Refer to DTC C05061F.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C050614 | Right Front Wheel Speed Sensor Circuit Short to Ground or Open | An open in the speed sensor signal circuit continues for 0.5 seconds or more. | ·
Front speed sensor RH ·
Wire harness and connector ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Pre-procedure1
Select the line graph display on the GTS.
Procedure1
Check for any momentary interruption in the wire harness and connector.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Open | Front speed sensor RH open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Tester Display |
|---|
| FR Speed Open |
Normal (There are no momentary interruptions.)
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Drive the vehicle and perform a road test.
Procedure1
Check the speed value output from the speed sensor displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Operate the GTS to read the DTCs.
| Result | Proceed to |
|---|---|
| C050614 is not output | A |
| C050614 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the A23 front speed sensor RH connector.
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A23,A94)Location & Routingewd_type=routing;type=c,c;code=A23,A94 Click Connector(A23)Engine Compartment>Engine Room Main Wire>Front Speed Sensor RHewd_type=component;type=c;code=A23;pinno=1,2 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=7,6 |
||
| A23-1 (FR+) - A94-7 (FR+) | Always | Below 1 Ω |
| A23-1 (FR+) or A94-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| A23-2 (FR-) - A94-6 (FR-) | Always | Below 1 Ω |
| A23-2 (FR-) or A94-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Reconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Turn the ignition switch to ON.
Procedure2
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A23)Location & Routingewd_type=routing;type=c;code=A23 Click Connector(A23)Engine Compartment>Engine Room Main Wire>Front Speed Sensor RHewd_type=component;type=c;code=A23;pinno=1 |
||
| A23-1 (FR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG