Home › Drivetrain › CLUTCH › CLUTCH UNIT › from 2021.07
RM3700E _52 Drivetrain _104786 CLUTCH _0480197 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C459852N01
5.729,2.979 6.063,2.979 false 1.604,3.167 2.031,3.167 false 5.708,1.26 6.042,1.26 false 5.25,0.479 5.042,0.479 5.042,0.479 5.042,0.875 false 6.125,2.802 6.406,3.156 0.281,0.354 18 false 1 1.406,3 1.688,3.354 0.281,0.354 18 false 2 6.406,1.104 6.688,1.458 0.281,0.354 18 false 3 5.313,0.333 5.594,0.688 0.281,0.354 18 false 4 5.76,0.458 6.073,0.656 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 MANUAL TRANSAXLE ASSEMBLY 30300 - - -
2 CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE 31482 (Click here) - -
3 CLUTCH RELEASE BLEEDER SUB-ASSEMBLY 31407B (Click here) - -
4 CLUTCH TUBE BOOT 31126B - - -

C459856N01
3.531,0.521 3.667,0.313 3.667,0.313 3.917,0.313 false 3.417,1.552 3.698,1.552 3.698,1.552 3.75,1.281 false 2.969,4.094 2.969,3.729 false 1.99,3.323 1.99,2.99 false 2.771,0.885 3.052,0.885 false 3.229,1.396 3.719,1.698 0.49,0.302 18 false 5 4.333,0.146 4.823,0.448 0.49,0.302 18 false 6 3.052,4.115 3.542,4.417 0.49,0.302 18 false 7 1.927,3.344 2.24,3.542 0.313,0.198 10 false *1 3.729,3.969 4.042,4.167 0.313,0.198 10 false x6 3.073,0.979 3.385,1.177 0.313,0.198 10 false x3 3.063,1.469 3.292,1.667 0.229,0.198 10 false ● 2.51,0.781 2.885,0.979 0.375,0.198 10 false ●★

Procedure Part Name Code
Z101186

Z101188

Z101187

5 CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY 31400 (Click here) - -
6 BLEEDER CLUTCH RELEASE TUBE 31483 (Click here) - -
7 CLUTCH COVER ASSEMBLY 31210 (Click here) - -

*1 CLUTCH DISC ASSEMBLY - -
● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the manual transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.



NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 31482 2.REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

a.
C462153N01
0.417,0.042 0.865,0.292 0.448,0.25 18 true i, ii 4.167,0.021 4.583,0.271 0.417,0.25 18 true iii

i.

Using a 10 mm union nut wrench, separate the clutch release cylinder to flexible hose tube from the clutch release bleeder sub-assembly.


ii.

Remove the bolt and clutch release cylinder to flexible hose tube from the manual transaxle assembly.


iii.

Remove the clamp from the clutch release cylinder to flexible hose tube.



Hide 31407B 3.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C462154N01
0.406,0.031 0.542,0.323 0.135,0.292 18 true i 4,0.031 4.177,0.302 0.177,0.271 18 true ii

i.

Using a 10 mm union nut wrench, separate the clutch release bleeder sub-assembly from the bleeder clutch release tube.


ii.

Remove the 2 bolts and clutch release bleeder sub-assembly from the manual transaxle assembly.



Hide 31126B 4.REMOVE CLUTCH TUBE BOOT

a.
C459853


Hide 31400 5.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

a.
C461140N01
0.427,0.042 0.573,0.375 0.146,0.333 18 true i

i.

Remove the 3 bolts and clutch release cylinder with bearing assembly together with bleeder clutch release tube from the manual transaxle assembly.



Hide 31483 6.REMOVE BLEEDER CLUTCH RELEASE TUBE

a.
C461141N01
0.427,0.021 1.177,0.448 0.75,0.427 18 false i, ii

i.

Mount the clutch release cylinder with bearing assembly in a soft jaw vise.


ii.

Using a 10 mm union nut wrench, remove the bleeder clutch release tube from the clutch release cylinder with bearing assembly.



Hide 31210 7.REMOVE CLUTCH COVER ASSEMBLY

a.
C459857C02
3.094,1.24 2.896,1.51 2.896,1.51 3.156,1.229 true 2.76,1.479 3.073,1.677 0.313,0.198 10 false *a 0.427,0.021 1.313,0.469 0.885,0.448 18 false i, ii, iii
*a Matchmark - -


i.

Put matchmarks on the clutch cover assembly and the flywheel sub-assembly.


ii.

Loosen each bolt 180° at a time until the spring tension is released.


iii.

Remove the 6 bolts and pull off the clutch cover assembly.

NOTICE:
·

Do not drop the clutch disc assembly.

·

Keep the lined part of the clutch disc assembly, the pressure plate, and the surface of the flywheel sub-assembly away from oil and foreign matter.