Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › FRONT CAMERA SYSTEM
RM3700E _95 ADAS / AD _095278 ADVANCED DRIVER ASSISTANCE SYSTEM _0447903 FRONT CAMERA SYSTEM C

ADVANCED DRIVER ASSISTANCE SYSTEM  FRONT CAMERA SYSTEM  C1AAE00  Front Recognition Camera Heater Malfunction  


DESCRIPTION

The forward recognition camera controls the flow of current to the forward recognition with heater hood sub-assembly.

If the forward recognition camera detects a malfunction in the forward recognition with heater hood sub-assembly circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1AAE00 Front Recognition Camera Heater Malfunction
Either of the following conditions is met after 10 seconds have elapsed since the ignition switch was turned to ON:
·

Short to +B detected in the forward recognition with heater hood sub-assembly circuit for 1 second or more cumulatively

·

Open or short to ground detected in the forward recognition with heater hood sub-assembly circuit for 5 seconds or more


·

Forward recognition with heater hood sub-assembly

·

Forward recognition camera

·

Wire harness or connector


Front Recognition Camera A

WIRING DIAGRAM

A398326E80
0.083,0.667 3.146,0.865 3.063,0.198 10 false from IGR-NO. 2 Relay 2.031,0.833 3.073,1.052 1.042,0.219 10 false ECU-IGR NO. 2 3.156,1.229 5.26,1.615 2.104,0.385 10 false Forward Recognition with Heater Hood Sub-assembly 3.583,0.708 4.042,0.906 0.458,0.198 10 false IG1 4.125,0.698 4.583,0.896 0.458,0.198 10 false HTR 3.396,0.594 3.552,0.792 0.156,0.198 10 false 1 4.5,0.583 4.656,0.781 0.156,0.198 10 false 2 5.344,0.583 5.5,0.781 0.156,0.198 10 false 1 5.531,0.688 5.99,0.885 0.458,0.198 10 false HTR 3.177,1.052 4.094,1.25 0.917,0.198 10 false V11 5.104,2.073 5.563,2.271 0.458,0.198 10 false V10 5.094,2.26 6.958,2.49 1.865,0.229 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Front Recognition Camera > Clear DTCs
50002 430

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTCs
2.CHECK FOR DTCs

Pre-procedure1

a.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



Procedure1

a.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 430
Result:
Result Proceed to
C1AAE00 is not output A
C1AAE00 is output B



Post-procedure1

a.

None.



A

B

3.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
3.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


b.
C367122C30
1.26,1.781 1.594,1.25 true 2.094,1.792 1.833,1.25 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.052,1.792 1.51,1.99 0.458,0.198 10 false HTR 2.073,1.823 2.531,2.021 0.458,0.198 10 false IG1
*a Component without harness connected
(Forward Recognition with Heater Hood Sub-assembly)


Disconnect the V11 forward recognition with heater hood sub-assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (IG1) - 2 (HTR) Ignition switch off 25.6 to 28.4 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the V11 forward recognition with heater hood sub-assembly connector.



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPLACE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

Pre-procedure1

a.

Disconnect the V11 forward recognition with heater hood sub-assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(V11)Location & Routing

Click Connector(V11)Body>No. 1 Roof Wire>Forward Recognition with Heater Hood Sub-Assembly

V11-1 (IG1) - Body ground Ignition switch ON 8 to 16 V
V11-1 (IG1) - Body ground Ignition switch off Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the V11 forward recognition with heater hood sub-assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

Pre-procedure1

a.

Disconnect the V11 forward recognition with heater hood sub-assembly connector.


b.

Disconnect the V10 forward recognition camera connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V11,V10)Location & Routing

Click Connector(V11)Body>No. 1 Roof Wire>Forward Recognition with Heater Hood Sub-Assembly

Click Connector(V10)Body>No. 1 Roof Wire>Forward Recognition Camera

V11-2 (HTR) - V10-1 (HTR) Always Below 1 Ω
V11-2 (HTR) or V10-1 (HTR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the V10 forward recognition camera connector.


b.

Connect the V11 forward recognition with heater hood sub-assembly connector.



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)