| *1 | OUTPUT SHAFT | *2 | MIDDLE RING |
| *3 | OUTER RING | *4 | INNER RING |
|
Gear Oil | ● | Non-reusable part |
33321N
1.INSTALL FRONT OUTPUT SHAFT BEARING
Using SST and a press, install a new front output shaft bearing to the output shaft.
33345
2.INSTALL 1ST GEAR BUSHING
|
Gear Oil | - | - |
Coat the 1st gear bushing with gear oil.
Install the 1st gear bushing to the output shaft.
33335C
3.INSTALL 1ST GEAR NEEDLE ROLLER BEARING
|
Gear Oil | - | - |
Coat the 1st gear needle roller bearing with gear oil.
Install the 1st gear needle roller bearing to the output shaft.
33335
4.INSTALL 1ST GEAR
|
Gear Oil | - | - |
Coat the 1st gear with gear oil.
Install the 1st gear to the output shaft as shown in the illustration.
Confirm the installation direction.
33037B
5.INSTALL NO. 1 SYNCHRONIZER RING SET (for 1st Gear)
| *a | Outer Ring | *b | Middle Ring |
| *c | Inner Ring | - | - |
|
Gear Oil | - | - |
Coat the No. 1 synchronizer ring set (inner ring, middle ring and outer ring) with gear oil.
Install the inner ring to the 1st gear.
Install the middle ring to the 1st gear.
Engage the claws of the middle ring to the grooves of the 1st gear.
Install the outer ring to the 1st gear.
Align the claws of the inner ring with the grooves of the outer ring before installing the outer ring.
33361
6.INSTALL NO. 1 TRANSMISSION CLUTCH HUB
|
|
33365
7.INSTALL NO. 1 SYNCHROMESH SHIFTING KEY
33331
8.INSTALL REVERSE GEAR
|
Gear Oil | - | - |
Coat the reverse gear and No. 1 transmission clutch hub with gear oil.
Install the reverse gear to the No. 1 transmission clutch hub as shown in the illustration.
Confirm the installation direction.
33037B
9.INSTALL NO. 1 SYNCHRONIZER RING SET (for 2nd Gear)
| *a | Inner Ring | *b | Inner Ring |
| *c | Cutout | - | - |
|
Gear Oil | - | - |
Coat the reverse gear cone and No. 1 synchronizer ring set (inner ring, middle ring and outer ring) with gear oil.
Install the outer ring to the No. 1 transmission clutch hub.
Align the protrusion of the outer ring with the cutout of the No. 1 transmission clutch hub before installing the outer ring.
Install the middle ring to the outer ring.
Install the inner ring to the middle ring.
Align the cutout of the outer ring with the protrusion of the inner ring before installing the inner ring.
33356A
10.INSTALL 2ND GEAR BEARING INNER RACE
|
Gear Oil | - | - |
Coat the 2nd gear bearing inner race with gear oil.
Install the 2nd gear bearing inner race to the output shaft.
33332B
11.INSTALL 2ND GEAR NEEDLE ROLLER BEARING
|
Gear Oil | - | - |
Coat the 2nd gear needle roller bearing with gear oil.
Install the 2nd gear needle roller bearing to the output shaft.
33332
12.INSTALL 2ND GEAR
| *a | Groove | *b | Claw |
|
Gear Oil | - | - |
Coat the 2nd gear with gear oil.
Install the 2nd gear to the output shaft.
Align the claw of the middle ring with the groove of the 2nd gear before installing the 2nd gear.
33423A
13.INSTALL 3RD DRIVEN GEAR
|
|
Using SST and a press, install the 3rd driven gear to the output shaft as shown in the illustration.
33431C
14.INSTALL OUTPUT GEAR SPACER
33422B
15.INSTALL 4TH DRIVEN GEAR
|
|
Using SST and a press, install the 4th driven gear to the output shaft as shown in the illustration.
33428C
16.INSTALL 5TH DRIVEN GEAR
|
|
Using SST and a press, install the 5th driven gear to the output shaft as shown in the illustration.
33431C
17.INSTALL OUTPUT GEAR SPACER
33429B
18.INSTALL 6TH DRIVEN GEAR
|
|
Using SST and a press, install the 6th driven gear to the output shaft as shown in the illustration.
33321A
19.INSTALL REAR OUTPUT SHAFT BEARING
Using SST and a press, install a new rear output shaft bearing to the output shaft.
20.INSPECT 2ND GEAR RADIAL CLEARANCE
21.INSPECT 1ST GEAR RADIAL CLEARANCE
22.INSPECT 2ND GEAR THRUST CLEARANCE
23.INSPECT 1ST GEAR THRUST CLEARANCE