Refer to DTC C05121F.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C051214 | Right Rear Wheel Speed Sensor Circuit Short to Ground or Open | An open in the speed sensor signal circuit continues for 0.5 seconds or more. | ·
Rear speed sensor RH (rear axle hub and bearing assembly RH) ·
Skid control sensor wire RH (No. 1 parking brake wire assembly) ·
Wire harness and connector ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Pre-procedure1
Select the line graph display on the GTS.
Procedure1
Check for any momentary interruption in the wire harness and connector.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Speed Open | Rear speed sensor RH open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Tester Display |
|---|
| RR Speed Open |
Normal (There are no momentary interruptions.)
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Drive the vehicle and perform a road test.
Procedure1
Check the speed value output from the speed sensor displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RR Wheel Speed |
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Operate the GTS to read the DTCs.
| Result | Proceed to |
|---|---|
| C051214 is not output | A |
| C051214 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the u2 and uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u2,uO1)Location & Routingewd_type=routing;type=c,w;code=u2,uO1 Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO1;pinno=4,3 |
||
| u2-2 (+) - uO1-4 (RR+) | Always | Below 1 Ω |
| u2-2 (+) or uO1-4 (RR+) - Body ground and other terminals | Always | 10 kΩ or higher |
| u2-1 (-) - uO1-3 (RR-) | Always | Below 1 Ω |
| u2-1 (-) or uO1-3 (RR-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO1,A94)Location & Routingewd_type=routing;type=w,c;code=uO1,A94 Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO1;pinno=4,3 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=20,19 |
||
| uO1-4 (RR+) - A94-20 (RR+) | Always | Below 1 Ω |
| uO1-4 (RR+) or A94-20 (RR+) - Body ground | Always | 10 kΩ or higher |
| uO1-3 (RR-) - A94-19 (RR-) | Always | Below 1 Ω |
| uO1-3 (RR-) or A94-19 (RR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Reconnect the A94 skid control ECU (brake actuator assembly) connector.
Reconnect the uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Turn the ignition switch to ON.
Procedure2
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u2)Location & Routingewd_type=routing;type=c;code=u2 |
||
| u2-2 (+) - Body ground | Ignition switch ON | 11 to 14 V |
The rear speed sensor RH is incorporated into the rear axle hub and bearing assembly RH.
If the rear speed sensor RH needs to be replaced, replace the rear axle hub and bearing assembly RH.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG