Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB (for 2WD) › 2020.08–2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441826 REAR AXLE HUB(for 2WD) A

AXLE AND DIFFERENTIAL  REAR AXLE HUB(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C444338N02
6.385,0.219 6.781,0.219 false 6.375,0.594 6.771,0.594 false 4.604,0.875 4.771,0.875 4.771,0.875 5.042,1.219 false 0.927,1.229 1,1 1,1 1.167,1 false 2.906,1.948 2.729,1.948 2.729,1.948 2.563,2.458 false 3.917,3.083 4.188,3.083 false 4.573,4.219 4.51,4.448 4.51,4.448 4.354,4.448 false 5.906,4.406 6.344,4.406 false 3.146,4.844 3.552,4.844 false 1.135,4.667 1.135,5 false 5.917,0.042 6.198,0.396 0.281,0.354 18 false 1 6.104,0.115 6.385,0.344 0.281,0.229 10 false (*A) 6.052,0.521 6.333,0.75 0.281,0.229 10 false (*A) 5.875,0.427 6.156,0.781 0.281,0.354 18 false 2 4.417,0.708 4.698,1.063 0.281,0.354 18 false 3 1.188,5.01 1.469,5.365 0.281,0.354 18 false 5 2.969,1.865 3.25,2.094 0.281,0.229 10 false *2 4.219,3 4.5,3.229 0.281,0.229 10 false *1 4.177,4.292 4.458,4.646 0.281,0.354 18 false 7 6.604,4.271 6.885,4.625 0.281,0.354 18 false 6 3.813,4.719 4.094,5.073 0.281,0.354 18 false 4 1.469,0.833 1.75,1.188 0.281,0.354 18 false 4 0.854,4.094 1.135,4.323 0.281,0.229 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - -
3 REAR WHEEL - - - -
4 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
5 REAR DISC BRAKE CALIPER ASSEMBLY - (Click here) - -
6 REAR DISC 42431 (Click here) - -
7 REAR AXLE HUB AND BEARING ASSEMBLY 42450B (Click here) - -

*A for HV Model - -
*1 REAR BRAKE DUST COVER *2 REAR CALIPER SUPPORT BRACKET

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. DISABLE BRAKE CONTROL (for HV Model)

Z101186

Click here(Click here)

Hide 3.REMOVE REAR WHEEL

Hide 890C0A 4.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C444343N02
0.396,0.063 0.677,0.417 0.281,0.354 18 false i 3.708,0.042 3.896,0.302 0.188,0.26 18 true ii

i.

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




ii.

Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.

NOTICE:

Be careful not to damage the rear axle hub and bearing assembly or connector cover.




Hide 5.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Z101186

Click here(Click here)

Hide 42431 6.REMOVE REAR DISC

Z101186

Click here(Click here)

Hide 42450B 7.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

a.
C444344N01
0.438,0.063 0.719,0.417 0.281,0.354 18 false i

i.

Remove the 4 bolts, rear axle hub and bearing assembly, rear brake dust cover and rear caliper support bracket from the rear axle beam assembly.

NOTICE:

Do not drop the rear brake dust cover and rear caliper support bracket.