Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093836 TELEMATICS _0444943 TELEMATICS SYSTEM(for Toyota Connected Services) C

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  B15C464  Airbag Signal Signal Plausibility Failure  


DESCRIPTION

If the telematics transceiver detects an error in communication between the telematics transceiver and the airbag sensor assembly as a result of the telematics transceiver self check, this DTC will be set.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15C464 Airbag Signal Signal Plausibility Failure Telematics transceiver detects an error in signals from airbag sensor assembly when ignition switch is ON.
·

Airbag system

·

Harness or connector

·

Airbag sensor assembly

·

Telematics transceiver


Telematics B

WIRING DIAGRAM

B469621E65
1.969,1.073 2.438,1.25 0.469,0.177 10 false GSW3 4.885,1.073 5.323,1.26 0.438,0.188 10 false GSW 1.115,2.063 1.469,2.354 0.354,0.292 10 false H14 1.115,2.229 2.927,2.448 1.813,0.219 10 false Airbag Sensor Assembly 4.677,2.042 5.396,2.26 0.719,0.219 10 false H85 4.667,2.219 6.802,2.521 2.135,0.302 10 false Telematics Transceiver 2.5,1.094 2.76,1.365 0.26,0.271 10 false 23 4.604,1.094 4.771,1.271 0.167,0.177 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CLEAR DTC (AIRBAG SYSTEM)
a.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC (AIRBAG SYSTEM)
2.CHECK DTC (AIRBAG SYSTEM)
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CLEAR DTC

B

3.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
B15C464 is output B
None of the above conditions are met C



A

B

5.CHECK TELEMATICS TRANSCEIVER (GSW SIGNAL)

C

5.CHECK TELEMATICS TRANSCEIVER (GSW SIGNAL)

Pre-procedure1

a.

Remove the telematics transceiver but do not disconnect the connectors.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Procedure1

a.
E422011C52
1.469,0.219 1.948,0.458 0.479,0.24 1.167,1.094 0.677,0.375 true 0.135,0.104 0.406,0.365 0.271,0.26 10 false *a 0.302,0.281 0.677,0.427 0.375,0.146 10 false GSW 1.563,0.26 2,0.51 0.438,0.25 10 false H85 0.208,4.031 0.646,4.292 0.438,0.26 10 false GND
*a Component with harness connected
(Telematics Transceiver)


Check the input waveform.

i.

Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telematics transceiver while the airbag sensor assembly connectors are connected.)

Reference Waveform:
Item Condition
Tester connection H85-13 (GSW) - Body ground
Tool setting 5.0 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON


OK:

The waveform is similar to that shown in the illustration.


Result:
Proceed to
OK
NG




Post-procedure1

a.

None



OK

6.REPLACE TELEMATICS TRANSCEIVER

NG

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - AIRBAG SENSOR ASSEMBLY)
6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


NOTICE:
·

The ignition switch must be off.

·

Do not exchange the telematics transceiver with one from another vehicle.




Result:
Proceed to
NEXT



NEXT

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - AIRBAG SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the H85 telematics transceiver connector.


b.

Disconnect the H14 airbag sensor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H85,H14)Location & Routing

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

Click Connector(H14)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Sensor Assembly

H85-13 (GSW) - H14-23 (GSW3) Always Below 1 Ω
H85-13 (GSW) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE HARNESS OR CONNECTOR