Home › Drivetrain › CLUTCH › CLUTCH MASTER CYLINDER (for LHD) › from 2021.07
RM3700E _52 Drivetrain _104786 CLUTCH _0480193 CLUTCH MASTER CYLINDER(for LHD) A

CLUTCH  CLUTCH MASTER CYLINDER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C459827N01
4.396,2.896 4.073,2.896 false 3.406,3.667 2.083,3.5 2.083,3.5 1.823,3.5 true 3.01,1.281 2.688,1.281 false 5.427,3.573 5.104,3.573 false 5.938,4.979 5.615,4.979 false 6.396,4.521 6.156,4.521 6.156,4.521 5.844,4.26 false 3.323,4.646 3,4.646 false 3.083,1.115 3.365,1.469 0.281,0.354 18 false 1 4.49,2.729 4.771,3.083 0.281,0.354 18 false 2 1.563,3.333 1.844,3.688 0.281,0.354 18 false 3 5.49,3.469 5.646,3.667 0.156,0.198 10 false ● 6.021,4.813 6.302,5.167 0.281,0.354 18 false 4 6.458,4.417 6.615,4.615 0.156,0.198 10 false ● 6.469,4 6.781,4.198 0.313,0.198 10 false x2 2.802,4.479 3.083,4.833 0.281,0.354 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE BOOSTER ASSEMBLY 44610 - - -
2 NO. 1 CLUTCH RESERVOIR HOSE 31434E - - -
3 CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE 31481 (Click here) - -
4 CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN 31453A - - -
5 CLUTCH MASTER CYLINDER ASSEMBLY 31410 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 44610 1.REMOVE BRAKE BOOSTER ASSEMBLY

Hide 31434E 2.DISCONNECT NO. 1 CLUTCH RESERVOIR HOSE

a.
C459828


Hide 31481 3.DISCONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

a.
C459829N01
0.417,0.031 0.698,0.385 0.281,0.354 18 false i

i.

Using a 10 mm union nut wrench, disconnect the clutch master cylinder to flexible hose tube from the clutch master cylinder assembly.



Hide 31453A 4.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

Hide 31410 5.REMOVE CLUTCH MASTER CYLINDER ASSEMBLY

a.
C459830