Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0446873 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C057728  Brake Pressure Sensor "D" Signal Bias Level Out of Range / Zero Adjustment Failure  


DESCRIPTION

The reaction force pressure sensor detects and outputs the brake fluid pressure of the stroke simulator, which changes in accordance with brake pedal operation, to the skid control ECU (brake booster with master cylinder assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C057728 Brake Pressure Sensor "D" Signal Bias Level Out of Range / Zero Adjustment Failure When the brake pedal is not depressed, the reaction force pressure sensor output value is -0.63 MPa (-6.4 kgf/cm2, -91.4 psi) or less or 1.53 MPa (15.6 kgf/cm2, 222 psi) or more for 3 seconds or more. Skid control ECU (brake booster with master cylinder assembly) Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for HV Model)>ADJUSTMENT



c.

Adjust the brake pedal stroke sensor assembly.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR>INSTALLATION



Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (REACTION FORCE PRESSURE)
2.READ VALUE USING GTS (REACTION FORCE PRESSURE)
a.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reaction Force Pressure Pressure value of stroke simulator Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake/EPB > Data List
Tester Display
Reaction Force Pressure
50003 435 205

b.

Check that the reaction force pressure sensor output value is within 0.00 to 1.53 MPa when the brake pedal is not depressed.

OK:

The reaction force pressure sensor output value is within 0.00 to 1.53 MPa.


HINT:

If the reaction force pressure sensor output value is within 0.00 to 1.53 MPa, the skid control ECU (brake booster with master cylinder assembly) automatically performs zero point calibration every time the ignition switch is turned ON.

Therefore, if the reaction force pressure sensor output value is not within 0.00 to 1.53 MPa, replace the skid control ECU (brake booster with master cylinder assembly) with a new one.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
HINT:

Even if the DTC is cleared, it will immediately be output again if the reaction force pressure sensor zero point malfunction remains.


Result:
Result Proceed to
C057728 is not output A
C057728 is output B



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY