| ● | Non-reusable part | ★ | Precoated part |
| *1 | SHIFT AND SELECT LEVER SHAFT WITH HEAD STRAIGHT SCREW PLUG | *2 | SHIFT AND SELECT LEVER SHAFT COMPRESSION SPRING |
| *3 | SHIFT DETENT BALL PLUG | *4 | SHIFT DETENT BALL COMPRESSION SPRING |
| *5 | REVERSE IDLER THRUST WASHER | *6 | REVERSE IDLER GEAR SHAFT |
| ● | Non-reusable part | ★ | Precoated part |
| *1 | REVERSE SHIFT FORK SLOTTED SPRING PIN | *2 | NO. 4 GEAR SHIFT FORK SHAFT |
| *3 | SHIFT INTER LOCK PLATE | *4 | INNER SELECT LEVER SET BOLT |
| *5 | INNER SELECT LEVER | - | - |
| ● | Non-reusable part | ★ | Precoated part |
| *1 | SHIFT HEAD SLOTTED PIN | *2 | NO. 1 GEAR SHIFT FORK ASSEMBLY |
| *3 | NO. 2 GEAR SHIFT FORK ASSEMBLY | *4 | SHIFT FORK SHAFT SNAP RING |
| *5 | NO. 2 REVERSE PRE-BALK HEAD SPACER | *6 | NO. 2 REVERSE PRE-BALK HEAD STRAIGHT PIN |
| *7 | NO. 2 REVERSE PRE-BALK HEAD TORSION SPRING | *8 | SHIFT FORK SHAFT STOPPER SLOTTED PIN |
| *9 | NO. 3 GEAR SHIFT FORK ASSEMBLY | *10 | SLOTTED SPRING PIN |
| *11 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) | *12 | FRONT DIFFERENTIAL CASE REAR SHIM |
| *13 | FRONT DIFFERENTIAL CASE FRONT PLATE WASHER | *14 | FRONT TRANSAXLE (MTM) CASE |
| ● | Non-reusable part | - | - |
| *1 | OUTPUT SHAFT COVER | - | - |
| ● | Non-reusable part | - | - |
| *1 | REAR OUTPUT SHAFT BEARING SHIM | *2 | INNER SHIFT LEVER SLOTTED SPRING PIN |
| *3 | INNER NO. 1 SHIFT LEVER | *4 | OUTER SHIFT LEVER SPACER |
| ● | Non-reusable part | - | - |
33101A
1.REMOVE MANUAL TRANSMISSION FILLER PLUG
33101B
2.REMOVE MANUAL TRANSMISSION DRAIN PLUG
89413B
3.REMOVE TRANSMISSION REVOLUTION SENSOR
84210
4.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY
Using a 27 mm deep socket wrench, remove the back-up light switch assembly and gasket from the manual transmission case.
84545
5.REMOVE NEUTRAL POSITION SWITCH
Using SST, remove the neutral position switch and gasket from the manual transmission case.
335A0
6.REMOVE CONTROL CABLE BRACKET ASSEMBLY
7.REMOVE WIRE HARNESS CLAMP BRACKET
31121
8.REMOVE NO. 1 CLUTCH HOUSING COVER
31478
9.REMOVE RELEASE CYLINDER BLEEDER PLUG CAP
10.REMOVE RELEASE CYLINDER BLEEDER PLUG
31126B
12.REMOVE CLUTCH TUBE BOOT
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
30300
15.SECURE MANUAL TRANSAXLE ASSEMBLY
| *a | Wooden Block | - | - |
33290
16.REMOVE NO. 1 LOCK BALL ASSEMBLY
33451H
17.REMOVE REVERSE IDLER GEAR SHAFT BOLT
33292A
18.REMOVE LOCK BALL PIN
Using a 10 mm hexagon socket wrench, remove the shift and select lever shaft with head straight screw plug from the manual transmission case.
Using a magnet hand, remove the shift and select lever shaft compression spring and lock ball pin from the manual transmission case.
33275C
19.REMOVE SHIFT DETENT BALL
Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the manual transmission case.
Using a magnet hand, remove the shift detent ball compression spring and shift detent ball from the manual transmission case.
Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case.
Using a magnet hand, remove the 2 shift detent ball compression springs and 2 shift detent balls from the manual transmission case.
33253F
20.REMOVE OUTER SHIFT LEVER E-RING
33111
21.REMOVE MANUAL TRANSMISSION CASE
| *a | Boss | - | - |
|
Turn |
|
Push |
|
Remove in this Direction | - | - |
Remove the 16 bolts.
Using a screwdriver with its tip wrapped with protective tape, separate the manual transmission case from the front transaxle (MTM) case.
Do not damage the manual transmission case and front transaxle (MTM) case.
Turn the outer No. 1 shift lever clockwise until it comes into contact with the boss.
Push the outer No. 1 shift lever and remove the manual transmission case.
33402
22.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft from the front transaxle (MTM) case as shown in the illustration.
23.REMOVE REVERSE SHIFT FORK SHAFT ASSEMBLY
|
Turn |
|
Remove in this Direction |
Turn the reverse shift fork shaft assembly clockwise.
Remove reverse shift fork shaft assembly from the front transaxle (MTM) case.
33211
24.REMOVE REVERSE SHIFT FORK
Secure the No. 4 gear shift fork shaft in a vise between aluminum plates.
Do not overtighten the vise.
Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the reverse shift fork.
Remove the reverse shift fork from the No. 4 gear shift fork shaft.
33240
25.REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY
26.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY
| *1 | Shift and Select Lever Shaft Assembly | *2 | Shift Inter Lock Plate |
|
Turn | - | - |
Using a 6 mm hexagon socket wrench, remove the inner select lever set bolt.
Turn the shift and select lever shaft assembly clockwise and remove it from the front transaxle (MTM) case.
Remove the shift inter lock plate from the front transaxle (MTM) case.
33257
27.REMOVE OUTER SELECT LEVER
33257C
28.REMOVE OUTER SELECT LEVER OIL SEAL
|
|
Using a screwdriver with its tip wrapped with protective tape, remove the outer select lever oil seal from the front transaxle (MTM) case.
29.REMOVE INPUT SHAFT ASSEMBLY
33232F
30.REMOVE NO. 1 GEAR SHIFT HEAD
Secure the No. 1 gear shift fork assembly in a vise between aluminum plates.
Do not overtighten the vise.
Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 1 gear shift head.
Remove the No. 1 gear shift head from the No. 1 gear shift fork assembly.
33233A
31.REMOVE NO. 2 GEAR SHIFT HEAD
Secure the No. 2 gear shift fork assembly in a vise between aluminum plates.
Do not overtighten the vise.
Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 2 gear shift head.
Remove the No. 2 gear shift head from the No. 2 gear shift fork assembly.
33238A
32.REMOVE NO. 2 REVERSE PRE-BALK HEAD
| *1 | SHIFT FORK SHAFT SNAP RING | - | - |
Using 2 screwdrivers with their tips wrapped with protective tape and a hammer, remove the shift fork shaft snap ring from the No. 2 gear shift fork assembly.
Use a piece of cloth to keep the shift fork shaft snap ring from flying off.
Remove the No. 2 reverse pre-balk head spacer from the No. 2 gear shift fork assembly.
Remove the No. 2 reverse pre-balk head from the No. 2 gear shift fork assembly.
33.REMOVE NO. 2 REVERSE PRE-BALK HEAD BIMETAL FORMED BUSHING
| *1 | No. 2 Reverse Pre-balk Head Bimetal Formed Bushing | - | - |
Secure the No. 2 reverse pre-balk head in a vise between aluminum plates.
Do not overtighten the vise.
Using a 3 mm pin punch and a hammer, remove the No. 2 reverse pre-balk head straight pin from the No. 2 reverse pre-balk head.
Secure the No. 2 reverse pre-balk head in a vise between aluminum plates.
Do not overtighten the vise.
Using a screwdriver with its tip wrapped with protective tape and a hammer, remove the 2 No. 2 reverse pre-balk head bimetal formed bushings from the No. 2 reverse pre-balk head.
Do not damage the No. 2 reverse pre-balk head.
33291A
34.REMOVE SHIFT FORK SHAFT STOPPER
Secure the No. 2 gear shift fork assembly in a vise between aluminum plates.
Do not overtighten the vise.
Remove the No. 2 reverse pre-balk head torsion spring from the No. 2 gear shift fork assembly.
Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the shift fork shaft stopper.
Remove the shift fork shaft stopper from the No. 2 gear shift fork assembly.
33234A
35.REMOVE NO. 3 GEAR SHIFT HEAD
Secure the No. 3 gear shift fork assembly in a vise between aluminum plates.
Do not overtighten the vise.
Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 3 gear shift head.
Remove the No. 3 gear shift head from the No. 3 gear shift fork assembly.
33239
36.REMOVE NO. 3 REVERSE PRE-BALK HEAD
Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 3 reverse pre-balk head.
Remove the No. 3 reverse pre-balk head from the No. 3 gear shift fork assembly.
41300
37.REMOVE FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY
41311E
38.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
| *a | Hold | - | - |
|
Turn | - | - |
Using SST, remove the front differential case front tapered roller bearing (outer race) and front differential case front plate washer from the front transaxle (MTM) case.
Using SST, remove the front differential case front tapered roller bearing (inner race) from the front differential case with ring gear assembly.
41311F
39.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
| *a | Hold | - | - |
|
Turn | - | - |
Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear shim from the manual transmission case.
Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case with ring gear assembly.
33449B
40.REMOVE TRANSMISSION MAGNET
33176D
41.REMOVE NO. 2 TRANSMISSION OIL SEPARATOR
33101J
42.REMOVE BREATHER PLUG
33321N
43.REMOVE FRONT OUTPUT SHAFT BEARING (OUTER RACE)
Using SST, remove the front output shaft bearing (outer race) from the front transaxle (MTM) case.
Remove the output shaft cover from the front transaxle (MTM) case.
31105D
44.REMOVE FRONT TRANSAXLE CASE OIL SEAL
Using SST and a hammer, remove the front transaxle case oil seal from the front transaxle (MTM) case.
43410M
45.REMOVE FRONT DRIVE SHAFT OIL SEAL RH
Using SST and a hammer, remove the front drive shaft oil seal RH from the front transaxle (MTM) case.
33280
46.REMOVE REVERSE RESTRICT PIN ASSEMBLY
33111J
47.REMOVE MANUAL TRANSMISSION CASE STRAIGHT PIN
33321A
48.REMOVE REAR OUTPUT SHAFT BEARING (OUTER RACE)
Using SST, remove the rear output shaft bearing (outer race) and rear output shaft bearing shim from the manual transmission case.
33311K
49.REMOVE REAR INPUT SHAFT BEARING SHIM
33137
50.REMOVE INPUT SHAFT COVER
33124C
51.REMOVE NO. 1 OIL RECEIVER PIPE
33176B
52.REMOVE TRANSMISSION OIL SEPARATOR
33109C
53.REMOVE MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY
33253
54.REMOVE OUTER NO. 1 SHIFT LEVER
Using a 5 mm pin punch and hammer, remove the inner shift lever slotted spring pin from the inner No. 1 shift lever.
When removing the inner shift lever slotted spring pin, align the inner shift lever slotted spring pin with the hole in the No. 1 lock ball assembly.
Remove the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever from the manual transmission case.
33253H
55.REMOVE OUTER SHIFT LEVER OIL SEAL
|
|
Using a screwdriver with its tip wrapped with protective tape, remove the outer shift lever oil seal from the manual transmission case.
43420H
56.REMOVE FRONT DRIVE SHAFT OIL SEAL LH
Using SST and a hammer, remove the front drive shaft oil seal LH from the manual transmission case.