| *A | for TMC Made | *B | for TMMF Made |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 6 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | 51201 | ( )
|
- | - |
| 7 | CONNECT ENGINE MOVING CONTROL ROD | 12363A | - | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
| *A | for TMMF Made | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 16 | FRONT FENDER LINER LH | 53876A | - | - | - |
| 17 | FRONT FENDER LINER RH | 53875A | - | - | - |
| 18 | FRONT WHEELS | - | - | - | - |
| *A | for LHD | *B | for RHD |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
| *A | for TMC Made | *B | for TMMF Made |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
48069
3.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
|
|
48068
4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
12363A
5.INSTALL ENGINE MOVING CONTROL ROD
51201
6.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
| *a | Engine Lifter | *b | Attachment |
|
Attachment placement location | - | - |
Slowly jack up the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.
The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.
If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments to keep the front suspension crossmember sub-assembly level.
Make sure that the front suspension crossmember sub-assembly not hit the protrusion of the reinforcement.
| *a | Correct |
| *b | Incorrect |
After installation, check that the claws of the steering column hole cover base are not disengaged.
Install the front suspension crossmember sub-assembly to the vehicle body with the 10 bolts (A).
12363A
7.CONNECT ENGINE MOVING CONTROL ROD
48068
9.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
45047
10.CONNECT TIE ROD END SUB-ASSEMBLY LH
Connect the tie rod end sub-assembly LH to the steering knuckle LH with the nut.
Do not damage the ball joint dust cover.
Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.
Install a new cotter pin.
45046
11.CONNECT TIE ROD END SUB-ASSEMBLY RH
12.INSTALL STEERING KNUCKLE SEAL (for TMMF Made)
|
|
48810
13.CONNECT FRONT STABILIZER LINK ASSEMBLY LH
|
|
48820B
14.CONNECT FRONT STABILIZER LINK ASSEMBLY RH
82715W
15.INSTALL WIRING HARNESS CLAMP BRACKET
53876A
16.INSTALL FRONT FENDER LINER LH
53875A
17.INSTALL FRONT FENDER LINER RH
18.INSTALL FRONT WHEELS
45259A
20.INSTALL COLUMN HOLE COVER SILENCER SHEET
48068
23.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
51447D
24.INSTALL CENTER NO. 4 ENGINE UNDER COVER
51442C
25.INSTALL ENGINE UNDER COVER LH
51441C
26.INSTALL ENGINE UNDER COVER RH
51410
27.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
28.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT