Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.08–2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0445205 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Check Bus 5 Line  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen.
·

CAN main bus line, CAN branch line or connector

·

Central gateway ECU (network gateway ECU)

·

Certification ECU (smart key ECU assembly)

(w/ Entry and Start System)

·

Air conditioning amplifier assembly

·

Multiplex network door ECU

(w/ Power Back Door)

·

Main body ECU (multiplex network body ECU)

·

No. 11 global CAN junction connector

·

No. 12 global CAN junction connector



WIRING DIAGRAM

C444856E01
5,1.781 7.052,2.188 2.052,0.406 10 false Central Gateway ECU (Network Gateway ECU) 5,1.604 5.646,1.896 0.646,0.292 10 false H40 5.375,0.552 6.021,0.844 0.646,0.292 10 false CA5H 4,0.563 4.646,0.854 0.646,0.292 10 false 1 1.76,0.563 2.406,0.854 0.646,0.292 10 false 1 2.729,0.573 3.375,0.865 0.646,0.292 10 false 3 5.146,0.552 5.792,0.844 0.646,0.292 10 false 7 1.229,0.677 1.875,0.969 0.646,0.292 10 false CANH 5.375,1.104 6.021,1.396 0.646,0.292 10 false CA5L 5.167,1.104 5.813,1.396 0.646,0.292 10 false 8 2.729,1.104 3.375,1.396 0.646,0.292 10 false 7 1.76,1.104 2.406,1.396 0.646,0.292 10 false 2 4.01,1.115 4.656,1.406 0.646,0.292 10 false 5 4.01,1.552 4.656,1.844 0.646,0.292 10 false 6 4.021,1.896 4.667,2.188 0.646,0.292 10 false 2 1.75,3.469 2.396,3.76 0.646,0.292 10 false 2 1.76,4.01 2.406,4.302 0.646,0.292 10 false 1 2.719,3.458 3.365,3.75 0.646,0.292 10 false 2 2.719,4.01 3.365,4.302 0.646,0.292 10 false 8 4,4.01 4.646,4.302 0.646,0.292 10 false 11 3.99,3.479 4.635,3.771 0.646,0.292 10 false 5 4.01,5.083 4.656,5.375 0.646,0.292 10 false 6 1.75,5.667 2.396,5.958 0.646,0.292 10 false 9 1.76,6.198 2.406,6.49 0.646,0.292 10 false 26 5.146,5.104 5.792,5.396 0.646,0.292 10 false 10 3.99,5.635 4.635,5.927 0.646,0.292 10 false 12 5.146,5.625 5.792,5.917 0.646,0.292 10 false 20 4,7.188 4.646,7.479 0.646,0.292 10 false 4 3.979,7.729 4.625,8.021 0.646,0.292 10 false 10 5.167,7.177 5.813,7.469 0.646,0.292 10 false 2 5.167,7.719 5.813,8.01 0.646,0.292 10 false 1 1.26,1.208 1.906,1.5 0.646,0.292 10 false CANL 0.5,1.594 1.146,1.885 0.646,0.292 10 false H46 0.5,1.76 2.042,2.271 1.542,0.51 10 false Certification ECU (Smart Key ECU Assembly)*1 2.531,2.375 3.177,2.667 0.646,0.292 10 false H142 2.531,2.552 4.271,3.031 1.74,0.479 10 false No. 11 Global CAN Junction Connector 1.26,3.583 1.906,3.875 0.646,0.292 10 false CANH 1.26,4.135 1.906,4.427 0.646,0.292 10 false CANL 0.385,4.708 1.969,5.167 1.583,0.458 10 false Air Conditioning Amplifier Assembly*3 0.375,4.521 1.021,4.813 0.646,0.292 10 false H24 1.26,5.76 1.906,6.052 0.646,0.292 10 false CANH 1.25,6.302 1.896,6.594 0.646,0.292 10 false CANL 0.427,6.865 2.01,7.323 1.583,0.458 10 false Air Conditioning Amplifier Assembly*4 0.406,6.688 1.052,6.979 0.646,0.292 10 false H23 5.406,5.177 6.052,5.469 0.646,0.292 10 false CANP 5.417,5.719 6.063,6.01 0.646,0.292 10 false CANN 4.958,6.323 6.917,6.875 1.958,0.552 10 false Multiplex Network Door ECU*2 4.958,6.146 5.604,6.438 0.646,0.292 10 false Y30 5.365,7.188 6.01,7.479 0.646,0.292 10 false CANH 5.365,7.708 6.01,8 0.646,0.292 10 false CANL 5.167,8.406 6.833,9.094 1.667,0.688 10 false Main Body ECU (Multiplex Network Body ECU) 5.167,8.229 5.813,8.521 0.646,0.292 10 false H4 2.542,8.229 3.188,8.521 0.646,0.292 10 false O114 2.552,8.396 4.313,8.958 1.76,0.563 10 false No. 12 Global CAN Junction Connector 0.198,9.031 2.417,9.479 2.219,0.448 10 false *1: w/ Entry and Start System 0.208,9.427 2.427,9.875 2.219,0.448 10 false *2: w/ Power Back Door 2.552,9.031 5.594,9.375 3.042,0.344 10 false *3: for Automatic Air Conditioning System 2.542,9.427 5.854,9.823 3.313,0.396 10 false *4: for Manual Air Conditioning System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.*1


*1: w/ Entry and Start System



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C425195C73
1.51,0.073 1.927,0.323 0.417,0.25 2.271,0.688 2.635,0.229 true 2.146,0.781 2.677,1.708 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.135 2.063,0.333 0.458,0.198 10 false H40 2.729,1.708 3.198,1.927 0.469,0.219 10 false CA5L 2.677,0.104 3.156,0.271 0.479,0.167 10 false CA5H
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-7 (CA5H) - H40-8 (CA5L) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES

NG

47.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR SHORT IN CAN BUS LINES
a.
C425195C73
1.51,0.073 1.927,0.323 0.417,0.25 2.271,0.688 2.635,0.229 true 2.146,0.781 2.677,1.708 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.135 2.063,0.333 0.458,0.198 10 false H40 2.729,1.708 3.198,1.927 0.469,0.219 10 false CA5L 2.677,0.104 3.156,0.271 0.479,0.167 10 false CA5H
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-7 (CA5H) - H40-8 (CA5L) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Result
OK
NG



OK

3.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

33.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C55
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.292 5.729,0.563 0.417,0.271 6.271,1.615 6.552,2.01 true 2.615,1.125 2.917,0.583 true 2.531,1.198 3.042,2.104 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 3.063,2.094 3.615,2.292 0.552,0.198 10 false CA5L 6.594,1.979 7.146,2.177 0.552,0.198 10 false BAT 2.958,0.458 3.51,0.656 0.552,0.198 10 false CA5H 5.417,0.344 5.729,0.542 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-7 (CA5H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-8 (CA5L) - H3-16 (BAT)



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

19.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
4.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C56
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.135 5.729,0.406 0.417,0.271 5.427,1.042 6.01,0.531 true 2.625,1.125 3.083,0.583 true 2.531,1.208 3.094,2.125 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 3.135,2.083 3.688,2.281 0.552,0.198 10 false CA5L 6.052,0.448 6.604,0.646 0.552,0.198 10 false CG 3.115,0.469 3.667,0.667 0.552,0.198 10 false CA5H 5.417,0.198 5.729,0.396 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-7 (CA5H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-8 (CA5L) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H142 No. 11 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H142-5 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 12 GLOBAL CAN JUNCTION CONNECTOR)

NG

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 12 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to No. 12 Global CAN Junction Connector
H142-6 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

7.CHECK VEHICLE TYPE

NG

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
7.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Certification ECU (Smart Key ECU Assembly)
H142-7 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

NG

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H142-5 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Certification ECU (Smart Key ECU Assembly)
H142-7 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the O114 No. 12 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-5 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to No. 11 Global CAN Junction Connector
O114-11 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Air Conditioning Amplifier Assembly
O114-8 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

13.CHECK VEHICLE TYPE

NG

16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
13.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Power Back Door A
w/o Power Back Door B



A

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

B

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-6 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Multiplex Network Door ECU
O114-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

17.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Main Body ECU (Multiplex Network Body ECU)
O114-10 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 12 GLOBAL CAN JUNCTION CONNECTOR

NG

18.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the H24*1 or H23*2 air conditioning amplifier assembly connector.

*1: for Automatic Air Conditioning System


*2: for Manual Air Conditioning System



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Air Conditioning Amplifier Assembly
O114-8 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

17.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the Y30 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-6 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Multiplex Network Door ECU
O114-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

18.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Main Body ECU (Multiplex Network Body ECU)
O114-10 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

19.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H142 No. 11 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H142-5 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 12 GLOBAL CAN JUNCTION CONNECTOR)

NG

23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 12 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to No. 12 Global CAN Junction Connector
H142-6 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

21.CHECK VEHICLE TYPE

NG

25.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
21.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

22.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

22.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Certification ECU (Smart Key ECU Assembly)
H142-7 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

NG

24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H142-5 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142,H3)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H142-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Certification ECU (Smart Key ECU Assembly)
H142-7 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

25.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the O114 No. 12 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-5 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to No. 11 Global CAN Junction Connector
O114-11 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

26.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

26.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Air Conditioning Amplifier Assembly
O114-8 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

27.CHECK VEHICLE TYPE

NG

30.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
27.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Power Back Door A
w/o Power Back Door B



A

28.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

B

29.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
28.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-6 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Multiplex Network Door ECU
O114-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

29.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

31.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
29.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Main Body ECU (Multiplex Network Body ECU)
O114-10 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 12 GLOBAL CAN JUNCTION CONNECTOR

NG

32.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
30.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the H24*1 or H23*2 air conditioning amplifier assembly connector.

*1: for Automatic Air Conditioning System


*2: for Manual Air Conditioning System



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Air Conditioning Amplifier Assembly
O114-8 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

31.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the Y30 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-6 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Multiplex Network Door ECU
O114-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

32.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114,H3)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O114-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Main Body ECU (Multiplex Network Body ECU)
O114-10 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

33.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H142 No. 11 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

H142-1 (CANH) - H142-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

34.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 12 GLOBAL CAN JUNCTION CONNECTOR)

NG

37.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
34.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 12 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

H142-2 (CANH) - H142-6 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 12 Global CAN Junction Connector



Result:
Result
OK
NG



OK

35.CHECK VEHICLE TYPE

NG

39.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
35.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

36.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

36.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

H142-3 (CANH) - H142-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Certification ECU (Smart Key ECU Assembly)



Result:
Result
OK
NG



OK

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

NG

38.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
37.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

H142-1 (CANH) - H142-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

38.CHECK FOR SHORT IN CAN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

H142-3 (CANH) - H142-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Certification ECU (Smart Key ECU Assembly)



Result:
Result
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

39.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the O114 No. 12 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

O114-5 (CANH) - O114-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 11 Global CAN Junction Connector



Result:
Result
OK
NG



OK

40.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

40.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

O114-2 (CANH) - O114-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Air Conditioning Amplifier Assembly



Result:
Result
OK
NG



OK

41.CHECK VEHICLE TYPE

NG

44.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
41.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Power Back Door A
w/o Power Back Door B



A

42.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

B

43.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
42.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

O114-6 (CANH) - O114-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Multiplex Network Door ECU



Result:
Result
OK
NG



OK

43.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

45.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
43.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

O114-4 (CANH) - O114-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Main Body ECU (Multiplex Network Body ECU)



Result:
Result
OK
NG



OK

REPLACE NO. 12 GLOBAL CAN JUNCTION CONNECTOR

NG

46.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
44.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the H24*1 or H23*2 air conditioning amplifier assembly connector.

*1: for Automatic Air Conditioning System


*2: for Manual Air Conditioning System



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

O114-2 (CANH) - O114-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Air Conditioning Amplifier Assembly



Result:
Result
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

45.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the Y30 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

O114-6 (CANH) - O114-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Multiplex Network Door ECU



Result:
Result
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

46.CHECK FOR SHORT IN CAN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

O114-4 (CANH) - O114-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Main Body ECU (Multiplex Network Body ECU)



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

47.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-7 (CA5H) - H40-8 (CA5L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 11 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

48.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
48.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H142 No. 11 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

H142-1 (CANH) - H142-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

49.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 12 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

49.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 12 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H142)Location & Routing

Click Connector(H142)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 11 Global CAN Junction Connector

H142-2 (CANH) - H142-6 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 12 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

NG

50.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
50.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the O114 No. 12 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

O114-5 (CANH) - O114-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 11 Global CAN Junction Connector



Result:
Result
OK
NG



OK

51.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

51.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 12 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O114)Location & Routing

Click Connector(O114)Body>Floor Wire>No. 12 Global CAN Junction Connector

O114-4 (CANH) - O114-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Main Body ECU (Multiplex Network Body ECU)



Result:
Result
OK
NG



OK

REPLACE NO. 12 GLOBAL CAN JUNCTION CONNECTOR

NG

52.CHECK FOR OPEN IN CAN MAIN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
52.CHECK FOR OPEN IN CAN MAIN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H4)Location & Routing

Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECU

H4-2 (CANH) - H4-1 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 12 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 12 GLOBAL CAN JUNCTION CONNECTOR)