Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING VALVE › from 2021.07
RM3700E _53 Suspension _105068 TIRE PRESSURE MONITORING _0480805 TIRE PRESSURE WARNING VALVE A

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING VALVE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C438446N02
3.844,0.729 4.844,0.896 1,0.167 3.083,0.531 4.917,1.969 1.833,1.438 4.146,4.229 5.177,4.396 1.031,0.167 3.625,1.313 3.917,1.313 false 3.729,2.219 4.135,2.219 true 5.875,4.052 6.156,3.813 6.156,3.813 6.323,3.813 false 5.677,4.615 5.844,4.615 5.844,4.615 6.021,4.333 false 6.479,0.198 6.813,0.198 false 6.458,0.656 6.75,0.656 false 3.406,1.146 3.51,0.802 3.51,0.802 3.677,0.802 false 5.458,3.51 5.896,3.104 5.896,3.104 6.063,3.104 true 3.885,1.719 4.177,1.719 false 0.552,1.135 0.844,1.135 false 4.917,1.406 5.042,1.406 false 2.427,3.396 2.719,3.396 false 5.188,4.313 5.354,4.313 5.354,4.313 5.563,3.844 true 4.24,1.177 4.521,1.531 0.281,0.354 18 false 1 3.354,2.073 3.51,2.271 0.156,0.198 10 false ● 3.49,2.031 3.677,2.302 0.188,0.271 18 true 2 4.219,4.229 5.354,4.396 1.135,0.167 8 false 4.0 (41, 35 in.*lbf) 6.656,3.75 6.813,3.948 0.156,0.198 10 false ● 6.823,3.677 7.01,3.948 0.188,0.271 18 false 4 5.479,4.448 5.667,4.719 0.188,0.271 18 false 5 5.979,0.073 6.813,0.427 0.833,0.354 18 false 7, 8 6.25,0.521 6.604,0.844 0.354,0.323 18 false 9 3.719,0.708 3.875,0.906 0.156,0.198 10 false ● 3.885,0.729 5.104,0.885 1.219,0.156 8 false 1.2 (12, 11 in.*lbf) 6.115,3.042 6.427,3.24 0.313,0.198 10 false *1 4.26,1.615 4.698,1.802 0.438,0.188 10 false ● *2 0.354,1.042 0.667,1.24 0.313,0.198 10 false *3 4.135,4.406 4.448,4.604 0.313,0.198 10 false *4 2.198,3.26 2.552,3.583 0.354,0.323 18 false 6 5.281,1.271 5.635,1.594 0.354,0.323 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 TIRE PRESSURE WARNING TRANSMITTER - (Click here) - -
2 GROMMET - (Click here) - -
3 TIRE PRESSURE WARNING VALVE AND TRANSMITTER - (Click here) - -
4 VALVE CORE - (Click here) - -
5 TIRE VALVE CAP - - - -
6 WHEEL ASSEMBLY - - - -
7 INSPECT TIRES - (Click here) -
8 REGISTER TRANSMITTER ID - (Click here) -
9 PERFORM INITIALIZATION - - - (Click here)

*1 WASHER *2 TIRE PRESSURE WARNING VALVE
*3 TIRE *4 NUT
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

CAUTION / NOTICE / HINT

NOTICE:
·

Always use a new bolt, grommet, tubeless tire valve and tire pressure monitor valve when installing the tire pressure warning valve and transmitter.

·

Check that the washer and nut are not damaged, and replace them if necessary.

·

Make sure not to damage the urethane covered backside of the tire pressure warning valve and transmitter (the surface opposite to the side with the ID code) with anything sharp.

·

Write down the ID number before installation.

·

Check that there is no oil, water or lubricant around the rim hole, tire pressure warning valve and transmitter, washer and nut. Failing to do so may result in improper installation.

·

Use only a specified tire valve cap. If an unspecified tire valve cap is used, it may seize to the tire pressure warning valve and transmitter.



PROCEDURE

Hide 1.INSTALL TIRE PRESSURE WARNING TRANSMITTER

a.
C438442N01
2.417,0.063 2.698,0.417 0.281,0.354 18 false i

i.

Using a T10 "TORX" socket wrench, install the tire pressure warning transmitter to the new tire pressure warning valve with a new bolt.

Torque:
1.2 N*m (12 kgf*cm, 11 in.*lbf)



Hide 2.INSTALL GROMMET

Z101186

NOTICE:

A new tire pressure warning valve and transmitter comes with a grommet installed. Make sure not to install an extra grommet.



Hide 3.INSTALL TIRE PRESSURE WARNING VALVE AND TRANSMITTER

a.
C438443C01
1.375,1.708 1.708,1.708 true 2.479,1.542 2.479,1.01 true 4.25,0.958 4.583,0.958 true 5.948,0.573 6.281,0.573 true 5.26,0.49 5.427,0.49 5.427,0.49 5.552,0.927 false 5.125,1.677 5.292,1.677 5.292,1.677 5.573,1.333 true 5.865,1.667 5.865,1.417 false 1.76,1.615 2.073,1.813 0.313,0.198 10 false *a 2.417,1.573 2.729,1.771 0.313,0.198 10 false *b 4.063,0.854 4.375,1.052 0.313,0.198 10 false *1 5.74,0.469 6.052,0.667 0.313,0.198 10 false *c 5.063,0.417 5.375,0.615 0.313,0.198 10 false *2 4.938,1.604 5.25,1.802 0.313,0.198 10 false *3 5.802,1.688 6.115,1.885 0.313,0.198 10 false *4 0.615,0.208 0.896,0.563 0.281,0.354 18 false i 1.802,2.104 2.083,2.458 0.281,0.354 18 false iii 4.396,0.208 4.677,0.563 0.281,0.354 18 false ii
*1 Tire Pressure Warning Transmitter *2 Grommet
*3 Washer *4 Nut
*a Printed Surface *b 7-digit Transmitter ID Number
*c Rim - -


i.

Write down the 7-digit transmitter ID number shown in the illustration.


ii.

Insert the tire pressure warning valve and transmitter with grommet from the inside of the rim.

NOTICE:
·

Make sure that the tire pressure warning valve and transmitter is installed so that the printed surface can be seen. If the tire pressure warning valve and transmitter is installed upside down, it may be damaged or fail to transmit signals when driving at high speeds.

·

Check that there is no deformation or damage to the tire pressure warning valve and transmitter.

·

Check that there is no foreign matter on the grommet and around the rim hole.




iii.

Install the washer to the tire pressure warning valve and transmitter from the outside of the rim, and using an 11 mm deep socket wrench, tighten the nut.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)

NOTICE:
·

No further tightening is required once the nut is tightened to the specified torque.

·

Check that there is no foreign matter on the grommet, washer and nut.





b.
C439866C01
2.865,0.479 3.135,0.188 3.135,0.188 3.302,0.188 false 4.365,0.49 4.635,0.198 4.635,0.198 4.802,0.198 false 3.135,1.115 3.5,1.115 false 4.615,0.667 4.979,0.667 false 0.458,0.083 3.208,0.438 2.75,0.354 18 false i, ii, iii 3.323,0.104 3.635,0.302 0.313,0.198 10 false *a 4.833,0.115 5.146,0.313 0.313,0.198 10 false *a 4.542,1.313 4.854,1.51 0.313,0.198 10 false *b 2.479,1.323 2.792,1.521 0.313,0.198 10 false *b 3.542,1.052 3.854,1.25 0.313,0.198 10 false *c 5.042,0.594 5.354,0.792 0.313,0.198 10 false *c
*a Mount Tool of the Mouting Machine *b 60°
*c Rim - -
V100135

Rim Rotating Direction
V100144

Area for Tire Pressure Warning Valve and Transmitter


i.

Set the tire and disc wheel onto the mounting machine as shown in the illustration.

NOTICE:
·

Position the main body of the tire pressure warning valve and transmitter in the area shown in the illustration.

·

If the tire pressure warning valve and transmitter is positioned outside this area, it will interfere with the tire bead and may be damaged.




ii.

Apply a sufficient coat of soapy water or equivalent to the tire bead and rim.

NOTICE:

Do not apply soapy water or equivalent directly to the tire pressure warning valve and transmitter.



iii.

Using a mounting machine, install the tire to the disc wheel.

NOTICE:
·

Make sure that the tire bead and mount tool do not interfere with the tire pressure warning valve and transmitter.

·

Make sure that the tire pressure warning valve and transmitter is not clamped by the bead and rim.





Hide 4.INSTALL VALVE CORE

a.
C438444N01
0.167,0.229 0.448,0.583 0.281,0.354 18 false i 4.073,0.208 4.354,0.563 0.281,0.354 18 false ii 0.542,2.49 0.969,2.844 0.427,0.354 18 false iii 4.354,2.469 4.781,2.823 0.427,0.354 18 false iv

i.

Install a new valve core.


ii.

Inflate the tire to the specified tire inflation pressure.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


iii.

After the tire is inflated, the nut may be loose. Using an 11 mm deep socket wrench, retighten the nut to the specified torque.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)

NOTICE:

No further tightening is required once the nut is tightened to the specified torque.



iv.

Check the surroundings of the tire pressure warning valve and transmitter for air leaks with soapy water or equivalent.

1. If air is leaking from the valve core, press the valve core several times to remove foreign matter. Replace the valve core as necessary.

2. If air is leaking from around the tire pressure warning valve and transmitter, check if the grommet, washer and nut are not deformed, damaged or contaminated with foreign matter. Replace the grommet, washer or nut as necessary.



Hide 5.INSTALL TIRE VALVE CAP

Hide 6.INSTALL WHEEL ASSEMBLY