| *A | for 2WD | *B | for AWD |
| *C | w/ Differential Pressure Sensor | *D | w/o Differential Pressure Sensor |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 13 | CENTER NO. 1 FLOOR BRACE | 57543C | - | - | - |
| 14 | CENTER NO. 4 ENGINE UNDER COVER | 51447D | - | - | - |
| *A | for TMMF Made | *B | for TMC Made |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
17168
1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
17173
2.INSTALL EXHAUST MANIFOLD TO HEAD GASKET
17141
3.INSTALL EXHAUST MANIFOLD
Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.
Temporarily install the exhaust manifold to the cylinder head sub-assembly with 6 new nuts.
Tighten the 6 nuts in the order shown in the illustration.
17118
4.INSTALL MANIFOLD STAY
Temporarily install the manifold stay to the exhaust manifold and cylinder block sub-assembly with the bolt and nut.
Tighten the bolt and nut in the order shown in the illustration.
17167
5.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
6.INSTALL NO. 1 VACUUM PIPE (w/ Differential Pressure Sensor)
| *a | 14 mm Union Nut Wrench | *b | Torque Wrench Fulcrum Length |
Temporarily install a new No. 1 vacuum transmitting pipe sub-assembly to the exhaust manifold with the nut.
Tighten the nut.
Using a 14 mm union nut wrench, tighten the No. 1 vacuum transmitting pipe sub-assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf).
7.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY (w/ Differential Pressure Sensor)
8.INSTALL WIRE HARNESS CLAMP BRACKET
89467B
9.INSTALL AIR FUEL RATIO SENSOR
58151
10.INSTALL NO. 1 FRONT FLOOR HEAT INSULATOR
17410
11.INSTALL FRONT EXHAUST PIPE ASSEMBLY
| *1 | Exhaust Manifold or Front Exhaust Pipe Assembly | *2 | Exhaust Pipe Gasket |
Temporarily install 2 new exhaust pipe gaskets to the exhaust manifold and front exhaust pipe assembly.
Using a plastic hammer and wooden block, tap in each exhaust pipe gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.
Be sure to install the exhaust pipe gasket in the correct direction.
Do not reuse the exhaust pipe gaskets.
Do not damage the exhaust pipe gaskets.
Do not push in the exhaust pipe gaskets by using the exhaust pipes when connecting them.
| *A | for 2WD | *B | for AWD |
| *1 | Exhaust Manifold | *2 | Front Exhaust Pipe Assembly |
| *3 | Exhaust Pipe Gasket | *4 | Tail Exhaust Pipe Assembly |
| *a | Space between Flanges: 8.5 mm (0.335 in.) | *b | Space between Flanges: 6.5 mm (0.256 in.) |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum Free Length (Front) | 41.5 mm (1.63 in.) |
| Minimum Free Length (Rear) | 38.5 mm (1.52 in.) |
1, If the free length is less than the minimum, replace the compression spring.
Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.
Install the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts.
After installation, check that the space between the flanges of the exhaust manifold and front exhaust pipe assembly is consistent front-to-rear and left-to-right.
Install the front exhaust pipe assembly to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.
After installation, check that the space between the flanges of the front exhaust pipe assembly and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.
Engage the clamp.
Connect the No. 2 air fuel ratio sensor connector.
12.INSPECT FOR EXHAUST GAS LEAK
57543C
13.INSTALL CENTER NO. 1 FLOOR BRACE (for TMMF Made)
51447D
14.INSTALL CENTER NO. 4 ENGINE UNDER COVER