Home › Drivetrain › CLUTCH › CLUTCH STROKE SENSOR (for LHD) › from 2021.07
RM3700E _52 Drivetrain _104786 CLUTCH _0480195 CLUTCH STROKE SENSOR(for LHD) A

CLUTCH  CLUTCH STROKE SENSOR(for LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C459846N01
3.073,0.917 4.083,1.104 1.01,0.188 3.031,0.875 4.125,1.146 1.094,0.271 2.646,1.448 2.5,1.448 2.5,1.448 2.5,0.875 false 3.927,0.26 3.708,0.26 3.708,0.26 3.385,0.521 false 3.073,1.01 2.927,1.01 2.927,1.01 2.927,0.708 false 4.927,2.281 4.927,2.021 false 6.823,0.25 6.521,0.25 false 6.854,0.625 6.521,0.625 false 6.792,1.031 6.531,1.031 false 2.958,1.26 4.063,1.615 1.104,0.354 18 false 1, 3 4.25,0.083 5.354,0.438 1.104,0.354 18 false 4 3.115,0.927 4.052,1.167 0.938,0.24 8 false 8.5 (87, 75 in.*lbf) 4.865,2.292 5.969,2.646 1.104,0.354 18 false 5 3,0.563 3.313,0.76 0.313,0.198 10 false x2 6.365,2.146 6.677,2.344 0.313,0.198 10 false x2 6.323,0.073 6.552,0.448 0.229,0.375 18 false 2 6.323,0.458 6.552,0.833 0.229,0.375 18 false 6 6.333,0.854 6.563,1.229 0.229,0.375 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSTALL CLUTCH PEDAL STROKE SENSOR ASSEMBLY 89280 (Click here) - -
2 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 ADJUST CLUTCH PEDAL STROKE SENSOR ASSEMBLY 89280 (Click here) - -
4 BRAKE PEDAL RETURN SPRING 47101A (Click here) - -
5 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
6 CHECK AND CLEAR DTC - (Click here) - -
7 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) - -

PROCEDURE

Hide 89280 1.INSTALL CLUTCH PEDAL STROKE SENSOR ASSEMBLY

a.

When installing a new clutch pedal stroke sensor assembly:

C459847C01
0.479,1.448 0.604,1.448 0.604,1.448 0.708,1.26 true 1.229,1.792 1.104,1.792 1.104,1.792 0.781,2.188 true 0.49,0.938 0.656,0.938 0.656,0.938 0.75,1.115 true 0.302,0.813 0.469,0.979 0.167,0.167 10 true *a 0.302,1.333 0.49,1.5 0.188,0.167 10 true *b 1.26,1.677 1.427,1.833 0.167,0.156 10 true *c 0.427,0.042 1.625,0.333 1.198,0.292 18 false i, iii, iv 4.094,0.031 5.292,0.323 1.198,0.292 18 false ii
*a Clutch Pedal Stroke Sensor Assembly Lever *b Clutch Pedal Groove
*c Clutch Pedal Stroke Sensor Assembly Lever Set Pin - -


NOTICE:

Do not break the clutch pedal stroke sensor assembly lever set pin before being instructed to do so.


i.

Install a new clutch pedal stroke sensor assembly to the pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Engage the clutch pedal stroke sensor assembly lever with the clutch pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the clutch pedal stroke sensor assembly.

·

Check that the tip of the clutch pedal stroke sensor assembly lever is protruding from the clutch pedal groove.

·

Do not drop the clutch pedal stroke sensor assembly.

·

If the clutch pedal stroke sensor assembly has been dropped, replace the clutch pedal stroke sensor assembly with a new one.

·

Do not subject the clutch pedal stroke sensor assembly to shock during installation.

·

Make sure to confirm that the clutch pedal fully returns to its original position.




ii.

Connect the clutch pedal stroke sensor assembly connector.


iii.

Firmly depress the clutch pedal sub-assembly to break the clutch pedal stroke sensor assembly lever set pin.


iv.

Remove the broken clutch pedal stroke sensor assembly lever set pin.



b.

When reusing the clutch pedal stroke sensor assembly:

C459848C01
0.469,1.365 0.635,1.365 0.635,1.365 0.677,1.198 true 0.479,0.885 0.646,0.885 0.646,0.885 0.729,1.052 true 0.313,0.771 0.479,0.927 0.167,0.156 10 true *a 0.313,1.26 0.479,1.417 0.167,0.156 10 true *b 0.427,0.031 3.177,0.385 2.75,0.354 18 false i 4.073,0.052 4.729,0.406 0.656,0.354 18 false ii
*a Clutch Pedal Stroke Sensor Assembly Lever *b Clutch Pedal Groove


i.

Install the clutch pedal stroke sensor assembly to the pedal support assembly and temporarily tighten the 2 nuts.

NOTICE:
·

Engage the clutch pedal stroke sensor assembly lever with the clutch pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the clutch pedal stroke sensor assembly.

·

Check that the tip of the clutch pedal stroke sensor assembly lever is protruding from the clutch pedal groove.

·

Do not drop the clutch pedal stroke sensor assembly.

·

If the clutch pedal stroke sensor assembly has been dropped, replace the clutch pedal stroke sensor assembly with a new one.

·

Do not subject the clutch pedal stroke sensor assembly to shock during installation.

·

Make sure to confirm that the clutch pedal fully returns to its original position.



HINT:

When fully tightening the nuts, perform adjust clutch pedal stroke sensor assembly first.



ii.

Connect the clutch pedal stroke sensor assembly connector.



Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89280 3.ADJUST CLUTCH PEDAL STROKE SENSOR ASSEMBLY

Z101186

NOTICE:

When the clutch pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.



a.
C459849N01
0.417,0.021 0.573,0.323 0.156,0.302 18 true i 3.938,0.021 4.448,0.354 0.51,0.333 18 true ii 1.771,2.021 2.031,2.396 0.26,0.375 18 true iii

i.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display
Clutch Stroke Sensor Voltage
50003 372 607

ii.

Read the clutch stroke sensor voltage value in the Data List, and turn the clutch pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (clutch pedal fully released):

0.96 to 1.04 V



iii.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

After turning the ignition switch to ON, do not depress the clutch pedal sub-assembly until the nuts have been tightened.




Hide 47101A 4.INSTALL BRAKE PEDAL RETURN SPRING

Z101186

Click here(Click here)

Hide 55606 5.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 7. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART