (for AWD)
Disconnect the H52 seat heater switch LH connector. (w/ Seat Heater System)
Disconnect the H50 seat heater switch RH connector. (w/ Seat Heater System)
Disconnect the H31 air conditioning control assembly connector. (for Automatic Air Conditioning System)
Disconnect the H56 No. 1 heater control sub-assembly connector. (for Manual Air Conditioning System)
Disconnect the H33 No. 2 heater control sub-assembly connector. (for Manual Air Conditioning System)
Disconnect the H26 No. 3 heater control sub-assembly connector. (for Manual Air Conditioning System)
Disconnect the z2 steering pad switch assembly connector.
Disconnect the H60 spiral cable sub-assembly connector.
Disconnect the H59 hazard warning signal switch assembly connector.
Disconnect the H132 power back door control switch connector. (w/ Power Back Door)
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4E and 4C power distribution box assembly connectors.
Measure the resistance according to the value(s) in the table below.
*1: w/ Panoramic View Monitor System
*2: for AWD
*3: w/ Seat Heater System
*4: for Automatic Air Conditioning System
*5: for Manual Air Conditioning System
| Proceed to |
|---|
| OK |
| NG |
OK
NG