When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. The ECM uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the ECM determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| P057162 | Brake Switch "A" Signal Compare Failure | When the ignition switch is ON and the dynamic radar cruise control system is operating, the ECM detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more. | ·
Harness or connector ·
Stop light switch assembly ·
ECM |
Radar Cruise1 | A |
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the ECM, refer to Service Bulletin.
Pre-procedure1
Disconnect the A63 stop light switch assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63)Location & Routingewd_type=routing;type=c;code=A63 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=2 |
||
| A63-2 (GND) - Body ground | Always | Below 1 Ω |
Procedure2
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63)Location & Routingewd_type=routing;type=c;code=A63 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=7,6 |
||
| A63-7 (B) - Body ground | Always | 11 to 14 V |
| A63-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| A63-6 (B) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the A63 stop light switch assembly connector.
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| w/ Entry and Start System | A |
| w/o Entry and Start System | B |
A
B
Pre-procedure1
Disconnect the A54 ECM connector.
Disconnect the A63 stop light switch assembly connector.
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Disconnect the H45 certification ECU (smart key ECU assembly) connector.
Disconnect the F20 shift lock control ECU (shift lock control unit assembly) connector.
Disconnect the D71 TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A54,A63)Location & Routingewd_type=routing;type=c,c;code=A54,A63 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=22,21 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=5,3 |
||
| A54-22 (ST1-) - A63-5 (L) | Always | Below 1 Ω |
| A54-21 (STP) - A63-3 (L) | Always | Below 1 Ω |
| A54-22 (ST1-) or A63-5 (L) - Body ground | Always | 10 kΩ or higher |
| A54-21 (STP) or A63-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the D71 TCM connector.
Connect the F20 shift lock control ECU (shift lock control unit assembly) connector.
Connect the H45 certification ECU (smart key ECU assembly) connector.
Connect the A94 skid control ECU (brake actuator assembly) connector.
Connect the A63 stop light switch assembly connector.
Connect the A54 ECM connector.
OK
NG
Pre-procedure1
Disconnect the A54 ECM connector.
Disconnect the A63 stop light switch assembly connector.
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Disconnect the F19 shift lock control ECU (shift lock control unit assembly) connector.
Disconnect the D71 TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A54,A63)Location & Routingewd_type=routing;type=c,c;code=A54,A63 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=22,21 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=5,3 |
||
| A54-22 (ST1-) - A63-5 (L) | Always | Below 1 Ω |
| A54-21 (STP) - A63-3 (L) | Always | Below 1 Ω |
| A54-22 (ST1-) or A63-5 (L) - Body ground | Always | 10 kΩ or higher |
| A54-21 (STP) or A63-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the D71 TCM connector.
Connect the F19 shift lock control ECU (shift lock control unit assembly) connector.
Connect the A94 skid control ECU (brake actuator assembly) connector.
Connect the A63 stop light switch assembly connector.
Connect the A54 ECM connector.
OK
NG