When the seat heater switch is operated, the power distribution box assembly receives the signal. The power distribution box assembly receives the signal and operates the front seat heater.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the auxiliary battery voltage is low, the seat heater system may not operate. When "High Power Consumption Partial Limit On AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the auxiliary battery, referring to On-vehicle Inspection for the charging system.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat A/C System No.2 Input Signal | Front LH side seat heater drive signal (Input) | OFF/ON | OFF: Seat heater switch LH off
ON: Seat heater switch LH on |
- |
| Tester Display |
|---|
| Seat A/C System No.2 Input Signal |
The GTS display changes correctly in response to the seat heater switch LH condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O58 front seat cushion heater assembly LH connector.
Disconnect the 4C power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O58)Location & Routingewd_type=routing;type=c;code=O58 Click Connector(O58)Seat>Floor Wire>Front Seat Cushion Heater Assembly LHewd_type=component;type=c;code=O58;pinno=7,5 |
||
| O58-7 (LO) - 4C-39 | Always | Below 1 Ω |
| O58-7 (LO) - body ground | Always | 10 kΩ or higher |
| O58-5 (E) - body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
OK
NG
Disconnect the 4B power distribution box assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-6 - Body ground | Seat heater switch RH on | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4C power distribution box assembly connector.
Disconnect the H52 seat heater switch LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H52)Location & Routingewd_type=routing;type=c;code=H52 Click Connector(H52)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch LHewd_type=component;type=c;code=H52;pinno=2 |
||
| 4B-6 - H52-2 (LO) | Always | Below 1 Ω |
| 4B-6 - body ground | Always | 10 kΩ or higher |
| 4C-25 - body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H52)Location & Routingewd_type=routing;type=c;code=H52 Click Connector(H52)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch LHewd_type=component;type=c;code=H52;pinno=5 |
||
| H52-5 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| H52-5 (IG) - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H52)Location & Routingewd_type=routing;type=c;code=H52 Click Connector(H52)Instrument Panel>Instrument Panel Wire / Speaker Wire>Seat Heater Switch LHewd_type=component;type=c;code=H52;pinno=4 |
||
| H52-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG