Home › Drivetrain › EC6D (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE UNIT › from 2021.07
RM3700E _52 Drivetrain _104886 EC6D MANUAL TRANSMISSION / TRANSAXLE _0480440 MANUAL TRANSAXLE UNIT A

EC6D MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C461145N01
4.969,2.771 5.833,3.542 0.865,0.771 3.323,1.813 4.094,2.51 0.771,0.698 0.146,0.74 0.927,0.927 0.781,0.188 3.51,5.271 4.313,5.469 0.802,0.198 4.313,5.365 4.708,5.365 false 0.552,0.74 0.552,0.479 false 2.219,3.208 2.385,3.208 2.385,3.208 2.5,3.01 false 2.281,3.656 2.448,3.656 2.448,3.656 2.729,3.188 true 2.99,4.073 3.219,4.073 3.219,4.073 3.448,3.656 true 3.76,4.542 4,4.542 4,4.542 4.25,4.083 true 4.135,5.01 4.771,5.01 false 4.656,3.99 4.802,3.75 4.802,3.75 4.969,3.75 false 6.198,3.51 6.594,3.51 false 5.375,2.771 5.552,2.25 5.552,2.25 5.802,2.25 false 4.656,2.219 4.865,1.729 4.865,1.729 5.115,1.729 false 3.698,1.813 3.865,1.292 3.865,1.292 4.135,1.292 false 3.104,2.25 3.104,1.99 false 6.448,0.24 6.844,0.24 false 3.406,4.344 3.792,4.708 0.385,0.365 18 false 10 5.115,0.052 6.583,0.427 1.469,0.375 18 false 3, 6, 11, 15 4.667,1.094 4.865,1.406 0.198,0.313 18 false 1 4.51,1.188 4.698,1.396 0.188,0.208 10 false ● 5.521,1.542 7.083,1.854 1.563,0.313 18 false 4, 8, 12, 18 6.188,2.146 6.375,2.354 0.188,0.208 10 false ● 6.354,2.063 6.552,2.375 0.198,0.313 18 false 2 2.063,3.469 2.26,3.781 0.198,0.313 18 false 9 1.896,3.563 2.083,3.771 0.188,0.208 10 false ● 2.229,3.917 3.365,4.208 1.135,0.292 18 false 13, 17 3.271,4.438 3.458,4.646 0.188,0.208 10 false ● 2.823,4.833 4.76,5.156 1.938,0.323 18 false 5, 7, 14, 16 6.635,3.406 6.823,3.615 0.188,0.208 10 false *2 5.01,3.646 5.219,3.844 0.208,0.198 10 false *4 2.052,3.104 2.26,3.302 0.208,0.198 10 false *3 3.042,2.25 3.323,2.458 0.281,0.208 10 false *1 0.656,0.302 0.865,0.5 0.208,0.198 10 false x2 4.698,5.375 4.979,5.573 0.281,0.198 10 false x14 0.177,0.75 1.156,0.979 0.979,0.229 8 false 29.4 (300, 22) 3.563,5.281 4.354,5.427 0.792,0.146 8 false 29.4 (300, 22)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING 41311E (Click here) - -
2 FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING 41311F (Click here) - -
3 CLEAN TRANSMISSION CASE - (Click here) - -
4 INSTALL FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY 41300 (Click here) - -
5 INSTALL MANUAL TRANSMISSION CASE 33111 - - -
6 ADJUST DIFFERENTIAL SIDE BEARING PRELOAD - (Click here) - -
7 REMOVE MANUAL TRANSMISSION CASE 33111 - - -
8 REMOVE FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY 41300 - - -
9 FRONT OUTPUT SHAFT BEARING (OUTER RACE) 33321N (Click here) - -
10 REAR OUTPUT SHAFT BEARING (OUTER RACE) 33321A (Click here) - -
11 CLEAN TRANSMISSION CASE - (Click here) - -
12 INSTALL FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY 41300 - - -
13 INSTALL OUTPUT SHAFT ASSEMBLY - (Click here) - -
14 INSTALL MANUAL TRANSMISSION CASE 33111 - - -
15 ADJUST OUTPUT SHAFT BEARING PRELOAD - (Click here) - -
16 REMOVE MANUAL TRANSMISSION CASE 33111 - - -
17 REMOVE OUTPUT SHAFT ASSEMBLY - - - -
18 REMOVE FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY 41300 - - -

*1 FRONT DIFFERENTIAL CASE FRONT PLATE WASHER *2 FRONT DIFFERENTIAL CASE REAR SHIM
*3 OUTPUT SHAFT COVER *4 REAR OUTPUT SHAFT BEARING SHIM
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

Gear Oil
● Non-reusable part - -

C462173N01
2.156,0.094 2.833,0.271 0.677,0.177 2.677,4.396 3.365,4.583 0.688,0.188 3.792,3.292 4.5,3.49 0.708,0.198 4.323,1.115 7.104,2.583 2.781,1.469 3.104,0.177 2.833,0.177 false 3.667,4.49 3.365,4.49 false 3.302,0.594 3.031,0.594 false 3.229,1.573 3.031,1.573 false 1.927,0.563 1.656,0.563 false 1.479,1.063 1.125,1.063 false 0.677,3.667 0.677,3.99 false 3.531,3.719 3.229,3.719 false 4.042,4.74 4.042,5.115 false 6.5,2.906 6.177,2.906 false 6.479,2.406 6.177,2.406 false 4.573,1.615 4.573,1.906 false 5.052,1.99 5.052,2.281 false 3.792,3.396 3.625,3.396 3.625,3.396 3.625,3.156 false 6.188,0.573 5.938,0.573 5.938,0.573 5.698,1.115 false 5.833,2.719 6.198,3.01 0.365,0.292 18 false 19 5.708,2.813 5.917,3 0.208,0.188 10 false ● 6.552,0.396 6.917,0.688 0.365,0.292 18 false 20 4.073,5.073 4.438,5.365 0.365,0.292 18 false 21 0.854,3.979 1.219,4.271 0.365,0.292 18 false 22 0.802,0.885 1.167,1.177 0.365,0.292 18 false 24 1.323,0.396 1.688,0.688 0.365,0.292 18 false 23 2.708,0.417 3.073,0.708 0.365,0.292 18 false 25 2.708,1.396 3.073,1.688 0.365,0.292 18 false 26 3.604,3.552 3.969,3.844 0.365,0.292 18 false 27 4.51,1.917 4.771,2.135 0.26,0.219 10 false *1 4.99,2.292 5.25,2.51 0.26,0.219 10 false *2 6,2.302 6.26,2.521 0.26,0.219 10 false *3 3.833,3.313 4.698,3.542 0.865,0.229 8 false 17 (173, 13) 2.708,4.396 3.542,4.604 0.833,0.208 8 false 17 (173, 13) 2.188,0.094 3.094,0.354 0.906,0.26 8 false 17 (173, 13) 3.24,0.073 3.5,0.292 0.26,0.219 10 false x2 0.771,3.573 1.031,3.792 0.26,0.219 10 false x5 3.792,4.365 4.104,4.563 0.313,0.198 10 false x3 3.698,3.021 4.01,3.219 0.313,0.198 10 false x4 0.708,4.052 0.917,4.24 0.208,0.188 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

19 OUTER SHIFT LEVER OIL SEAL 33253H (Click here) - -
20 OUTER NO. 1 SHIFT LEVER 33253 (Click here) - -
21 MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY 33109C (Click here) - -
22 MANUAL TRANSMISSION CASE STRAIGHT PIN 33111J (Click here) - -
23 REVERSE RESTRICT PIN ASSEMBLY 33280 - - -
24 BREATHER PLUG 33101J (Click here) - -
25 TRANSMISSION OIL SEPARATOR 33176B (Click here) - -
26 NO. 1 OIL RECEIVER PIPE 33124C (Click here) - -
27 NO. 2 TRANSMISSION OIL SEPARATOR 33176D - - -

*1 INNER SHIFT LEVER SLOTTED SPRING PIN *2 INNER NO. 1 SHIFT LEVER
*3 OUTER SHIFT LEVER SPACER - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

C462174N01
0.531,0.875 0.531,0.542 false 4.813,0.823 4.99,0.396 4.99,0.396 5.24,0.396 false 4.708,1.542 4.885,1.542 4.885,1.542 5.021,1.219 false 4.552,2.25 4.219,2.25 false 2.99,2.417 2.604,2.417 false 0.625,0.885 1.177,1.24 0.552,0.354 18 false 28 0.49,0.969 1.042,1.323 0.552,0.354 10 false ● 2.271,2.25 2.698,2.583 0.427,0.333 18 false 29 4.625,2.083 5.177,2.438 0.552,0.354 18 false 30 4.385,1.354 4.938,1.708 0.552,0.354 18 false 31 5.583,0.229 6.135,0.583 0.552,0.354 18 false 32

Procedure Part Name Code
Z101186

Z101188

Z101187

28 FRONT TRANSAXLE CASE OIL SEAL 31105D (Click here) - -
29 TRANSMISSION MAGNET 33449B (Click here) - -
30 INSTALL FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY 41300 - - -
31 INPUT SHAFT COVER 33137 (Click here) - -
32 REAR INPUT SHAFT BEARING SHIM 33311K (Click here) - -

V100135

MP Grease ● Non-reusable part

C462166N01
2.406,1.5 3.021,2.26 0.615,0.76 3.125,1.677 4.521,3.323 1.396,1.646 4.625,2.74 5.885,3.625 1.26,0.885 1.323,2.833 2.229,3.615 0.906,0.781 2.281,3.167 2.917,4.354 0.635,1.188 5.01,0.802 5.906,1.531 0.896,0.729 2.563,2.031 2.563,1.729 false 3.25,2.313 3.25,2.01 false 3.521,2.469 3.521,2.167 false 4.313,2.198 4.25,1.969 4.25,1.969 4.083,1.969 false 3.729,2.906 3.729,2.271 false 3.74,2.781 4.365,2.781 4.365,2.781 4.365,2.625 false 2.583,4.115 2.583,3.813 false 2,3.427 1.698,3.427 false 4.979,3.302 4.979,3 false 5.708,3.198 5.646,2.969 5.646,2.969 5.479,2.969 false 6.448,2.292 6.448,1.99 false 5.573,1 5.271,1 false 2.698,2.542 2.698,2.26 false 4.896,2.344 4.521,2.344 false 5.24,3.865 5.24,3.625 false 4.198,4.219 3.896,4.219 false 6.25,1.146 5.906,1.146 false 1.323,3.219 0.885,3.219 false 2.281,3.979 2.031,3.979 false 6.698,4.302 6.698,4 false 1.708,3.802 2.063,4.125 0.354,0.323 18 false 33 0.563,3.063 0.917,3.385 0.354,0.323 18 false 34 2.75,2.49 3.104,2.813 0.354,0.323 18 false 38 3.802,2.875 4.156,3.198 0.354,0.323 18 false 36 3.667,2.958 4.021,3.281 0.354,0.323 10 false ● 5.271,3.844 5.625,4.167 0.354,0.323 18 false 35 5.25,2.146 5.604,2.469 0.354,0.323 18 false 37 6.604,0.969 6.958,1.292 0.354,0.323 18 false 39 1.531,3.323 1.76,3.51 0.229,0.188 10 false *1 2.469,4.125 2.802,4.313 0.333,0.188 10 false *10 4.24,4.115 4.469,4.302 0.229,0.188 10 false *9 4.917,3.313 5.146,3.5 0.229,0.188 10 false *7 5.313,2.865 5.542,3.052 0.229,0.188 10 false *8 3.188,2.313 3.417,2.5 0.229,0.188 10 false *4 3.469,2.469 3.698,2.656 0.229,0.188 10 false *5 2.5,2.042 2.729,2.229 0.229,0.188 10 false *1 3.917,1.875 4.146,2.063 0.229,0.188 10 false *6 5.625,0.885 5.854,1.073 0.229,0.188 10 false *1 6.396,2.302 6.625,2.49 0.229,0.188 10 false *2 6.635,4.313 6.865,4.5 0.229,0.188 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

33 NO. 3 REVERSE PRE-BALK HEAD 33239 (Click here) - -
34 NO. 3 GEAR SHIFT HEAD 33234A (Click here) - -
35 SHIFT FORK SHAFT STOPPER 33291A (Click here) - -
36 NO. 2 REVERSE PRE-BALK HEAD BIMETAL FORMED BUSHING - (Click here) - -
37 NO. 2 REVERSE PRE-BALK HEAD 33238A (Click here) - -
38 NO. 2 GEAR SHIFT HEAD 33233A (Click here) - -
39 NO. 1 GEAR SHIFT HEAD 33232F (Click here) - -

*1 SHIFT HEAD SLOTTED PIN *2 NO. 1 GEAR SHIFT FORK ASSEMBLY
*3 NO. 2 GEAR SHIFT FORK ASSEMBLY *4 SHIFT FORK SHAFT SNAP RING
*5 NO. 2 REVERSE PRE-BALK HEAD SPACER *6 NO. 2 REVERSE PRE-BALK HEAD STRAIGHT PIN
*7 NO. 2 REVERSE PRE-BALK HEAD TORSION SPRING *8 SHIFT FORK SHAFT STOPPER SLOTTED PIN
*9 NO. 3 GEAR SHIFT FORK ASSEMBLY *10 SLOTTED SPRING PIN
● Non-reusable part - -

C462175N01
0.656,3.146 1.365,3.323 0.708,0.177 2.833,0.875 5.229,1.813 2.396,0.938 1.896,0.938 2.719,1.365 0.823,0.427 0.323,3.615 2.385,4.969 2.063,1.354 2.833,4.198 4.729,5.25 1.896,1.052 3.188,0.927 3.865,1.104 0.677,0.177 2.521,1.094 2.188,1.094 false 2.521,0.771 2.208,0.771 false 3.417,1.302 3.198,1.302 false 4.198,1.51 4.198,1.25 false 0.885,2.719 0.573,2.719 false 0.688,4.188 0.688,3.896 false 0.958,4.688 0.958,4.406 false 1.656,4.635 1.427,4.635 1.427,4.635 1.427,4.375 false 6.427,3.969 6.042,3.969 false 1.594,2.813 1.594,3.229 1.594,3.229 1.365,3.229 false 5.583,1.344 5.229,1.344 false 2.51,0.333 1.031,0.333 false 1.896,1.135 1.167,1.135 1.167,1.135 1.167,0.333 false 1.344,5.271 1.344,4.969 false 3.75,5.458 3.75,5.26 false 4.01,5 3.677,5 false 4.125,4.75 3.792,4.75 false 3.188,1.01 3.104,1.01 3.104,1.01 3.104,1.271 false 6.792,3.781 7.115,4.146 0.323,0.365 18 false 40 1.906,0.573 2.26,0.927 0.354,0.354 18 false 41 1.76,0.677 2.115,1.031 0.354,0.354 10 false ● 5.948,1.156 6.302,1.51 0.354,0.354 18 false 43 2.01,4.438 2.365,4.792 0.354,0.354 18 false 45 1.385,5.24 1.74,5.594 0.354,0.354 18 false 46 3.802,5.406 4.156,5.708 0.354,0.302 18 false 47 0.24,2.563 0.594,2.917 0.354,0.354 18 false 44 2.021,0.99 2.25,1.198 0.229,0.208 10 false *5 3.479,1.208 3.865,1.375 0.385,0.167 10 false ★ *4 4.135,1.531 4.365,1.74 0.229,0.208 10 false *3 0.896,4.719 1.125,4.927 0.229,0.208 10 false *1 0.615,4.208 0.844,4.417 0.229,0.208 10 false *2 1.667,2.698 1.896,2.906 0.229,0.208 10 false x2 0.698,3.156 1.708,3.448 1.01,0.292 8 false 17 (173, 13) 0.708,0.167 1.063,0.521 0.354,0.354 18 false 42 3.51,4.896 3.74,5.104 0.229,0.208 10 false *6 4.167,4.635 4.396,4.844 0.229,0.208 10 false *7 3.219,0.938 4.229,1.229 1.01,0.292 8 false 28 (286, 21)

Procedure Part Name Code
Z101186

Z101188

Z101187

40 INPUT SHAFT ASSEMBLY - (Click here) - -
41 OUTER SELECT LEVER OIL SEAL 33257C (Click here) - -
42 OUTER SELECT LEVER 33257 (Click here) - -
43 SHIFT AND SELECT LEVER SHAFT ASSEMBLY - (Click here) - -
44 REVERSE SHIFT ARM BRACKET ASSEMBLY 33240 - - -
45 REVERSE SHIFT FORK 33211 (Click here) - -
46 REVERSE SHIFT FORK SHAFT ASSEMBLY - (Click here) - -
47 REVERSE IDLER GEAR SUB-ASSEMBLY 33402 (Click here) - -

*1 REVERSE SHIFT FORK SLOTTED SPRING PIN *2 NO. 4 GEAR SHIFT FORK SHAFT
*3 SHIFT INTER LOCK PLATE *4 INNER SELECT LEVER SET BOLT
*5 INNER SELECT LEVER *6 REVERSE IDLER GEAR SHAFT
*7 REVERSE IDLER THRUST WASHER - -
V100135

Gear Oil
V100136

Adhesive 1324
● Non-reusable part ★ Precoated part

C461149N01
0.031,0.604 0.833,0.813 0.802,0.208 1.49,5.292 2.313,5.479 0.823,0.188 3.073,2.552 3.844,2.719 0.771,0.167 5.26,1.385 6.052,1.552 0.792,0.167 6.292,2.573 7.01,2.76 0.719,0.188 5.219,2.479 7.135,5.167 1.917,2.688 2.885,2.479 4.313,3.24 1.427,0.76 3.135,5.323 3.875,5.5 0.74,0.177 0.427,0.271 0.427,0.604 false 0.469,2.531 0.469,2.885 false 2.563,2.854 2.875,2.854 false 3.844,2.635 3.979,2.635 false 3.708,2.885 4.031,2.885 false 3.823,2.073 4.146,2.073 false 3.198,3.448 3.365,3.448 3.365,3.448 3.5,3.635 false 4.979,2.094 4.979,1.469 4.979,1.469 5.26,1.469 false 6.01,2.479 6.01,2.052 6.01,2.052 6.292,2.052 false 5.646,2.76 5.646,3.031 false 6.073,5.031 5.906,5.031 5.906,5.031 5.813,4.865 false 5.75,3.917 5.75,4.188 false 1.906,4.938 1.906,5.292 false 2.917,4.813 3.052,5.052 3.052,5.052 3.219,5.052 false 2.677,4.875 2.969,5.406 2.969,5.406 3.135,5.406 false 5.292,5.438 5.635,5.438 false 5.885,2.677 6.125,2.677 false 6,4.802 6.073,4.802 6.073,4.802 6.073,2.688 false 5.938,3.854 6.063,3.854 false 6.531,0.24 6.854,0.24 false 2.854,3.281 3.26,3.594 0.406,0.313 18 false 49 2.219,2.677 2.625,3 0.406,0.323 18 false 54 0.583,2.854 0.99,3.167 0.406,0.313 18 false 52 0.438,2.927 0.844,3.24 0.406,0.313 10 false ● 6.427,1.365 6.646,1.552 0.219,0.188 10 false ★ 6.594,1.281 7,1.594 0.406,0.313 18 false 56 3.49,1.896 3.896,2.208 0.406,0.313 18 false 50 6.635,1.865 6.969,2.177 0.333,0.313 18 false 53 6.167,5.25 6.5,5.563 0.333,0.313 18 false 51 6.01,5.333 6.26,5.552 0.25,0.219 10 false ● 4.385,5.229 4.719,5.542 0.333,0.313 18 false 55 4.229,5.313 4.448,5.5 0.219,0.188 10 false ★ 3.281,4.938 3.531,5.115 0.25,0.177 10 false ● 0.531,0.104 0.938,0.417 0.406,0.313 10 false x2 0.073,0.625 0.917,0.917 0.844,0.292 8 false 29.4 (300, 22) 3.104,2.552 3.927,2.75 0.823,0.198 8 false 24.5 (250, 18) 3.063,2.75 3.271,2.948 0.208,0.198 10 false *1 3.531,2.781 3.74,2.979 0.208,0.198 10 false *2 2.927,2.552 3.146,2.74 0.219,0.188 10 false ★ 1.542,5.302 2.438,5.583 0.896,0.281 8 false 29.4 (300, 22) 2.073,4.875 2.344,5.052 0.271,0.177 10 false x14 6.115,4.927 6.323,5.125 0.208,0.198 10 false *4 5.688,4.208 5.896,4.406 0.208,0.198 10 false *4 5.583,3.042 5.792,3.24 0.208,0.198 10 false *4 6.302,2.771 6.51,2.969 0.208,0.198 10 false *3 6.156,2.573 6.375,2.76 0.219,0.188 10 false ★ 3.167,5.333 3.958,5.531 0.792,0.198 8 false 30 (306, 22) 6.333,2.583 7.156,2.896 0.823,0.313 8 false 22 (224, 16) 6.198,0.073 6.604,0.385 0.406,0.313 18 false 48 5.302,1.385 6.198,1.667 0.896,0.281 8 false 29.4 (300, 22)

Procedure Part Name Code
Z101186

Z101188

Z101187

48 CLEAN TRANSMISSION CASE - (Click here) - -
49 INSTALL MANUAL TRANSMISSION CASE 33111 (Click here)
50 OUTER SHIFT LEVER E-RING 33253F - - -
51 FRONT DRIVE SHAFT OIL SEAL LH 43420H (Click here) - -
52 FRONT DRIVE SHAFT OIL SEAL RH 43410M (Click here) - -
53 SHIFT DETENT BALL 33275C (Click here) - -
54 LOCK BALL PIN 33292A (Click here) - -
55 REVERSE IDLER GEAR SHAFT BOLT 33451H (Click here) - -
56 NO. 1 LOCK BALL ASSEMBLY 33290 (Click here) - -

*1 SHIFT AND SELECT LEVER SHAFT WITH HEAD STRAIGHT SCREW PLUG *2 SHIFT AND SELECT LEVER SHAFT COMPRESSION SPRING
*3 SHIFT DETENT BALL PLUG *4 SHIFT DETENT BALL COMPRESSION SPRING
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Adhesive 1344
V100136

Adhesive 1324
★ Precoated part - -

C465069N01
0.823,0.969 1.646,1.167 0.823,0.198 2.177,0.313 3.198,0.5 1.021,0.188 4.552,0.688 5.25,0.875 0.698,0.188 6.208,3.406 7,3.615 0.792,0.208 0.99,3.365 1.792,3.542 0.802,0.177 1.521,2.396 2.354,2.719 0.833,0.323 1.49,2.354 2.396,2.76 0.906,0.406 0.573,4.469 1.573,4.667 1,0.198 4.448,5.125 5.271,5.333 0.823,0.208 5.958,5.375 6.698,5.583 0.74,0.208 6.063,1.354 6.813,1.521 0.75,0.167 4.521,0.385 5.323,0.594 0.802,0.208 2.021,1.063 1.646,1.063 false 1.813,2.938 1.438,2.938 false 2.125,3.458 1.792,3.458 false 2.115,3.688 1.823,3.688 false 4.927,4.719 4.635,4.719 false 5.74,4.198 5.552,4.198 5.552,4.198 5.552,4.771 false 4.854,5.115 4.854,4.854 4.854,4.854 5.094,4.854 false 5.031,1.333 4.729,1.333 false 6.865,0.229 6.615,0.229 false 6.198,2.615 6.031,2.615 6.031,2.615 5.938,2.969 false 6.323,2.885 6.604,2.885 6.604,2.885 6.604,3.406 false 2.458,1.688 2.313,1.688 false 3.573,1.281 3.302,0.792 3.302,0.792 3.135,0.792 false 3.615,0.542 3.729,0.354 3.729,0.354 3.896,0.354 false 3.594,0.688 3.365,0.406 3.365,0.406 3.198,0.406 false 4.552,0.781 4.25,0.781 false 3.531,2.177 3.156,2.177 true 1.948,4.573 1.573,4.573 false 2.375,4.802 1.917,5.115 1.917,5.115 1.635,5.115 false 2.875,4.677 2.688,4.677 2.688,4.677 2.688,4.854 false 5.802,4.938 6.323,4.938 6.323,4.938 6.323,5.375 false 1.948,1.844 1.948,2.385 false 1.677,1.885 1.677,2.219 1.677,2.219 1.948,2.219 false 1.625,1.792 1.344,2.333 1.344,2.333 1.167,2.333 false 6.208,2.01 5.906,2.01 false 6.063,1.438 5.76,1.438 false 4.521,0.49 4.354,0.49 4.354,0.49 3.75,0.906 false 1.844,0.26 2.198,0.573 0.354,0.313 18 false 58 2.229,0.323 3.396,0.594 1.167,0.271 8 false 8.4 (86, 74 in.*lbf) 1.979,0.604 3.104,0.917 1.125,0.313 18 false 63, 66, 68 3.958,0.188 4.417,0.5 0.458,0.313 18 false 59 5.865,0.052 7.042,0.573 1.177,0.521 18 false 65, 67 0.427,2.177 1.323,2.521 0.896,0.344 18 false 62, 64 0.646,3.271 1.104,3.583 0.458,0.313 18 false 72 1.125,2.76 1.583,3.073 0.458,0.313 18 false 57 2.917,1.521 4.125,2.094 1.208,0.573 18 false 60 2.76,1.573 2.948,1.76 0.188,0.188 10 false ● 5.104,1.167 5.563,1.479 0.458,0.313 18 false 70 1.688,3.594 1.979,3.781 0.292,0.188 10 false ● 6.25,3.427 7.063,3.635 0.813,0.208 8 false 40.2 (410, 30) 5.844,3.323 6.302,3.635 0.458,0.313 18 false 71 6.26,2.51 6.458,2.688 0.198,0.177 10 false ● 0.542,0.979 0.906,1.177 0.365,0.198 10 false ● ★ 0.885,0.979 1.75,1.24 0.865,0.26 8 false 22.5 (229, 17) 2.177,0.958 2.406,1.125 0.229,0.167 10 false x3 3.802,0.906 4.031,1.073 0.229,0.167 10 false x2 4.583,0.688 5.469,0.958 0.885,0.271 8 false 17 (173, 13) 4.115,5.073 4.573,5.385 0.458,0.313 18 false 74 5.625,5.313 6.083,5.625 0.458,0.313 18 false 75 4.479,4.615 4.771,4.802 0.292,0.188 10 false ● 5.813,4.104 6.104,4.292 0.292,0.188 10 false ● 1.552,2.406 2.563,2.594 1.01,0.188 8 false 15.2 (155, 11) 1.552,2.531 2.917,2.823 1.365,0.292 8 false 13.4 (137, 10)* 2.833,2.01 3.292,2.323 0.458,0.313 18 false 61 1.281,4.938 1.74,5.25 0.458,0.313 18 false 73 0.625,4.479 1.604,4.646 0.979,0.167 8 false 7.8 (80, 69 in.*lbf) 1.031,3.375 2.021,3.646 0.99,0.271 8 false 40.2 (410, 30) 6.01,5.396 6.823,5.604 0.813,0.208 8 false 45 (459, 33) 4.51,5.146 5.323,5.354 0.813,0.208 8 false 39.2 (400, 29) 4.26,0.792 4.49,0.958 0.229,0.167 10 false x3 0.406,4.458 0.698,4.646 0.292,0.188 10 false ★ 2.938,4.573 3.229,4.76 0.292,0.188 10 false ● 6.26,1.844 6.719,2.156 0.458,0.313 18 false 69 6.104,1.354 6.99,1.625 0.885,0.271 8 false 20 (204, 15) 4.563,0.406 6.281,0.563 1.719,0.156 8 false 16.7 (170, 12)

Procedure Part Name Code
Z101186

Z101188

Z101187

57 NO. 1 CLUTCH HOUSING COVER 31121 - - -
58 RELEASE CYLINDER BLEEDER PLUG - - - -
59 RELEASE CYLINDER BLEEDER PLUG CAP 31478 - - -
60 CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY 31400 (Click here) - -
61 CLUTCH TUBE BOOT 31126B - - -
62 TEMPORARILY INSTALL BLEEDER CLUTCH RELEASE TUBE 31483 (Click here) - -
63 TEMPORARILY INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY 31407B (Click here) - -
64 FULLY TIGHTEN BLEEDER CLUTCH RELEASE TUBE 31483 (Click here) - -
65 APPLY GREASE - (Click here) - -
66 REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY 31407B (Click here) - -
67 INSPECT CLUTCH PIPE LINE - (Click here) - -
68 INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY 31407B (Click here) - -
69 WIRE HARNESS CLAMP BRACKET - - - -
70 CONTROL CABLE BRACKET ASSEMBLY 335A0 - - -
71 NEUTRAL POSITION SWITCH 84545 (Click here) - -
72 BACK-UP LIGHT SWITCH ASSEMBLY 84210 (Click here) - -
73 TRANSMISSION REVOLUTION SENSOR 89413B (Click here) - -
74 MANUAL TRANSMISSION FILLER PLUG 33101A (Click here) - -
75 MANUAL TRANSMISSION DRAIN PLUG 33101B (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

Gear Oil
V100136

Adhesive 1324
● Non-reusable part ★ Precoated part

PROCEDURE

Hide 41311E 1.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C461151N01
0.958,2.573 0.771,2.573 0.771,2.573 0.771,2.115 false 2.073,1.167 1.969,1.167 1.969,1.167 1.969,0.823 false 0.99,2.115 0.552,2.115 false 2.125,0.823 1.885,0.823 false 4.573,1.719 4.073,1.719 true 4.479,2.688 4.375,2.688 4.375,2.688 4.375,1.729 true 5.781,0.688 5.49,0.688 false 5.667,0.698 5.667,0.958 true 0.25,2.01 0.667,2.208 0.417,0.198 10 false SST 1.583,0.719 1.969,0.938 0.385,0.219 10 false SST 5.177,0.583 5.573,0.792 0.396,0.208 10 false SST 3.76,1.615 4.115,1.792 0.354,0.177 10 false SST 0.469,0.24 0.729,0.604 0.26,0.365 18 false i 4.083,0.229 4.344,0.594 0.26,0.365 18 false ii

i.

Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the front differential case with ring gear assembly.

SST
09309-37010  
09506-35010  


ii.

Using SST and a press, install a new front differential case front tapered roller bearing (outer race) together with the front differential case front plate washer to the front transaxle (MTM) case.

SST
09950-60021  (09951-00680)
09950-70010  (09951-07200)



Hide 41311F 2.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C461152N01
1.948,0.729 1.823,0.729 1.823,0.729 1.823,0.406 false 1.177,2.667 0.958,2.667 0.958,2.667 0.958,2.417 true 5.323,2.542 6.073,2.542 true 0.823,2.417 1.25,2.417 false 1.646,0.406 2.021,0.406 false 4.979,2.073 4.76,2.073 4.76,2.073 4.76,1.542 true 4.625,1.531 5.115,1.531 false 5.75,0.563 5.99,0.563 false 5.875,0.573 5.875,0.844 false 6.469,1.396 6.583,1.396 false 0.458,0.219 0.625,0.552 0.167,0.333 18 false i 4.094,0.229 4.26,0.563 0.167,0.333 18 false ii 1.344,0.302 1.781,0.521 0.438,0.219 10 false SST 0.521,2.313 0.906,2.49 0.385,0.177 10 false SST 5.438,0.458 5.802,0.635 0.365,0.177 10 false SST 6.646,1.292 7.052,1.563 0.406,0.271 10 false SST 4.302,1.427 4.688,1.646 0.385,0.219 10 false SST 6.135,2.438 6.646,2.729 0.51,0.292 10 false SST

i.

Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the front differential case with ring gear assembly.

SST
09636-20010  
09726-40010  


ii.

Using SST and a press, install a new front differential case rear tapered roller bearing (outer race) together with the front differential case rear shim to the manual transmission case.

SST
09309-36010  
09950-60021  (09951-00730)
09950-70010  (09951-07100)

HINT:

Use a front differential case rear shim of the same thickness as the removed one.




Hide 3.CLEAN TRANSMISSION CASE

a.
C461153C01
0.427,0.052 0.708,0.406 0.281,0.354 18 false i
V100145

Area to be cleaned - -


i.

Clean and degrease the contact surfaces of the front transaxle (MTM) case and manual transmission case.



Hide 41300 4.INSTALL FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY

a.
C461154C01
0.438,0.031 0.719,0.385 0.281,0.354 18 false i 3.885,0.021 4.167,0.375 0.281,0.354 18 false ii
V100135

Gear Oil - -


i.

Coat the front differential case with ring gear assembly with gear oil.


ii.

Install the front differential case with ring gear assembly to the front transaxle (MTM) case.



Hide 33111 5.INSTALL MANUAL TRANSMISSION CASE

a.
C433189

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 6.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.
C461155C01
2.115,0.969 2.333,0.969 2.333,0.969 2.656,1.292 true 1.969,1.802 1.969,1.625 1.969,1.625 2.781,1.625 true 0.417,0.021 1.688,0.438 1.271,0.417 18 false i, ii, iii, iv, v 1.917,0.875 2.115,1.052 0.198,0.177 10 false *1 1.833,1.823 2.354,2 0.521,0.177 10 false SST
*1 Front Differential Case Rear Shim - -


i.

Using SST and a torque wrench, turn the front differential case with ring gear assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-32011  


ii.

Using SST and a torque wrench, measure the differential side bearing preload.

SST
09564-32011  

Differential Side Bearing Preload (at Starting):
Bearing Differential Side Bearing Preload (at Starting)
New Bearing 0.980 to 1.69 N*m (10 to 17 kgf*cm, 9 to 14 in.*lbf)
Used Bearing 0.795 to 1.37 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)



iii.

If the differential side bearing preload is not as specified, replace the front differential case rear shim with one of a different thickness. Use the table below to select a front differential case rear shim which will ensure that the differential side bearing preload is within the specification.

Front Differential Case Rear Shim Thickness:
Mark Thickness Mark Thickness
10 2.100 mm (0.0827 in.) 26 2.500 mm (0.0984 in.)
11 2.125 mm (0.0837 in.) 27 2.525 mm (0.0994 in.)
12 2.150 mm (0.0846 in.) 28 2.550 mm (0.1004 in.)
13 2.175 mm (0.0856 in.) 29 2.575 mm (0.1014 in.)
14 2.200 mm (0.0866 in.) 30 2.600 mm (0.1024 in.)
15 2.225 mm (0.0876 in.) 31 2.625 mm (0.1033 in.)
16 2.250 mm (0.0886 in.) 32 2.650 mm (0.1043 in.)
17 2.275 mm (0.0896 in.) 33 2.675 mm (0.1053 in.)
18 2.300 mm (0.0906 in.) 34 2.700 mm (0.1063 in.)
19 2.325 mm (0.0915 in.) 35 2.725 mm (0.1073 in.)
20 2.350 mm (0.0925 in.) 36 2.750 mm (0.1083 in.)
21 2.375 mm (0.0935 in.) 37 2.775 mm (0.1093 in.)
22 2.400 mm (0.0945 in.) 38 2.800 mm (0.1102 in.)
23 2.425 mm (0.0955 in.) 39 2.825 mm (0.1112 in.)
24 2.450 mm (0.0965 in.) 40 2.850 mm (0.1122 in.)
25 2.475 mm (0.0974 in.) - -



iv.

Select a thicker front differential case rear shim to increase the differential side bearing preload or a thinner front differential case rear shim to decrease the differential side bearing preload.


v.

Make a memo as the torque values will be needed to adjust output shaft bearing preload.



Hide 33111 7.REMOVE MANUAL TRANSMISSION CASE

Hide 41300 8.REMOVE FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY

Hide 33321N 9.INSTALL FRONT OUTPUT SHAFT BEARING (OUTER RACE)

a.
C461156C01
1.323,1.073 1.615,1.073 true 4.76,1.094 4.76,1.469 4.76,1.469 5.01,1.469 true 4.583,1.083 5.115,1.083 false 5.958,0.26 6.229,0.26 false 6.104,0.26 6.104,0.542 false 1.156,0.958 1.333,1.135 0.177,0.177 10 true *a 5.656,0.156 5.958,0.344 0.302,0.188 10 false SST 4.271,0.979 4.719,1.167 0.448,0.188 10 false SST 0.417,0.021 0.698,0.375 0.281,0.354 18 false i 4.094,0.031 4.375,0.385 0.281,0.354 18 false ii
*a Key - -


i.

Install the output shaft cover to the front transaxle (MTM) case.

NOTICE:

Insert the key of the output shaft cover into the front transaxle (MTM) case groove.



ii.

Using SST and a press, install a new front output shaft bearing (outer race) to the front transaxle (MTM) case.

SST
09950-60011  (09951-00630)
09950-70010  (09951-07150)



Hide 33321A 10.INSTALL REAR OUTPUT SHAFT BEARING (OUTER RACE)

a.
C461157N01
4.375,1.938 4.375,2.156 4.375,2.156 4.594,2.156 false 4.25,1.938 4.781,1.938 false 1.76,1.083 2.896,1.083 true 1.948,1.094 1.948,1.313 1.948,1.313 2.823,1.313 true 0.427,0.031 0.563,0.344 0.135,0.313 18 false i 1.469,0.969 1.771,1.167 0.302,0.198 10 false SST 3.948,1.833 4.25,2.031 0.302,0.198 10 false SST

i.

Using SST and a press, install a new rear output shaft bearing (outer race) together with the rear output shaft bearing shim to the manual transmission case.

SST
09950-60011  (09951-00590)
09950-70010  (09951-07200)

HINT:

Use a rear output shaft bearing shim of the same thickness as the removed one.




Hide 11.CLEAN TRANSMISSION CASE

a.
C461153C01
0.427,0.052 0.708,0.406 0.281,0.354 18 false i
V100145

Area to be cleaned - -


i.

Clean and degrease the contact surfaces of the front transaxle (MTM) case and manual transmission case.



Hide 41300 12.INSTALL FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY

Hide 13.INSTALL OUTPUT SHAFT ASSEMBLY

a.
C461158C01
2.115,0.188 2.396,0.542 0.281,0.354 18 false i 0.417,0.031 0.698,0.385 0.281,0.354 18 false i 3.438,0.031 3.719,0.385 0.281,0.354 18 false ii
V100135

Gear Oil - -


i.

Coat the output shaft assembly with gear oil.


ii.

Install the output shaft assembly to the front transaxle (MTM) case.



Hide 33111 14.INSTALL MANUAL TRANSMISSION CASE

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

Hide 15.ADJUST OUTPUT SHAFT BEARING PRELOAD

a.
C461159C01
2.625,0.5 2.979,0.5 true 1.75,1.875 2.438,1.875 true 1.448,1.771 1.74,1.917 0.292,0.146 10 false SST 2.448,0.396 2.667,0.552 0.219,0.156 10 false *1 0.406,0.031 1.177,0.354 0.771,0.323 18 false i, ii, iii
*1 Rear Output Shaft Bearing Shim - -


i.

Using SST and a torque wrench, turn the front differential case with ring gear assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-32011  


ii.

Using SST and a torque wrench, measure the preload. Calculate the rear output shaft bearing preload using the following formula.

SST
09564-32011  

Formula:

Measured Preload - Differential Side Bearing Preload = Output Shaft Bearing Preload

Bearing Output Shaft Bearing Preload (at starting)
New bearing 4.54 to 7.99 N*m (47 to 81 kgf*cm, 41 to 70 in.*lbf)
Used bearing 2.92 to 5.15 N*m (30 to 52 kgf*cm, 26 to 45 in.*lbf)



iii.

If the output shaft bearing preload is not as specified, replace the rear output shaft bearing shim with one of a different thickness. Use the table below to select a rear output shaft bearing shim which will ensure that the output shaft bearing preload is within the specification.

Rear Output Shaft Bearing Shim Thickness:
Mark Thickness Mark Thickness
50 1.750 mm (0.0689 in.) 72 2.300 mm (0.0906 in.)
51 1.775 mm (0.0699 in.) 73 2.325 mm (0.0915 in.)
52 1.800 mm (0.0709 in.) 74 2.350 mm (0.0925 in.)
53 1.825 mm (0.0719 in.) 75 2.375 mm (0.0935 in.)
54 1.850 mm (0.0728 in.) 76 2.400 mm (0.0945 in.)
55 1.875 mm (0.0738 in.) 77 2.425 mm (0.0955 in.)
56 1.900 mm (0.0748 in.) 78 2.450 mm (0.0965 in.)
57 1.925 mm (0.0758 in.) 79 2.475 mm (0.0974 in.)
58 1.950 mm (0.0768 in.) 80 2.500 mm (0.0984 in.)
59 1.975 mm (0.0778 in.) 81 2.525 mm (0.0994 in.)
60 2.000 mm (0.0787 in.) 82 2.550 mm (0.1004 in.)
61 2.025 mm (0.0797 in.) 83 2.575 mm (0.1014 in.)
62 2.050 mm (0.0807 in.) 84 2.600 mm (0.1024 in.)
63 2.075 mm (0.0817 in.) 85 2.625 mm (0.1033 in.)
64 2.100 mm (0.0827 in.) 86 2.650 mm (0.1043 in.)
65 2.125 mm (0.0837 in.) 87 2.675 mm (0.1053 in.)
66 2.150 mm (0.0846 in.) 88 2.700 mm (0.1063 in.)
67 2.175 mm (0.0856 in.) 89 2.725 mm (0.1073 in.)
68 2.200 mm (0.0866 in.) 90 2.750 mm (0.1083 in.)
69 2.225 mm (0.0876 in.) 91 2.775 mm (0.1093 in.)
70 2.250 mm (0.0886 in.) 92 2.800 mm (0.1102 in.)
71 2.275 mm (0.0896 in.) - -


HINT:

Select a thicker rear output shaft bearing shim to increase the output shaft bearing preload or a thinner rear output shaft bearing shim to decrease the output shaft bearing preload.




Hide 33111 16.REMOVE MANUAL TRANSMISSION CASE

Hide 17.REMOVE OUTPUT SHAFT ASSEMBLY

Hide 41300 18.REMOVE FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY

Hide 33253H 19.INSTALL OUTER SHIFT LEVER OIL SEAL

a.
C462176N01
3.969,1.573 5.073,1.573 true 3.823,1.438 4.854,1.438 4.854,1.438 4.854,1.563 true 0.417,0.021 0.99,0.302 0.573,0.281 18 false i 5.125,1.469 5.427,1.646 0.302,0.177 10 false SST 2.74,1.208 3.198,1.406 0.458,0.198 10 false (A)

i.

Using SST and a hammer, install a new outer shift lever oil seal to the manual transmission case.

SST
09950-60011  (09951-00260)
09950-70010  (09951-07100)

Standard Depth (A):

0.5 to 1.0 mm (0.0197 to 0.0394 in.)




Hide 33253 20.INSTALL OUTER NO. 1 SHIFT LEVER

a.
C462167N01
0.427,0.042 0.906,0.354 0.479,0.313 18 false i, ii 2.573,2 2.885,2.198 0.313,0.198 10 false (A)

i.

Install the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever to the manual transmission case.


ii.

Using a 5 mm pin punch and hammer, install the inner shift lever slotted spring pin to the inner No. 1 shift lever.

Standard Depth (A):

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)




Hide 33109C 21.INSTALL MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY

a.
C461161N01
0.406,0.021 1.26,0.458 0.854,0.438 18 false i, ii

i.

Install the manual transmission oil separator sub-assembly to the manual transmission case with the 3 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


ii.

Make sure that the end tabs of the manual transmission oil separator sub-assembly are inserted into the grooves of the manual transmission case.



Hide 33111J 22.INSTALL MANUAL TRANSMISSION CASE STRAIGHT PIN

a.
C461162N01
4.667,0.604 4.917,0.813 0.25,0.208 10 false (A) 0.427,0.031 0.563,0.344 0.135,0.313 18 false i

i.

Using a plastic hammer, install 5 new manual transmission case straight pins to the front transaxle (MTM) case to the specified protrusion height (A).

Protrusion Height (A):

8.5 to 9.5 mm (0.335 to 0.374 in.)




Hide 33280 23.INSTALL REVERSE RESTRICT PIN ASSEMBLY

Hide 33101J 24.INSTALL BREATHER PLUG

a.
C461163N01
2.771,2.531 2.938,2.531 2.938,2.531 3.323,1.813 true 4.135,0.719 4.135,0.823 false 0.427,0.042 0.563,0.354 0.135,0.313 18 false i 2.469,2.438 2.771,2.646 0.302,0.208 10 false SST 4.01,0.833 4.313,1.042 0.302,0.208 10 false SST

i.

Using SST and a hammer, install the breather plug to the front transaxle (MTM) case.

SST
09350-30020  (09350-07110)



Hide 33176B 25.INSTALL TRANSMISSION OIL SEPARATOR

a.
C461164N01
0.427,0.031 1.083,0.604 0.656,0.573 18 false i, ii

i.

Install the transmission oil separator to the manual transmission case with the 2 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


ii.

Make sure that the tip of the transmission oil separator is inserted into the groove of the manual transmission case.



Hide 33124C 26.INSTALL NO. 1 OIL RECEIVER PIPE

a.
C461165N01
0.427,0.031 0.979,0.521 0.552,0.49 18 false i, ii

i.

Install the No. 1 oil receiver pipe to the manual transmission case.


ii.

Make sure that the No. 1 oil receiver pipe fully contacts the manual transmission case.



Hide 33176D 27.INSTALL NO. 2 TRANSMISSION OIL SEPARATOR

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)

Hide 31105D 28.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C462177N01
4.177,1.094 4.104,1.094 4.104,1.094 4.104,0.875 false 4.031,0.875 4.24,0.875 false 2.656,2.51 2.656,1.969 2.656,1.969 3.313,1.969 true 2.667,2.052 3.292,2.052 true 3.729,0.771 4.031,0.948 0.302,0.177 10 false SST 5.021,1.063 5.271,1.26 0.25,0.198 10 true (A) 2.521,2.521 2.823,2.698 0.302,0.177 10 false SST 0.427,0.031 0.896,0.396 0.469,0.365 18 false i

i.

Using SST and a hammer, install a new front transaxle case oil seal to the front transaxle (MTM) case.

SST
09950-60011  (09951-00350)
09950-70010  (09951-07100)

Standard Depth (A):

0.9 to 1.9 mm (0.0354 to 0.0748 in.)




Hide 33449B 29.INSTALL TRANSMISSION MAGNET

a.
C461167N01
0.427,0.021 0.865,0.333 0.438,0.313 18 false i, ii

i.

Clean the transmission magnet.


ii.

Install transmission magnet to the front transaxle (MTM) case.



Hide 41300 30.INSTALL FRONT DIFFERENTIAL CASE WITH RING GEAR ASSEMBLY

Hide 33137 31.INSTALL INPUT SHAFT COVER

Z101186

NOTICE:

Insert the key of the input shaft cover into the manual transmission case groove.



a.
C433103C02
2.656,1.521 2.813,1.521 2.813,1.521 3.281,1.667 true 2.469,1.427 2.646,1.615 0.177,0.188 10 true *a
*a Key - -



Hide 33311K 32.INSTALL REAR INPUT SHAFT BEARING SHIM

a.
C461168C01
0.771,2.698 1.104,2.698 false 3.5,3.469 3.833,3.469 false 4.625,2.802 4.625,3.302 false 1.448,0.031 2.604,0.375 1.156,0.344 18 false i, v, vi, vii 4.76,1.896 5.01,2.198 0.25,0.302 18 false iii 0.604,2.594 0.802,2.781 0.198,0.188 10 false *1 2.448,2.854 2.781,3.083 0.333,0.229 10 false (A) 4.229,2.563 4.563,2.854 0.333,0.292 10 false (C) 6.823,2.604 7.146,2.844 0.323,0.24 10 false (B) 3.875,3.365 4.073,3.552 0.198,0.188 10 false *2 4.563,3.313 4.76,3.5 0.198,0.188 10 false *3 0.417,1.896 0.667,2.198 0.25,0.302 18 false ii 2.844,1.885 3.094,2.188 0.25,0.302 18 false iv
*1 Manual Transmission Case *2 Input Shaft Assembly
*3 Front Transaxle (MTM) Case - -
V100135

MP Grease - -


i.

Install the rear input shaft bearing shim to the manual transmission case.

NOTICE:

The rear input shaft bearing shim should be cleaned before assembly.



ii.

Measure the distance between the end of the manual transmission case and rear input shaft bearing shim (Dimension (A)).


iii.

Measure the distance between the end of the front transaxle (MTM) case and installation surface of the front input shaft bearing (Dimension (B)).


iv.

Measure the distance between both input shaft bearing outer races (Dimension (C)).

NOTICE:

Measure Dimension (C) with each bearing having no axial clearance.



v.

Calculate the rear input shaft bearing shim value using the following formula.

Formula:

(Dimension (A) + Dimension (B)) - Dimension (C) - Input Shaft Bearing Clearance = 0.02 to 0.14 mm (0.000787 to 0.005512 in.)



vi.

If the input shaft bearing clearance is not as specified, replace the rear input shaft bearing shim with one of a different thickness. Use the table below to select a rear input shaft bearing shim which will ensure that the input shaft bearing clearance is within the specification.

Rear Input Shaft Bearing Shim Thickness:
Mark Thickness Mark Thickness
08 1.30 mm (0.0512 in.) 14 1.60 mm (0.0630 in.)
09 1.35 mm (0.0531 in.) 15 1.65 mm (0.0650 in.)
10 1.40 mm (0.0551 in.) 16 1.70 mm (0.0669 in.)
11 1.45 mm (0.0571 in.) 17 1.75 mm (0.0689 in.)
12 1.50 mm (0.0591 in.) 18 1.80 mm (0.0709 in.)
13 1.55 mm (0.0610 in.) 19 1.85 mm (0.0728 in.)



vii.

Coat the rear input shaft bearing shim with MP grease and install it to the manual transmission case.

NOTICE:

Do not apply MP grease to the oil grooves.




Hide 33239 33.INSTALL NO. 3 REVERSE PRE-BALK HEAD

a.
C461169N01
0.719,0.146 1,0.5 0.281,0.354 18 false i 4.135,0.146 4.417,0.5 0.281,0.354 18 false ii 0.708,2.521 0.99,2.875 0.281,0.354 18 false iii 2.396,2.813 2.854,3.01 0.458,0.198 10 false (A)

i.

Secure the No. 3 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



ii.

Install the No. 3 reverse pre-balk head to the No. 3 gear shift fork assembly.

NOTICE:

Confirm the installation direction.



iii.

Using a 5 mm pin punch and a hammer, install the slotted spring pin to the No. 3 reverse pre-balk head.

Standard Depth (A):

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)




Hide 33234A 34.INSTALL NO. 3 GEAR SHIFT HEAD

a.
C461170N01
0.406,0.021 0.646,0.302 0.24,0.281 18 false i 3.948,0.021 4.229,0.375 0.281,0.354 18 false ii 5.823,0.469 6.073,0.698 0.25,0.229 10 false (A) 6.052,0.635 6.302,0.865 0.25,0.229 10 false (A)

i.

Install the No. 3 gear shift head to the No. 3 gear shift fork assembly.

NOTICE:

Confirm the installation direction.



ii.

Using a 5 mm pin punch and a hammer, install the slotted spring pin to the No. 3 gear shift head.

Standard Height (A):

1.0 mm (0.0394 in.) or less




Hide 33291A 35.INSTALL SHIFT FORK SHAFT STOPPER

a.
C461171N01
0.719,0.156 1,0.51 0.281,0.354 18 false i 3.708,0.156 3.99,0.51 0.281,0.354 18 false ii 0.698,2.531 0.979,2.885 0.281,0.354 18 false iii 4.604,3.042 4.885,3.396 0.281,0.354 18 false iv 2.156,3.021 2.615,3.219 0.458,0.198 10 false (A)

i.

Secure the No. 2 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



ii.

Install the shift fork shaft stopper to the No. 2 gear shift fork assembly as shown in the illustration.

NOTICE:

Confirm the installation direction.



iii.

Using a 5 mm pin punch and a hammer, install the slotted spring pin to the shift fork shaft stopper.

Standard Depth (A):

-0.1 to 0.9 mm (-0.00394 to 0.0354 in.)



iv.

Install the No. 2 reverse pre-balk head torsion spring to the No. 2 gear shift fork assembly.



Hide 36.INSTALL NO. 2 REVERSE PRE-BALK HEAD BIMETAL FORMED BUSH

a.
C461172C01
5.792,1.99 5.875,1.99 5.875,1.99 6.021,1.771 true 2.417,1.979 2.5,1.979 2.5,1.979 2.635,1.771 true 1.531,2.385 1.531,1.896 1.531,1.896 1.656,1.896 false 1.531,1.969 1.667,1.969 false 4.781,2.375 4.781,1.885 4.781,1.885 4.906,1.885 false 4.781,1.979 4.917,1.979 false 0.427,0.031 0.708,0.385 0.281,0.354 18 false i 3.146,1.583 3.604,1.781 0.458,0.198 10 false (A) 5.49,1.583 5.948,1.781 0.458,0.198 10 false (A) 2.25,1.885 2.563,2.083 0.313,0.198 10 false *1 5.625,1.896 5.938,2.094 0.313,0.198 10 false *1 1.406,2.396 1.865,2.594 0.458,0.198 10 false SST 4.646,2.396 5.104,2.594 0.458,0.198 10 false SST
*1 No. 2 Reverse Pre-balk Head Bimetal Formed Bushing - -


i.

Using SST and a hammer, install 2 new No. 2 reverse pre-balk head bimetal formed Bushings to the No. 2 reverse pre-balk head.

SST
09950-60011  (09951-00210)
09950-70010  (09951-07100)

Standard Depth (A):

0 to 1.0 mm (0 to 0.0394 in.)




Hide 33238A 37.INSTALL NO. 2 REVERSE PRE-BALK HEAD

a.
C461173C01
1.354,2.323 1.74,2.323 false 0.51,2.854 0.854,2.854 true 1.177,2.823 1.75,2.823 true 0.5,3.24 0.969,3.24 true 2.208,0.021 2.615,0.333 0.406,0.313 18 false ii 5.313,0.063 5.719,0.375 0.406,0.313 18 false iii 0.406,2.021 0.813,2.333 0.406,0.313 18 false iv 0.906,4.063 1.313,4.375 0.406,0.313 18 false v 4.385,1.146 4.698,1.344 0.313,0.198 10 false (A) 1.781,2.208 2,2.427 0.219,0.219 10 false *1 0.323,3.135 0.542,3.354 0.219,0.219 10 false *4 1.792,2.719 2.01,2.938 0.219,0.219 10 false *3 0.333,2.75 0.552,2.969 0.219,0.219 10 false *2 0.427,0.042 0.833,0.354 0.406,0.313 18 false i 3.906,4.031 4.313,4.344 0.406,0.313 18 false vi
*1 No. 2 Reverse Pre-balk Head *2 No. 2 Reverse Pre-balk Head Torsion Spring
*3 No. 2 Reverse Pre-balk Head Straight Pin *4 Shift Fork Shaft Stopper
V113147

Install in this Direction (1)
V113148

Turn
V113149

Install in this Direction (2) - -


i.

Secure the No. 2 reverse pre-balk head in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



ii.

Using a 3 mm pin punch and a hammer, install the No. 2 reverse pre-balk head straight pin to the No. 2 reverse pre-balk head.

Standard Height (A):

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



iii.

Secure the No. 2 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



iv.

Install the No. 2 reverse pre-balk head to the No. 2 gear shift fork assembly as shown in the illustration.


v.

Install the No. 2 reverse pre-balk head spacer to the No. 2 gear shift fork assembly.


vi.

Using a screwdriver with its tip wrapped with protective tape and a hammer, install the shift fork shaft snap ring to the No. 2 gear shift fork assembly.

HINT:

Use a piece of cloth to keep the shift fork shaft snap ring from flying off.




Hide 33233A 38.INSTALL NO. 2 GEAR SHIFT HEAD

a.
C461174N01
6.406,0.406 6.688,0.698 0.281,0.292 10 false (A) 0.427,0.021 0.573,0.323 0.146,0.302 18 false i 3.865,0.021 4.083,0.323 0.219,0.302 18 false ii 6.604,0.625 6.885,0.917 0.281,0.292 10 false (A)

i.

Install the No. 2 gear shift head to the No. 2 gear shift fork assembly.

NOTICE:

Confirm the installation direction.



ii.

Using a 5 mm pin punch and a hammer, install the slotted spring pin to the No. 2 gear shift head.

Standard Height (A):

1.0 mm (0.0394 in.) or less




Hide 33232F 39.INSTALL NO. 1 GEAR SHIFT HEAD

a.
C461175N01
0.563,0.125 0.885,0.542 0.323,0.417 21 false i 3.823,0.135 4.146,0.552 0.323,0.417 21 false ii 0.552,2.625 0.875,3.042 0.323,0.417 21 false iii 2.698,3.99 3.156,4.188 0.458,0.198 10 false (A) 2.792,4.24 3.25,4.438 0.458,0.198 10 false (A)

i.

Secure the No. 1 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



ii.

Install the No. 1 gear shift head to the No. 1 gear shift fork assembly.

NOTICE:

Confirm the installation direction.



iii.

Using a 5 mm pin punch and a hammer, install the slotted spring pin to the No. 1 gear shift head.

Standard Height (A):

1.0 mm (0.0394 in.) or less




Hide 40.INSTALL INPUT SHAFT ASSEMBLY

a.
C461176C01
6.229,1.177 6.469,1.177 false 6.01,2.344 6.25,2.344 false 2.146,3.51 2.385,3.51 false 2.073,4.417 2.313,4.417 false 2.115,5.49 2.354,5.49 false 0.427,0.021 0.708,0.375 0.281,0.354 18 false i 4.406,0.031 4.688,0.385 0.281,0.354 18 false ii 0.146,2.823 0.427,3.177 0.281,0.354 18 false iii 2.969,2.979 3.656,3.469 0.688,0.49 18 false iv, v 6.521,1.073 6.833,1.271 0.313,0.198 10 false *1 6.292,2.24 6.604,2.438 0.313,0.198 10 false *2 2.427,3.406 2.74,3.604 0.313,0.198 10 false *3 2.354,4.323 2.667,4.521 0.313,0.198 10 false *4 2.396,5.385 2.708,5.583 0.313,0.198 10 false *5
*1 No. 1 Gear Shift Fork Assembly *2 Output Shaft Assembly
*3 No. 2 Gear Shift Fork Assembly *4 No. 3 Gear Shift Fork Assembly
*5 Input Shaft Assembly - -
V100135

Gear Oil - -


i.

Apply gear oil to all sliding and rotating parts.


ii.

Install the No. 1 gear shift fork assembly to the output shaft assembly.


iii.

Install the No. 2 gear shift fork assembly and No. 3 gear shift fork assembly to the input shaft assembly.


iv.

Temporarily install the output shaft assembly, input shaft assembly, No. 1 gear shift fork assembly, No. 2 gear shift fork assembly and No. 3 gear shift fork assembly, and tie them with a rope or string.


v.

Install the input shaft assembly, output shaft assembly, No. 1 gear shift fork assembly, No. 2 gear shift fork assembly and No. 3 gear shift fork assembly to the front transaxle (MTM) case.



Hide 33257C 41.INSTALL OUTER SELECT LEVER OIL SEAL

a.
C462178N01
2.573,0.927 2.719,0.927 2.719,0.927 3.146,1.083 true 4,1.969 4,1.854 4,1.854 3.646,1.854 false 3.813,2.063 3.813,1.865 false 4.927,0.698 3.688,0.698 true 0.417,0.031 0.958,0.333 0.542,0.302 18 false i 2.271,0.833 2.615,1.01 0.344,0.177 10 false SST 3.333,1.75 3.677,1.927 0.344,0.177 10 false SST 3.99,1.49 4.219,1.771 0.229,0.281 10 false (A) 4.99,0.594 5.333,0.771 0.344,0.177 10 false SST

i.

Using SST and a hammer, install a new outer select lever oil seal to the front transaxle (MTM) case as shown in the illustration.

SST
09950-60011  (09951-00240)
09950-70010  (09951-07100)

Standard Depth (A):

0.5 to 1.0 mm (0.0197 to 0.0394 in.)




Hide 33257 42.INSTALL OUTER SELECT LEVER

a.
C461178N01
0.427,0.031 0.708,0.385 0.281,0.354 18 false i 3.51,0.031 3.792,0.385 0.281,0.354 18 false ii

i.

Clean the bolt hole of the outer select lever.


ii.

Install the outer select lever and inner select lever to the front transaxle (MTM) case as shown in the illustration.



Hide 43.INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.
C461179C01
1.938,0.5 2.656,0.5 true 2.031,1.167 2.865,1.167 true 6.667,1.25 6.5,1.25 6.5,1.25 6.5,1.417 true 2.146,3.49 2.146,3.281 false 6.604,0.281 6.719,0.281 6.719,0.281 6.719,0.448 true 0.417,0.042 0.563,0.313 0.146,0.271 18 false i 0.552,2.01 0.823,2.271 0.271,0.26 18 false ii 3.938,2.01 4.167,2.281 0.229,0.271 18 true iii 2.698,0.396 2.906,0.573 0.208,0.177 10 false *1 6.719,1.146 6.896,1.333 0.177,0.188 10 true *3 2.896,1.063 3.104,1.24 0.208,0.177 10 false *2 2.083,3.479 2.292,3.656 0.208,0.177 10 false *a 6.396,0.177 6.573,0.365 0.177,0.188 10 true *4
*1 Shift and Select Lever Shaft Assembly *2 Shift Inter Lock Plate
*3 Inner Select Lever *4 No. 3 Gear Shift Head
*a Adhesive - -
V113147

Turn - -


i.

Turn the shift and select lever shaft assembly and shift inter lock plate counterclockwise, and install them to the front transaxle (MTM) case as shown in the illustration.

HINT:

When installing the shift inter lock plate, make sure to engage it with the inner select lever and 3 gear shift heads.



ii.

Apply adhesive to the inner select lever set bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the inner select lever set bolt immediately after applying adhesive to prevent foreign matter from attaching to it.



iii.

Using a 6 mm hexagon socket wrench, install the inner select lever set bolt.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)



Hide 33240 44.INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)

Hide 33211 45.INSTALL REVERSE SHIFT FORK

a.
C461180N01
0.573,0.156 0.854,0.51 0.281,0.354 18 false i 3.833,0.156 4.115,0.51 0.281,0.354 18 false ii 0.552,2.667 0.833,3.021 0.281,0.354 18 false iii 2.781,4.542 3.24,4.74 0.458,0.198 10 false (A)

i.

Secure the No. 4 gear shift fork shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



ii.

Install the reverse shift fork to the No. 4 gear shift fork shaft as shown in the illustration.

NOTICE:

Confirm the installation direction.



iii.

Using a 5 mm pin punch and a hammer, install the slotted spring pin to the reverse shift fork.

Standard Depth (A):

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)




Hide 46.INSTALL REVERSE SHIFT FORK SHAFT ASSEMBLY

a.
C461181C01
0.427,0.042 0.708,0.396 0.281,0.354 18 false i 3.24,0.042 3.521,0.396 0.281,0.354 18 false ii
V100135

Gear Oil - -


i.

Coat the reverse shift fork shaft assembly with gear oil.


ii.

Install the reverse shift fork shaft assembly to the front transaxle (MTM) case.



Hide 33402 47.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C461182C01
4.802,4.865 4.802,4.76 4.802,4.76 4.948,4.76 true 5.063,3.76 5.063,3.49 5.063,3.49 5.323,3.49 true 0.427,0.031 0.708,0.385 0.281,0.354 18 false i 4.417,0.021 4.698,0.375 0.281,0.354 18 false ii 1.667,2.698 2.427,3.115 0.76,0.417 18 false iii, iv 5.094,4.781 5.406,4.979 0.313,0.198 10 false *a 4.74,4.875 5.052,5.073 0.313,0.198 10 false *c 5,3.781 5.188,3.948 0.188,0.167 10 true *b
*a Parallel *b Reverse Idler Gear Shaft Bolt Hole
*c Screw Hole - -
V100136

Gear Oil - -


i.

Clean the reverse idler gear shaft bolt hole.


ii.

Apply gear oil to all sliding and rotating parts.


iii.

Install the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft to the front transaxle (MTM) case as shown in the illustration.

NOTICE:

Make sure that the reverse idler gear shaft bolt hole is parallel to the screw hole on the front transaxle (MTM) case.



iv.

Raise the edge of the reverse shift arm bracket assembly and install it to the reverse shift fork shaft assembly.



Hide 48.CLEAN TRANSMISSION CASE

a.
C461153C01
0.427,0.052 0.708,0.406 0.281,0.354 18 false i
V100145

Area to be cleaned - -


i.

Clean and degrease the contact surfaces of the front transaxle (MTM) case and manual transmission case.



Hide 33111 49.INSTALL MANUAL TRANSMISSION CASE

a.
C461183C01
2.479,1.573 2.479,1.792 true 0.427,0.052 0.813,0.385 0.385,0.333 18 false i 3.417,0.031 3.844,0.354 0.427,0.323 18 false ii 2.031,2.177 2.417,2.49 0.385,0.313 18 false iii 1.302,4.01 1.563,4.302 0.26,0.292 18 false iv 2.406,1.792 2.615,2 0.208,0.208 10 false *a
*a Seal Packing - -
V113147

Install in this Direction
V100135

Push
V100136

Pull
V113148

Turn


i.

Apply seal packing to the manual transmission case as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Standard Seal Diameter:

1.2 mm (0.0472 in.)


NOTICE:
·

Make sure to overlap the start and end points of the seal packing.

·

After applying seal packing, install the manual transmission case to the front transaxle case within 3 minutes and tighten the bolts within 10 minutes.




ii.

