Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR DRIVE UNIT
RM3700E _59 Vehicle Exterior _093706 DOOR / HATCH _0444895 POWER BACK DOOR DRIVE UNIT A

DOOR / HATCH  POWER BACK DOOR DRIVE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
B599215N01
1.25,2.021 2.25,2.188 1,0.167 2.083,3.417 3.083,3.583 1,0.167 4.229,0.188 5.229,0.354 1,0.167 6.042,2.615 7.042,2.781 1,0.167 2.292,0.667 2.625,0.667 false 1.021,1.865 1.354,1.865 false 0.74,2.458 1.021,2.458 false 6.229,1.104 6.531,1.104 false 1.958,3.167 2.292,3.167 false 6.01,1.917 6.344,1.917 false 5.125,0.615 5.458,0.615 false 6.5,0.24 6.833,0.24 false 6.635,0.719 6.792,0.719 false 2.177,2.844 2.51,2.844 false 5.896,2.385 5.896,2.635 false 2.073,3.5 1.906,3.5 1.906,3.5 1.74,3.052 false 5.229,0.26 5.396,0.26 5.396,0.26 5.771,0.344 false 1.708,2.01 1.708,1.677 false 6.542,2.615 6.542,2.448 6.542,2.448 6.406,2.365 false 2.333,3 2.615,3.354 0.281,0.354 18 false 1 2.573,2.688 2.854,3.042 0.281,0.354 18 false 2 0.813,1.708 1.094,2.063 0.281,0.354 18 false 3 1.313,2.333 1.594,2.688 0.281,0.354 18 false 4 2.708,0.51 2.99,0.865 0.281,0.354 18 false 5 6.448,0.573 6.729,0.927 0.281,0.354 18 false 7 6.323,0.083 6.604,0.438 0.281,0.354 18 false 6 5.833,2.646 6.115,3 0.281,0.354 18 false 1 6.396,1.76 6.677,2.115 0.281,0.354 18 false 2 4.938,0.448 5.219,0.802 0.281,0.354 18 false 3 6.052,0.958 6.333,1.313 0.281,0.354 18 false 4 1.313,2.021 2.667,2.177 1.354,0.156 8 false 7.5 (76, 66 in.*lbf) 2.135,3.417 3.49,3.573 1.354,0.156 8 false 7.5 (76, 66 in.*lbf) 6.083,2.615 7.021,2.833 0.938,0.219 8 false 7.5 (76, 66 in.*lbf) 4.292,0.177 5.229,0.396 0.938,0.219 8 false 7.5 (76, 66 in.*lbf) 5.906,0.281 6.219,0.479 0.313,0.198 10 false x2 6.469,2.219 6.781,2.417 0.313,0.198 10 false x2 1.854,2.938 2.167,3.135 0.313,0.198 10 false x2 1.792,1.552 2.104,1.75 0.313,0.198 10 false x2 3.927,0.167 4.427,0.49 0.5,0.323 10 false ● ★ 0.948,2 1.448,2.323 0.5,0.323 10 false ● ★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BACK DOOR STAY STOPPER 68984 - - -
2 BACK DOOR LOWER DAMPER STAY BRACKET 68948 - - -
3 BACK DOOR UPPER DAMPER STAY BRACKET 68946 - - -
4 POWER BACK DOOR UNIT SET ASSEMBLY 68920 (Click here) - -
5 BACK DOOR TRIM BOARD 67751 - - -
6 INSPECT POWER BACK DOOR SYSTEM - (Click here) - -
7 ADJUST BACK DOOR - - - (Click here)

● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.



PROCEDURE

Hide 68984 1.INSTALL BACK DOOR STAY STOPPER

a.
B594655N01
0.135,0.083 0.417,0.438 0.281,0.354 18 false i

i.

Engage the claw and install the back door upper stay stopper to the back door lower damper stay bracket.



Hide 68948 2.INSTALL BACK DOOR LOWER DAMPER STAY BRACKET

a.
B594654N08
0.156,0.083 0.802,0.396 0.646,0.313 18 false i, ii, iii

i.

Clean the bolt holes in the vehicle body.


ii.

Apply adhesive to the threads of the 2 bolts

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



iii.

Install the back door lower damper stay bracket with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



Hide 68946 3.INSTALL BACK DOOR UPPER DAMPER STAY BRACKET

a.
B594653N04
0.063,0.021 1.438,0.375 1.375,0.354 18 false i, ii

i.

Clean the bolt holes in the vehicle body.


ii.

Install the back door upper damper stay bracket with the 2 new bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



Hide 68920 4.INSTALL POWER BACK DOOR UNIT SET ASSEMBLY

CAUTION:
·

Do not perform work if the back door is not securely supported.

·

The back door could fall, resulting in injury.


B594650


NOTICE:
·

Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.

·

Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.

·

Do not apply any horizontal load to the power back door unit assembly LH in order to prevent it from deforming.



a.
B599216N01
0.448,0.052 1.823,0.406 1.375,0.354 18 false i ,ii

i.

Engage the 2 ball joints to install the power back door unit assembly.

NOTICE:

Install the power back door unit assembly while supporting the back door by hand.



ii.

Check that the power back door unit assembly is engaged to the ball joints and that it cannot be pulled out.



b.
B594658C03
2.792,0.031 2.979,0.375 0.188,0.344 18 false i 4.333,1.302 4.51,1.573 0.177,0.271 18 true ii
V113147

Install in this Direction
V100135

Grommet
V100136

Connector - -


i.

Insert the harness through the service hole in the back door panel and connect the grommet.


ii.

Connect the Connector.



Hide 67751 5.INSTALL BACK DOOR TRIM BOARD

Hide 7.ADJUST BACK DOOR

HINT:

With the door upper stopper cushion or back damper stay lower bracket is removed,it is necessary to perform back door position adjustment.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR>ADJUSTMENT