Home › Drivetrain › CLUTCH › CLUTCH UNIT › from 2021.07
RM3700E _52 Drivetrain _104786 CLUTCH _0480197 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C459855N02
3.51,4.698 4.302,4.875 0.792,0.177 0.76,5 1.427,5.198 0.667,0.198 3.51,4.958 4.344,5.271 0.833,0.313 3.469,4.917 4.385,5.313 0.917,0.396 5.448,1.708 6.24,1.885 0.792,0.177 1.344,1.385 2.156,1.552 0.813,0.167 1.385,0.885 2.219,1.219 0.833,0.333 1.344,0.844 2.26,1.26 0.917,0.417 1.229,3.146 1.5,3.146 1.5,3.146 1.5,3 false 2.323,3.75 2.49,3.75 2.49,3.75 2.49,3.667 false 2.365,1.792 2.604,1.792 2.604,1.792 2.927,1.625 false 4.771,2.604 4.771,2.104 4.771,2.104 4.938,2.104 false 5.292,2.906 5.417,2.906 false 6.625,0.229 6.854,0.229 false 5.313,4.083 5.646,4.083 false 2.875,3.885 3.302,4.781 3.302,4.781 3.51,4.781 false 1.438,5.094 1.771,5.094 false 5.271,2.302 5.271,1.802 5.271,1.802 5.438,1.802 false 2.156,1.469 2.396,1.469 2.396,1.469 2.396,1.344 false 2.833,4.271 3.219,5.115 3.219,5.115 3.5,5.115 true 2.219,1.052 2.75,1.052 false 2.5,1.052 2.5,1.115 2.5,1.115 2.813,1.115 false 2.823,1.073 3.771,0.729 3.771,0.729 4.063,0.729 false 1.583,4.208 1.844,4.208 1.844,4.208 2.625,4.333 false 1.031,2.948 1.313,3.302 0.281,0.354 18 false 1 1.833,3.563 2.458,3.833 0.625,0.271 18 false 2, 3 6.031,0.052 6.719,0.406 0.688,0.354 18 false 9, 11 2.156,1.625 2.958,2.01 0.802,0.385 18 false 4 5.01,1.927 5.292,2.281 0.281,0.354 18 false 5 4.427,0.552 5.74,0.906 1.313,0.354 18 false 6, 8 5.75,2.729 6.927,3.333 1.177,0.604 18 false 7, 10, 12 1.229,4.052 1.615,4.406 0.385,0.354 18 false 13 5.698,3.906 6.083,4.26 0.385,0.354 18 false 14 5.344,2.26 5.656,2.458 0.313,0.198 10 false x2 3.542,4.698 4.771,4.854 1.229,0.156 8 false 19.1 (195, 14) 0.802,5.01 2.031,5.167 1.229,0.156 8 false 12 (122, 9) 3.542,4.958 4.771,5.115 1.229,0.156 8 false 15.2 (155, 11) 3.542,5.094 4.771,5.25 1.229,0.156 8 false 13.4 (137, 10)* 1.427,0.906 2.24,1.125 0.813,0.219 8 false 15.2 (155, 11) 1.979,1.708 2.135,1.906 0.156,0.198 10 false ● 1.396,1.385 2.208,1.604 0.813,0.219 8 false 22.5 (229, 17) 2.5,1.188 2.813,1.385 0.313,0.198 10 false x3 1.115,1.375 1.49,1.573 0.375,0.198 10 false ●★ 2.938,3.76 3.25,3.958 0.313,0.198 10 false x6 1.427,1.042 2.24,1.26 0.813,0.219 8 false 13.4 (137, 10)* 5.49,1.708 6.302,1.927 0.813,0.219 8 false 16.7 (170, 12)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CLUTCH DISC ASSEMBLY 31250 (Click here) - -
2 INSTALL CLUTCH COVER ASSEMBLY 31210 (Click here) - -
3 INSPECT AND ADJUST CLUTCH COVER ASSEMBLY 31210 (Click here) - -
4 CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY 31400 (Click here) - -
5 CLUTCH TUBE BOOT 31126B - - -
6 TEMPORARILY INSTALL BLEEDER CLUTCH RELEASE TUBE 31483 (Click here) - -
7 TEMPORARILY INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY 31407B (Click here) - -
8 FULLY TIGHTEN BLEEDER CLUTCH RELEASE TUBE 31483 (Click here) - -
9 APPLY GREASE - (Click here) - -
10 REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY 31407B (Click here) - -
11 INSPECT CLUTCH PIPE LINE - (Click here) - -
12 INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY 31407B (Click here) - -
13 CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE 31482 (Click here) - -
14 MANUAL TRANSAXLE ASSEMBLY 30300 - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
* For use with union nut wrench ● Non-reusable part
V100135