Push the outer No. 1 shift lever and temporarily install the manual transmission case.

HINT:

Pushing on the outer No. 1 shift lever allows the manual transmission case to be temporarily installed.



iii.

Pull the outer No. 1 shift lever out and turn it counterclockwise.


iv.

Install the manual transmission case to the front transaxle (MTM) case with the 16 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)



Hide 33253F 50.INSTALL OUTER SHIFT LEVER E-RING

Hide 43420H 51.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C461184N01
2.771,1.615 2.167,1.615 2.167,1.615 2.167,1.115 true 2.438,1.604 2.438,1.063 true 2.615,1.604 2.615,0.958 true 5.677,1.396 6.135,1.594 0.458,0.198 10 false (A) 0.417,0.031 0.698,0.385 0.281,0.354 18 false i 2.833,1.51 3.292,1.708 0.458,0.198 10 false SST

i.

Using SST and a hammer, install a new front drive shaft oil seal LH to the manual transmission case.

SST
09631-12090  
09950-60011  (09951-00480, 09951-00600, 09952-06010)
09950-70010  (09951-07100)

Standard Depth (A):

2.3 to 3.3 mm (0.0906 to 0.130 in.)


NOTICE:
C381409C09
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.969 2.406,1.198 0.281,0.229 10 false *c 1.594,1.146 1.875,1.375 0.281,0.229 10 false *c 0.406,0.646 0.865,0.844 0.458,0.198 10 false SST 1.917,0.646 2.375,0.844 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


·

Make sure that the outer lip of the front drive shaft oil seal LH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal LH.

·

Do not install the front drive shaft oil seal LH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal LH.

·

Do not damage the front drive shaft oil seal LH lip.





Hide 43410M 52.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C461185N01
2.281,1.573 1.865,1.573 1.865,1.573 1.865,1.052 true 2.135,1.563 2.135,1.063 true 5.198,1.229 5.01,1.229 5.01,1.229 5.01,0.833 true 0.417,0.031 0.698,0.385 0.281,0.354 18 false i 2.344,1.458 2.802,1.656 0.458,0.198 10 false SST 5.25,1.125 5.708,1.323 0.458,0.198 10 false SST 4.635,1.417 5.052,1.667 0.417,0.25 10 false (A)

i.

Using SST and a hammer, install a new front drive shaft oil seal RH to the front transaxle (MTM) case.

SST
09223-51010  
09950-60011  (09951-00180)
09950-70010  (09951-07100)

Standard Depth (A):

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
C381409C09
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.969 2.406,1.198 0.281,0.229 10 false *c 1.594,1.146 1.875,1.375 0.281,0.229 10 false *c 0.406,0.646 0.865,0.844 0.458,0.198 10 false SST 1.917,0.646 2.375,0.844 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


·

Make sure that the outer lip of the front drive shaft oil seal RH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal RH.

·

Do not install the front drive shaft oil seal RH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal RH.

·

Do not damage the front drive shaft oil seal RH lip.





Hide 33275C 53.INSTALL SHIFT DETENT BALL

a.
C461186C01
2.052,1.646 2.052,1.448 false 0.552,0.167 1.302,0.469 0.75,0.302 18 false i, iv 3.698,0.156 4.448,0.458 0.75,0.302 18 false ii, iii 1.625,2.094 2.688,2.406 1.063,0.313 18 false v, vi 1.99,1.656 2.302,1.854 0.313,0.198 10 false *a
*a Adhesive - -


i.

Apply adhesive to the 2 shift detent ball plugs.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Make sure to install the 2 shift detent ball plugs immediately after applying adhesive to prevent foreign matter from attaching to it.



ii.

Install the 2 shift detent balls and 2 shift detent ball compression springs to the manual transmission case.

NOTICE:

Be careful not to drop the shift detent balls into the manual transmission case.



iii.

Using a 6 mm hexagon socket wrench, install the 2 shift detent ball plugs to the manual transmission case.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


iv.

Apply adhesive to the shift detent ball plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Make sure to install the shift detent ball plug immediately after applying adhesive to prevent foreign matter from attaching to it.



v.

Install the shift detent ball and shift detent ball compression spring to the manual transmission case.

NOTICE:

Be careful not to drop the shift detent ball into the manual transmission case.



vi.

Using a 6 mm hexagon socket wrench, install the shift detent ball plug to the manual transmission case.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)



Hide 33292A 54.INSTALL LOCK BALL PIN

a.
C461187C01
2.021,2.135 2.021,1.865 false 0.427,0.021 1.156,0.344 0.729,0.323 18 false i 4.01,0.031 4.771,0.375 0.76,0.344 18 false ii, iii 1.948,2.135 2.146,2.323 0.198,0.188 10 false *a
*a Adhesive - -


i.

Apply adhesive to the shift and select lever shaft with head straight screw plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Make sure to install the shift and select lever shaft with head straight screw plug immediately after applying adhesive to prevent foreign matter from attaching to it.



ii.

Install the lock ball pin and shift and select lever shaft compression spring to the manual transmission case.


iii.

Using a 10 mm hexagon socket wrench, install the shift and select lever shaft with head straight screw plug to the manual transmission case.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)



Hide 33451H 55.INSTALL REVERSE IDLER GEAR SHAFT BOLT

a.
C461188C01
2.115,1.99 2.115,1.76 false 2,1.458 2,1.229 false 1.927,1.458 2.24,1.656 0.313,0.198 10 false *a 0.417,0.031 0.698,0.385 0.281,0.354 18 false i 4,0.042 4.281,0.396 0.281,0.354 18 false ii
*a Adhesive - -


i.

Apply adhesive to the reverse idler gear shaft bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the reverse idler gear shaft bolt immediately after applying adhesive to prevent foreign matter from attaching to it.



ii.

Install the reverse idler gear shaft bolt and a new gasket to the manual transmission case.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)



Hide 33290 56.INSTALL NO. 1 LOCK BALL ASSEMBLY

a.
C461189C01
2.396,1.271 2.396,1.469 false 0.427,0.042 0.906,0.354 0.479,0.313 18 false i 4.177,0.052 4.396,0.354 0.219,0.302 18 false ii 2.333,1.479 2.646,1.677 0.313,0.198 10 false *a
*a Adhesive - -


i.

Apply adhesive to the No. 1 lock ball assembly.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Make sure to install the No. 1 lock ball assembly immediately after applying adhesive to prevent foreign matter from attaching to it.



ii.

Install the No. 1 lock ball assembly to the manual transmission case.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)



Hide 31121 57.INSTALL NO. 1 CLUTCH HOUSING COVER

Hide 58.INSTALL RELEASE CYLINDER BLEEDER PLUG

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

Hide 31478 59.INSTALL RELEASE CYLINDER BLEEDER PLUG CAP

Hide 31400 60.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Z101186

Click here(Click here)

Hide 31126B 61.INSTALL CLUTCH TUBE BOOT

Hide 31483 62.TEMPORARILY INSTALL BLEEDER CLUTCH RELEASE TUBE

Z101186

Click here(Click here)

Hide 31407B 63.TEMPORARILY INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 31483 64.FULLY TIGHTEN BLEEDER CLUTCH RELEASE TUBE

Z101186

Click here(Click here)

Hide 65.APPLY GREASE

Z101186

Click here(Click here)

Hide 31407B 66.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 67.INSPECT CLUTCH PIPE LINE

Z101186

Click here(Click here)

Hide 31407B 68.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 69.INSTALL WIRE HARNESS CLAMP BRACKET

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

Hide 335A0 70.INSTALL CONTROL CABLE BRACKET ASSEMBLY

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)

Hide 84545 71.INSTALL NEUTRAL POSITION SWITCH

a.
C461190N01
0.417,0.031 0.698,0.385 0.281,0.354 18 false i

i.

Using SST, install the neutral position switch and a new gasket to the manual transmission case.

SST
09817-16011  

Torque:
40.2 N*m (410 kgf*cm, 30 ft.*lbf)



Hide 84210 72.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
C461191N01
0.427,0.021 0.708,0.375 0.281,0.354 18 false i

i.

Using a 27 mm deep socket wrench, install the back-up light switch assembly and a new gasket to the manual transmission case.

Torque:
40.2 N*m (410 kgf*cm, 30 ft.*lbf)



Hide 89413B 73.INSTALL TRANSMISSION REVOLUTION SENSOR

a.
C462160C01
5.396,1.531 5.396,1.313 false 0.417,0.031 0.698,0.385 0.281,0.354 18 false i 3.958,0.042 4.24,0.396 0.281,0.354 18 false ii 1.844,1.99 2.125,2.344 0.281,0.354 18 false iii 5.344,1.531 5.656,1.729 0.313,0.198 10 false *a
*a Adhesive - -
V100135

Gear Oil - -


i.

Coat a new O-ring with gear oil and install it to the transmission revolution sensor.

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Apply adhesive to the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the bolt immediately after applying adhesive to prevent foreign matter from attaching to it.



iii.

Install the transmission revolution sensor to the manual transmission case with the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)

NOTICE:

Be careful not to damage the O-ring.




Hide 33101A 74.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.
C466872N01
0.427,0.031 0.708,0.385 0.281,0.354 18 false i

i.

Install the manual transmission filler plug and a new gasket to the manual transmission case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Face the tapered side of the gasket toward the manual transmission case.




Hide 33101B 75.INSTALL MANUAL TRANSMISSION DRAIN PLUG

a.
C466873N01
0.427,0.042 0.708,0.396 0.281,0.354 18 false i

i.

Install the manual transmission drain plug and a new gasket to the manual transmission case.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

NOTICE:

Face the tapered side of the gasket toward the manual transmission case.