Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0441950 BRAKE PEDAL STROKE SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C442431N02
5.417,1.271 6.458,1.448 1.042,0.177 5.375,1.229 6.5,1.49 1.125,0.26 4.219,1.271 4.406,1.458 4.406,1.458 4.573,1.458 false 4.823,0.969 5.25,1.365 5.25,1.365 5.417,1.365 false 6.448,0.281 6.781,0.281 false 6.448,0.771 6.781,0.771 false 4.917,1.323 5.198,1.677 0.281,0.354 18 false 2 4.854,0.833 5.156,1.042 0.302,0.208 10 false x2 5.49,1.271 6.615,1.479 1.125,0.208 8 false 8.5 (87, 75 in.*lbf) 5.917,0.146 6.417,0.5 0.5,0.354 18 false 1, 4 6.177,0.625 6.427,0.958 0.25,0.333 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSPECT AND ADJUST BRAKE PEDAL HEIGHT - - - (Click here)
2 BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D (Click here) - -
3 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) - -

C442432N01
2.823,0.688 3.156,0.688 false 6.167,1.906 6.5,1.906 false 6.469,0.281 6.802,0.281 false 3.25,0.563 3.5,0.927 0.25,0.365 18 false 5 2.24,1.646 2.563,1.896 0.323,0.25 10 false x2 4.875,3.125 5.198,3.375 0.323,0.25 10 false x2 6.552,1.771 6.802,2.135 0.25,0.365 18 false 6 5.708,0.125 6.458,0.531 0.75,0.406 18 false 7, 8, 9

Procedure Part Name Code
Z101186

Z101188

Z101187

5 NO. 1 AIR DUCT 87211 - - -
6 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
7 PERFORM CALIBRATION - (Click here) - -
8 CHECK AND CLEAR DTC - (Click here) - -
9 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - (Click here) - -

● Non-reusable part - -

PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

Hide 89510D 2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

Z101186

NOTICE:
·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.




a.

When installing a new brake pedal stroke sensor assembly:

C442433C01
4.094,3.135 4.167,2.917 4.167,2.917 4.333,2.917 true 4.167,3.5 4,3.5 4,3.5 3.979,3.26 true 3.896,0.521 3.969,0.302 3.969,0.302 4.135,0.302 true 3.01,2.063 3.26,2.313 0.25,0.25 18 true i 3.156,1.385 3.406,1.635 0.25,0.25 18 true ii 2.844,0.125 3.094,0.375 0.25,0.25 18 true iii 4.323,2.844 4.552,3.031 0.229,0.188 10 true *a 4.188,3.417 4.417,3.604 0.229,0.188 10 true *b 4.146,0.208 4.375,0.396 0.229,0.188 10 true *c
*a Brake Pedal Stroke Sensor Assembly Lever *b Brake Pedal Groove
*c Brake Pedal Groove - -


i.

Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.




ii.

Connect the connector.


iii.

Firmly depress the brake pedal to break the brake pedal stroke sensor assembly lever set pin.

NOTICE:

Remove the broken lever set pin.




b.

When reusing the brake pedal stroke sensor assembly:

C442434C01
4.302,2.615 4.406,2.417 4.406,2.417 4.573,2.417 true 4.219,2.781 4.333,3 4.333,3 4.5,3 true 4.573,2.323 4.792,2.49 0.219,0.167 10 true *a 4.5,2.906 4.708,3.104 0.208,0.198 10 true *b 3.042,1.573 3.229,1.865 0.188,0.292 18 true i 3.313,0.844 3.5,1.135 0.188,0.292 18 true ii
*a Brake Pedal Stroke Sensor Assembly Lever *b Brake Pedal Groove


i.

Install the brake pedal stroke sensor assembly to the brake pedal support assembly and temporarily tighten the 2 nuts.

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.




ii.

Connect the connector.



Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89510D 4.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

Z101186

NOTICE:

When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.



a.
C442435N01
0.448,0.073 0.729,0.427 0.281,0.354 18 false i

i.

Check the data monitor by the following procedure.

1. Connect the GTS to the DLC3 with the ignition switch off.

2. Turn the ignition switch to ON.

3. Turn the GTS on.

4. Enter the following menus: Chassis / Brake/EPB > Data List / Stroke Sensor.

Chassis > Brake/EPB > Data List
Tester Display
Stroke Sensor
50003 435 207


b.
C442436N01
0.438,0.042 1.813,0.396 1.375,0.354 18 false i, ii

i.

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



ii.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not depress the brake pedal after turning the ignition switch to ON.




c.
C442435N01
0.448,0.073 0.729,0.427 0.281,0.354 18 false i

i.

Follow the steps below to finish the work.

1. Turn the GTS off and turn the ignition switch off.

2. Disconnect the GTS from the DLC3.



Hide 55606 6.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 9. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART