Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0446873 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  Downhill Assist Control Indicator Light does not Come ON  


DESCRIPTION

Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:

·

Check that the shift lever is in P.

·

The vehicle speed is 35 km/h (22 mph) or more.

·

The brake system is malfunctioning.

·

Temperature of the brake booster with master cylinder assembly increases and the downhill assist control is temporarily canceled.


WIRING DIAGRAM

C427345E09
5.385,2.75 6,2.948 0.615,0.198 10 false HDCS 4.313,2.75 4.927,2.948 0.615,0.198 10 false B 3.667,2.75 4.281,2.948 0.615,0.198 10 false E 3.417,2.75 4.031,2.948 0.615,0.198 10 false 2 4.563,2.729 5.177,2.927 0.615,0.198 10 false 5 5.104,3.917 5.719,4.115 0.615,0.198 10 false A38 0.24,3.938 0.854,4.135 0.615,0.198 10 false H6 0.219,4.115 2.219,4.302 2,0.188 10 false Combination Meter Assembly 2.927,4.354 4.927,4.542 2,0.188 10 false : CAN Communication Line 5.063,4.104 7.125,4.781 2.063,0.677 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.271,3.385 5.271,3.573 2,0.188 10 false Downhill Assist Control Switch 5.385,1.75 6,1.948 0.615,0.198 10 false CA1L 0.865,0.938 1.479,1.135 0.615,0.198 10 false CANH 5,1.542 5.615,1.74 0.615,0.198 10 false 42 4.938,0.75 5.552,0.948 0.615,0.198 10 false 43 1.427,0.729 2.042,0.927 0.615,0.198 10 false 9 1.417,1.563 2.031,1.76 0.615,0.198 10 false 25 5.385,0.896 6,1.094 0.615,0.198 10 false CA1H 0.854,1.729 1.469,1.927 0.615,0.198 10 false CANL 3.25,3.208 5.25,3.396 2,0.188 10 false H133

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.

Turn the ignition switch off.


b.

Inspect the downhill assist control switch.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>INSPECTION

OK:

The downhill assist control switch operates normally.



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)

NG

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)
a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A38,H133)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

Click Connector(H133)Instrument Panel>Instrument Panel Wire / Speaker Wire>Downhill Assist Control Switch

A38-6 (HDCS) - H133-5 (B) Always Below 1 Ω
A38-6 (HDCS) or H133-5 (B) - Body ground Always 10 kΩ or higher
H133-2 (E) - Body ground Always Below 1 Ω


Result:
Result
OK
NG




OK

3.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Downhill Assist Control Indicator
50004 409 119

b.

Check the combination meter assembly.

OK:

The Downhill assist control indicator light turns on or off in accordance with the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG