|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
MP grease |
|
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
| ★ | Precoated part | - | - |
| *1 | BUTYL TAPE | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
MP grease | - | - |
Use the same procedure for the LH side and RH side.
The following procedure is for the RH side.
67837C
1.INSTALL REAR DOOR DUST PROOF SEAL
|
|
75077
2.INSTALL REAR DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY
75873
3.INSTALL QUARTER PANEL WHEEL OPENING MOULDING
67887F
4.INSTALL NO. 2 REAR DOOR WEATHERSTRIP
67871
5.INSTALL REAR DOOR WEATHERSTRIP
68630
6.INSTALL REAR DOOR CHECK ASSEMBLY
| *A | When reusing a bolt. | - | - |
| *a | Bolt A | *b | Bolt B |
Clean the bolt hole in the vehicle body.
Clean the threads of the bolt A.
Apply adhesive to the threads of the bolt A.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the rear door check assembly with the bolt A and 2 bolts B.
7. REPAIR INSTRUCTION
75923C
8.INSTALL NO. 2 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Rear Door)>INSTALLATION
68180C
9.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>INSTALLATION
69203A
10.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
|
MP grease |
|
Install in this Direction |
Apply MP grease to the sliding parts on the rear door outside handle frame sub-assembly.
Engage the guides to install the rear door outside handle frame sub-assembly as shown in the illustration.
Using a T30 "TORX" socket wrench, tighten the screw.
69242G
11.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD
69241G
12.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD
69227J
13.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Engage the claws to install the rear door outside handle cover.
Using a T30 "TORX" socket wrench, tighten the screw.
69210
14.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
69318D
15.INSTALL DOOR LOCK WIRING HARNESS SEAL
69050A
16.INSTALL REAR DOOR LOCK ASSEMBLY
69803
17.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
|
MP grease | - | - |
Connect the connector.
Apply MP grease to the sliding parts of the rear door window regulator assembly.
Install the rear door window regulator assembly with the 6 nuts.
Engage the clamp.
67447C
18.INSTALL REAR DOOR WINDOW GUIDE PLATE LOWER
68011
19.INSTALL REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY
|
Install in this Direction | - | - |
Install the rear door quarter window glass sub-assembly as shown in the illustration.
Install the rear door quarter window glass sub-assembly with the 3 bolts.
68103
20.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Connect the rear power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the rear door glass sub-assembly so that the door glass bolt holes can be seen.
|
Install in this Direction | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the rear power window regulator switch assembly.
Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.
Be careful not to damage the rear door glass sub-assembly.
Install the rear door glass sub-assembly with the 2 bolts.
68142C
21.INSTALL REAR DOOR GLASS RUN
67841E
22.INSTALL REAR DOOR SERVICE HOLE COVER
| *a | Reference Point |
|
Butyl Tape |
Apply new butyl tape to the rear door panel.
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and wire harness through a new rear door service hole cover.
Install the rear door service hole cover according to the reference points on the rear door panel.
Securely install the rear door service hole cover preventing wrinkles and air bubbles.
86160B
23.INSTALL REAR SPEAKER ASSEMBLY
68198
24.INSTALL REAR DOOR BELT REAR SEAL
Install the rear door belt rear seal to the rear door glass inner weatherstrip.
68196B
25.INSTALL REAR DOOR BELT FRONT SEAL
68173B
26.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP
Install the rear door glass weatherstrip inner with the rear door rear belt seal and rear door front belt seal.
69283A
27.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
69205A
28.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
67603
29.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
|
Install in this Direction | - | - |
30.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL
31.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
32. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
33.INITIALIZE POWER WINDOW CONTROL SYSTEM
34.INSPECT POWER WINDOW OPERATION