Clutch Spline Grease ★ Precoated part

CAUTION / NOTICE / HINT

NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C459858C01
2.771,1.208 3.104,1.208 false 5.083,0.313 5.417,0.313 false 4.448,0.188 4.781,0.188 false 5.417,1.323 5.417,0.99 false 3.167,1.104 3.625,1.302 0.458,0.198 10 false SST 5.458,0.198 5.917,0.396 0.458,0.198 10 false *1 4.281,0.094 4.74,0.292 0.458,0.198 10 false *2 5.281,1.344 5.74,1.542 0.458,0.198 10 false SST 4.458,0.792 4.917,0.99 0.458,0.198 10 false *a 0.438,0 0.719,0.354 0.281,0.354 18 false i
*1 Clutch Disc Assembly *2 Flywheel Sub-assembly
*a Flywheel Sub-assembly Side - -


i.

Insert SST into the clutch disc assembly, then insert them both into the flywheel sub-assembly.

SST
09301-00210  

NOTICE:
·

Keep the lined part of the clutch disc assembly, the pressure plate, and the surface of the flywheel sub-assembly away from oil and foreign matter.

·

Insert the clutch disc assembly in the correct direction.





Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C459859C01
3.865,0.896 4.219,0.667 4.219,0.667 4.385,0.667 true 3.063,1.229 2.75,1.583 2.75,1.583 3.115,1.24 true 0.438,0.01 1.813,0.365 1.375,0.354 18 false i, ii 4.438,0.563 4.896,0.76 0.458,0.198 10 false SST 4.073,0.125 4.729,0.323 0.656,0.198 10 false 1 (*b), 4 4.104,1.521 4.563,1.719 0.458,0.198 10 false 2 2.656,0.844 3.115,1.042 0.458,0.198 10 false 3 4.406,0.771 4.865,0.969 0.458,0.198 10 false 5 3.021,1.583 3.479,1.781 0.458,0.198 10 false 6 2.99,0.104 3.448,0.302 0.458,0.198 10 false 7 2.583,1.563 3.042,1.76 0.458,0.198 10 false *a
*a Matchmark *b Temporarily Tighten


i.

Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.


ii.

Following the procedure shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

SST
09301-00210  

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.





Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C462170N01
5.583,1.021 5.958,0.667 5.958,0.667 6.135,0.667 true 0.458,0.021 0.74,0.375 0.281,0.354 18 false i 4.083,0.01 4.365,0.365 0.281,0.354 18 false ii 6.208,0.563 6.667,0.76 0.458,0.198 10 false SST

i.

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

Non-alignment:

0.5 mm (0.0197 in.) or less



ii.

If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  



Hide 31400 4.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

a.
C459860N01
0.438,0 0.719,0.354 0.281,0.354 18 false i 3.427,0.021 3.927,0.302 0.5,0.281 18 true ii, iii

i.

Temporarily tighten the bleeder clutch release tube to a new clutch release cylinder with bearing assembly.

NOTICE:

Do not allow any foreign matter such as dirt or dust to enter the bleeder clutch release tube from the connecting part.



ii.

Clean and degrease all installation surfaces for the clutch release cylinder with bearing assembly.


iii.

Install the clutch release cylinder with bearing assembly with 3 new bolts.

Torque:
22.5 N*m (229 kgf*cm, 17 ft.*lbf)

NOTICE:
·

The clutch release cylinder with bearing assembly and installation bolts cannot be reused and must be replaced with new ones.

·

Clean and degrease all installation surfaces and make sure that the clutch release cylinder with bearing assembly fits securely with the manual transaxle assembly during installation. The first bolt should be tightened by hand while holding the clutch release cylinder with bearing assembly.

·

Ensure that none of the clutch spline grease adheres to the clutch release cylinder with bearing assembly.

·

The clutch release cylinder with bearing assembly cannot be disassembled.





Hide 31126B 5.INSTALL CLUTCH TUBE BOOT

Hide 31483 6.TEMPORARILY INSTALL BLEEDER CLUTCH RELEASE TUBE

a.
C462149N01
0.417,0.031 0.698,0.385 0.281,0.354 18 false i

i.

Temporarily install the bleeder clutch release tube to the clutch release bleeder sub-assembly.



Hide 31407B 7.TEMPORARILY INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C462150N01
0.427,0.031 0.708,0.385 0.281,0.354 18 false i

i.

Temporarily install the clutch release bleeder sub-assembly with the 2 bolts.



Hide 31483 8.FULLY TIGHTEN BLEEDER CLUTCH RELEASE TUBE

a.
C461142C01
0.427,0.031 0.708,0.385 0.281,0.354 18 false i 4.385,0.198 4.563,0.375 0.177,0.177 10 true *a
*a Torque Wrench Fulcrum Length - -


i.

Using a 10 mm union nut wrench, tighten the bleeder clutch release tube to the clutch release cylinder with bearing assembly.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the bleeder clutch release tube.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)





Hide 9.APPLY GREASE

a.
C461143C01
0.406,0.031 0.625,0.323 0.219,0.292 18 false i
V100135

Clutch Spline Grease - -


i.

Apply clutch spline grease to the input shaft splines.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent




Hide 31407B 10.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C462154N01
0.406,0.031 0.542,0.323 0.135,0.292 18 true i 4,0.031 4.177,0.302 0.177,0.271 18 true ii

i.

Using a 10 mm union nut wrench, separate the clutch release bleeder sub-assembly from the bleeder clutch release tube.


ii.

Remove the 2 bolts and clutch release bleeder sub-assembly from the manual transaxle assembly.



Hide 11.INSPECT CLUTCH PIPE LINE

a.
C461144N01
0.406,0.031 1.781,0.385 1.375,0.354 18 false i, ii

i.

Using SST, apply pressure of 100 kPa (1.0 kgf/cm2, 15 psi) to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.

SST
09992-00242  


ii.

If the pressure drops, replace the bleeder clutch release tube.



Hide 31407B 12.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C462151C01
5.573,2.552 5.885,2.75 0.313,0.198 10 false *a 0.406,0.031 0.771,0.385 0.365,0.354 18 true i, ii 3.917,0.031 4.156,0.323 0.24,0.292 18 true iii
*a Torque Wrench Fulcrum Length - -


i.

Temporarily install the bleeder clutch release tube to the clutch release bleeder sub-assembly.


ii.

Install the 2 bolts and clutch release bleeder sub-assembly.

Torque:
16.7 N*m (170 kgf*cm, 12 ft.*lbf)


iii.

Using a 10 mm union nut wrench, install the bleeder clutch release tube.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the bleeder clutch release tube.

·

Do not allow any foreign matter such as dirt or dust to enter the bleeder clutch release tube from the connecting part.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)





Hide 31482 13.INSTALL CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

a.
C462152C01
5.469,2.49 5.781,2.688 0.313,0.198 10 false *a 3.604,0.031 4.396,0.313 0.792,0.281 18 true ii, iii, iv 0.146,0.083 0.427,0.427 0.281,0.344 18 false i
*a Torque Wrench Fulcrum Length - -


i.

Install the clamp to the clutch release cylinder to flexible hose tube.


ii.

Temporarily install the clutch release cylinder to flexible hose tube to the clutch release bleeder sub-assembly.


iii.

Install the clutch release cylinder to flexible hose tube to the manual transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


iv.

Using a 10 mm union nut wrench, install the clutch release cylinder to flexible hose tube to the clutch release bleeder sub-assembly.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the clutch release cylinder to flexible hose tube.

·

Do not allow any foreign matter such as dirt or dust to enter the clutch release cylinder to flexible hose tube from the connecting part.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)