Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for Gasoline Model LHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480879 BRAKE BOOSTER(for Gasoline Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for Gasoline Model LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C461304N01
1.74,1.25 2.073,1.25 false 1.615,1.885 1.948,1.885 false 1.604,2.708 1.938,2.708 false 1.26,4.646 1.594,4.646 false 4.385,2.167 4.719,2.167 false 3.167,0.938 3.5,0.938 false 1.083,4.49 1.365,4.844 0.281,0.354 18 false 1 2.906,0.792 3.188,1.146 0.281,0.354 18 false 2 2.135,1.104 2.417,1.458 0.281,0.354 18 false 3 2.021,1.729 2.302,2.083 0.281,0.354 18 false 4 2.01,2.531 2.292,2.885 0.281,0.354 18 false 5 4.802,2.01 5.083,2.365 0.281,0.354 18 false 6 2.865,1.385 3.177,1.583 0.313,0.198 10 false x3 4.146,0.646 4.458,0.844 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE MASTER CYLINDER SUB-ASSEMBLY 47201 - - -
2 ECM 89661 (Click here) - -
3 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
4 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
5 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
6 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -

C461305N01
2.333,2.698 2.333,2.365 false 2.885,4.177 3.219,4.177 false 2.26,2.75 2.542,3.104 0.281,0.354 18 false 8 3.302,4.021 3.583,4.375 0.281,0.354 18 false 7 2.938,4.792 3.25,4.99 0.313,0.198 10 false x9 2.135,5.208 2.448,5.406 0.313,0.198 10 false x4 1.781,5.333 2.094,5.531 0.313,0.198 10 false x4 1.823,2.083 2.135,2.281 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

7 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
8 DASH PANEL HEAT INSULATOR 55225C - - -

C461008N03
2.198,0.917 2.615,0.917 false 1.917,2.667 2.25,2.667 false 6.25,2.844 6.583,2.844 false 2.948,0.792 3.5,1.146 0.552,0.354 18 false 11 2.323,2.531 2.875,2.885 0.552,0.354 18 false 10 6.667,2.698 7.073,3.052 0.406,0.354 18 false 9 6.219,3.167 6.531,3.365 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

9 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
10 COLUMN HOLE COVER SILENCER SHEET 45259A - - -
11 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -

C461306N01
0.604,1.25 0.938,1.25 false 2.01,1.563 2.26,1.094 2.26,1.094 2.427,1.094 false 5.667,1.479 6,1.479 false 3.448,1.833 3.781,1.833 false 4.052,2.396 4.385,2.396 false 4.385,2.781 4.719,2.781 false 4.99,3.583 4.99,3.25 false 2.948,3.104 2.948,2.771 false 2.885,5.5 3.219,5.5 false 1.604,5.375 1.938,5.375 false 1.604,4.094 1.938,4.094 false 1.833,4.083 1.833,4 1.833,4 2.167,4 false 3.51,2.406 3.927,2.906 3.927,2.906 3.927,3.073 false 0.302,1.083 0.771,1.479 0.469,0.396 18 false 15 2.75,0.979 3.708,1.313 0.958,0.333 18 false 20, 23 3.854,1.698 4.26,2 0.406,0.302 18 false 14 4.458,2.229 4.865,2.531 0.406,0.302 18 false 21 4.875,3.625 5.281,3.927 0.406,0.302 18 false 13 5.333,1.313 5.74,1.615 0.406,0.302 18 false 16 2.833,3.135 3.24,3.438 0.406,0.302 18 false 24 1.26,3.917 1.667,4.219 0.406,0.302 18 false 19 1.271,5.219 1.677,5.521 0.406,0.302 18 false 18 3.406,5.354 3.813,5.656 0.406,0.302 18 false 17 2.708,3.177 2.865,3.375 0.156,0.198 10 false ● 1.167,5.271 1.323,5.469 0.156,0.198 10 false ● 3.271,5.396 3.427,5.594 0.156,0.198 10 false ● 3.573,3.104 4.406,3.438 0.833,0.333 18 false 12, 22 4.792,2.667 4.948,2.865 0.156,0.198 10 false ● 3.458,2.719 3.708,2.917 0.25,0.198 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

12 LOOSEN CLEVIS LOCK NUT - - - -
13 BRAKE PEDAL RETURN SPRING 47101A - - -
14 PUSH ROD PIN 47264A - - -
15 UNION TO CHECK VALVE HOSE 44773F - - -
16 ENGINE ROOM MAIN WIRE 82111 - - -
17 NO. 3 BRAKE TUBE CLAMP 47373B - - -
18 NO. 4 BRAKE TUBE CLAMP 47374B - - -
19 BRAKE LINE - (Click here) - -
20 SEPARATE BRAKE BOOSTER ASSEMBLY 44610 (Click here) - -
21 BRAKE MASTER CYLINDER PUSH ROD CLEVIS - - - -
22 REMOVE CLEVIS LOCK NUT - - - -
23 REMOVE BRAKE BOOSTER ASSEMBLY 44610 (Click here) - -
24 BRAKE BOOSTER GASKET 44785 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 47201 1.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 89661 2.REMOVE ECM

Z101186

Click here(Click here)

Hide 3.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 4.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 5.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 6.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 51410 7.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 55225C 8.REMOVE DASH PANEL HEAT INSULATOR

a.
C461296


Hide 55606 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 45259A 10.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 11.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Z101186

Click here(Click here)

Hide 12.LOOSEN CLEVIS LOCK NUT

a.
C430412C03
4.115,0.917 4.448,0.917 true 3.417,1.333 3.583,1.333 3.583,1.333 3.781,0.917 false 4.5,0.865 4.813,1.063 0.313,0.198 10 false *2 3.208,1.26 3.521,1.458 0.313,0.198 10 false *1
*1 Clevis Lock Nut *2 Brake Master Cylinder Push Rod Clevis



Hide 47101A 13.REMOVE BRAKE PEDAL RETURN SPRING

Hide 44773F 15.DISCONNECT UNION TO CHECK VALVE HOSE

a.
C461297


Hide 82111 16.SEPARATE ENGINE ROOM MAIN WIRE

a.
C461298


Hide 47373B 17.REMOVE NO. 3 BRAKE TUBE CLAMP

a.
C461299


Hide 47374B 18.REMOVE NO. 4 BRAKE TUBE CLAMP

a.
C461300


Hide 19.DISCONNECT BRAKE LINE

a.
C461301N01
1.844,0.063 2.125,0.417 0.281,0.354 18 false i

i.

Using a union nut wrench, disconnect the 2 brake lines from the brake actuator assembly.

NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.





Hide 44610 20.SEPARATE BRAKE BOOSTER ASSEMBLY

a.
C461302C01
0.146,0.031 6.927,1.865 6.781,1.833 3.552,1.865 3.552,0.031 false 3.927,0.052 4.208,0.406 0.281,0.354 18 false ii 3.708,2.031 3.99,2.385 0.281,0.354 18 false iv 0.365,1.969 0.646,2.323 0.281,0.354 18 false iii 0.542,0.052 0.823,0.406 0.281,0.354 18 false i 0.208,0.083 0.583,0.323 0.375,0.24 12 false *A 3.625,0.073 4,0.313 0.375,0.24 12 false *B
*A w/o Stop And Start System *B w/ Stop And Start System
V100155

Protective Tape - -


i.

Disconnect the vacuum warning switch connector.


ii.

Disconnect the vacuum sensor connector.


iii.

Apply protective tape to the vehicle body as shown in the illustration.


iv.

Remove the 4 nuts.



Hide 21.REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.
C429018


Hide 22.REMOVE CLEVIS LOCK NUT

a.
C429019


Hide 44610 23.REMOVE BRAKE BOOSTER ASSEMBLY

Z101186

NOTICE:

Do not apply excessive force to the brake lines.



a.
C461303N01
0.365,0 1.74,0.354 1.375,0.354 18 false i, ii

i.

Move aside the front No. 1 brake tube and front No. 2 brake tube as shown in the illustration.


ii.

Remove the brake booster assembly.



Hide 44785 24.REMOVE BRAKE BOOSTER GASKET

a.
C429011