Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0444807 ELECTRIC PARKING BRAKE SYSTEM(for HV Model) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model)  C060E19  Left Electric Parking Brake Actuator Circuit Current Above Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C060E19 Left Electric Parking Brake Actuator Circuit Current Above Threshold When the electric parking brake is operating, overcurrent is detected in the parking brake actuator assembly LH 3 times.
·

Parking brake actuator assembly LH

·

No. 2 parking brake wire assembly

·

Wire harness and connector

·

Parking brake ECU (brake actuator assembly)


DTC stored Electric Parking Brake A An electric parking brake system malfunction is displayed on the multi-information display.

CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the parking brake ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.



PROCEDURE

1.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the uO2 and u3 No. 2 parking brake wire assembly connectors.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

C390252C17
1.479,0.135 1.896,0.385 0.417,0.25 5,0.333 5.417,0.583 0.417,0.25 4.323,2.177 5,1.667 true 5.417,1.667 6.083,2.156 true 1.573,0.177 2.031,0.375 0.458,0.198 10 false uO2 5.104,0.396 5.563,0.594 0.458,0.198 10 false u3 6.177,2.073 6.594,2.323 0.417,0.25 10 false + 4.156,2.083 4.615,2.281 0.458,0.198 10 false - 1.604,2.563 2.063,2.771 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 5.146,2.25 5.604,2.448 0.458,0.198 10 false *c
*a Front view of No. 2 Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly LH) - -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,u3)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

uO2-1 - u3-2 (+) Always Below 1 Ω
uO2-1 or u3-2 (+) - Body ground and other terminals Always 10 kΩ or higher
uO2-2 - u3-1 (-) Always Below 1 Ω
uO2-2 or u3-1 (-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

Pre-procedure1

a.

Make sure the No. 2 parking brake wire assembly is securely installed.


b.

Disconnect the A95 parking brake ECU (brake actuator assembly) connector.


c.

Disconnect the u3 parking brake actuator assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A95,u3)Location & Routing

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

A95-7 (MRL+) - u3-2 (+) Always Below 1 Ω
A95-7 (MRL+) or u3-2 (+) - Body ground Always 10 kΩ or higher
A95-8 (MRL-) - u3-1 (-) Always Below 1 Ω
A95-8 (MRL-) or u3-1 (-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK VEHICLE TYPE
a.

Check the vehicle specification.


Result:
Result Proceed to
for 2WD A
for AWD B



A

4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

B

8.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH
4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

OK

5.CHECK FOR SHORT TO +B

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

5.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Turn the ignition switch off.


b.

Make sure the No. 2 parking brake wire assembly is securely installed.


c.

Disconnect the u3 parking brake actuator assembly LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u3)Location & Routing

Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

u3-2 (+) - u3-1 (-) Electric parking brake not operating Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

NG

6.CHECK FOR SHORT TO +B
6.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Disconnect the uO2 No. 2 parking brake wire assembly connector.


Procedure1

a.
C390253C04
1.5,0.188 1.917,0.438 0.417,0.25 0.208,0.281 0.51,0.51 0.302,0.229 10 false *a 1.604,0.229 1.906,0.458 0.302,0.229 10 false uO2
*a Front view of wire harness connector
(to No. 2 Parking Brake Wire Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-1 - uO2-2 Electric parking brake not operating Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

7.CHECK FOR SHORT TO +B
7.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Disconnect the uO2 No. 2 parking brake wire assembly connector.


b.

Disconnect the A95 parking brake ECU (brake actuator assembly) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

C390254C04
1.781,0.417 2.198,0.667 0.417,0.25 5.125,0.417 5.542,0.667 0.417,0.25 3.021,2.375 2.438,1.521 true 1.625,2.333 2.208,1.5 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false A95 5.229,0.479 5.688,0.677 0.458,0.198 10 false uO2 0.5,0.75 0.958,1.031 0.458,0.281 10 false *b 0.167,0.167 0.583,0.417 0.417,0.25 10 false *a 4.583,0.75 5.125,0.948 0.542,0.198 10 false *c 2.958,2.406 3.458,2.656 0.5,0.25 10 false MRL- 1.406,2.396 1.906,2.646 0.5,0.25 10 false MRL+
*a Front view of wire harness connector *b (to Parking Brake ECU (Brake Actuator Assembly))
*c (to No. 2 Parking Brake Wire Assembly) - -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,A95)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

uO2-1 or A95-7 (MRL+) - Body ground Always Below 1 V
uO2-2 or A95-8 (MRL-) - Body ground Always Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

OK

9.CHECK FOR SHORT TO +B

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

9.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Turn the ignition switch off.


b.

Make sure the No. 2 parking brake wire assembly is securely installed.


c.

Disconnect the u3 parking brake actuator assembly LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u3)Location & Routing

Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

u3-2 (+) - u3-1 (-) Electric parking brake not operating Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

NG

10.CHECK FOR SHORT TO +B
10.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Disconnect the uO2 No. 2 parking brake wire assembly connector.


Procedure1

a.
C390253C04
1.5,0.188 1.917,0.438 0.417,0.25 0.208,0.281 0.51,0.51 0.302,0.229 10 false *a 1.604,0.229 1.906,0.458 0.302,0.229 10 false uO2
*a Front view of wire harness connector
(to No. 2 Parking Brake Wire Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

uO2-1 - uO2-2 Electric parking brake not operating Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

11.CHECK FOR SHORT TO +B
11.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Disconnect the uO2 No. 2 parking brake wire assembly connector.


b.

Disconnect the A95 parking brake ECU (brake actuator assembly) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

C390254C04
1.781,0.417 2.198,0.667 0.417,0.25 5.125,0.417 5.542,0.667 0.417,0.25 3.021,2.375 2.438,1.521 true 1.625,2.333 2.208,1.5 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false A95 5.229,0.479 5.688,0.677 0.458,0.198 10 false uO2 0.5,0.75 0.958,1.031 0.458,0.281 10 false *b 0.167,0.167 0.583,0.417 0.417,0.25 10 false *a 4.583,0.75 5.125,0.948 0.542,0.198 10 false *c 2.958,2.406 3.458,2.656 0.5,0.25 10 false MRL- 1.406,2.396 1.906,2.646 0.5,0.25 10 false MRL+
*a Front view of wire harness connector *b (to Parking Brake ECU (Brake Actuator Assembly))
*c (to No. 2 Parking Brake Wire Assembly) - -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,A95)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

uO2-1 or A95-7 (MRL+) - Body ground Always Below 1 V
uO2-2 or A95-8 (MRL-) - Body ground Always Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR