When the electric parking brake switch is pulled, a lock request signal is sent from the skid control ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch is pushed, a release request signal is sent from the skid control ECU (brake actuator assembly) to the parking brake actuator assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| C060962 | Electric Parking Brake Switch Signal Compare Failure | ·
Parking brake switch open or short circuit is detected for 1 seconds or more ·
Parking brake switch stuck malfunction |
·
Electric parking brake switch (electric parking brake switch assembly) ·
Wire harness or connector ·
Skid control ECU (brake actuator assembly) |
DTC stored | Brake/EPB | A | An electric parking brake system malfunction is displayed on the multi-information display. |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | - | - | - | - |
| Malfunction Status | Parking brake switch open circuit is detected | ○ | - | - |
| Parking brake switch short circuit is detected | - | ○ | - | |
| Parking brake switch stuck malfunction | - | - | ○ | |
| Detection Time | 1 second or more | 1 second or more | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
If the electric parking brake switch is held near the lock position but not fully in the lock position for 1 second or more, a DTC may be stored due to one of the two contacts being ON while the other is OFF. (This is not a system malfunction.)
The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.
OK
NG
Pre-procedure1
Disconnect the H140 electric parking brake switch (electric parking brake switch assembly) connector.
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A94,H140)Location & Routingewd_type=routing;type=c,c;code=A94,H140 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=36,31,41,39 Click Connector(H140)Instrument Panel>Instrument Panel Wire / Speaker Wire>Electric Parking Brake Switch Assemblyewd_type=component;type=c;code=H140;pinno=7,8,1,2 |
||
| A94-36 (SWI1) - H140-7 (SWI1) | Always | Below 1 Ω |
| A94-31 (SWO1) - H140-8 (SWO1) | Always | Below 1 Ω |
| A94-41 (SWI2) - H140-1 (SWI2) | Always | Below 1 Ω |
| A94-39 (SWO2) - H140-2 (SWO2) | Always | Below 1 Ω |
| A94-36 (SWI1) or H140-7 (SWI1) - Body ground | Always | 10 kΩ or higher |
| A94-31 (SWO1) or H140-8 (SWO1) - Body ground | Always | 10 kΩ or higher |
| A94-41 (SWI2) or H140-1 (SWI2) - Body ground | Always | 10 kΩ or higher |
| A94-39 (SWO2) or H140-2 (SWO2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING