Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0442067 BRAKE BOOSTER PUMP A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442508N01
6.438,0.219 6.854,0.219 false 3.208,0.615 3.625,0.615 false 6.208,0.063 6.49,0.417 0.281,0.354 18 false 1 3.688,0.458 3.969,0.813 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PERFORM ACCUMULATOR PRESSURE ZERO DOWN - (Click here) - -
2 HYBRID MOTOR CONTROL INVERTER ASSEMBLY G92A0 - - -

C442509N01
6.458,0.198 6.875,0.198 false 5.031,0.781 4.854,0.198 true 5.25,0.844 5.073,0.188 true 5.469,0.865 5.323,0.188 5.323,0.188 4.25,0.188 true 3.125,2.656 3.125,2.031 3.125,2.031 1.719,2.031 true 2.448,2.604 2.448,2.031 false 3.844,5.51 3.677,5.51 3.677,5.51 3.521,5.365 false 3.198,3.844 3.198,3.458 false 5.75,4.469 5.344,4.469 false 1.938,4.177 1.625,4.177 false 4.802,0.802 4.604,0.198 true 4.031,0.083 4.313,0.438 0.281,0.354 18 false 7 6.25,0.052 6.531,0.406 0.281,0.354 18 false 4 1.458,1.875 1.74,2.229 0.281,0.354 18 false 7 4.188,5.375 4.469,5.729 0.281,0.354 18 false 6 3.135,3.865 3.417,4.219 0.281,0.354 18 false 5 6.063,4.333 6.344,4.688 0.281,0.354 18 false 8 4.708,4.906 4.99,5.26 0.281,0.354 10 false x2 2.208,3.99 2.49,4.344 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

3 FLOOR UNDER WIRE 821H1 (Click here) - -
4 DRAIN BRAKE FLUID - - (Click here) -
5 NO. 1 BRAKE ACTUATOR HOSE 44571A - - -
6 ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE 473A1 (Click here) - -
7 BRAKE LINE - (Click here) - -
8 BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY - (Click here) - -

C442510N01
0.75,3.844 0.75,3.427 false 2.167,4.271 2.583,4.271 false 1.979,1.552 2.208,1.188 2.208,1.188 2.354,1.188 false 5.844,3.792 5.844,3.375 false 6.292,3.75 6.292,3.333 false 2.729,1.083 3.281,1.438 0.552,0.354 18 false 13 0.698,3.906 1.25,4.26 0.552,0.354 18 false 9 2.646,4.146 3.198,4.5 0.552,0.354 18 false 10 5.708,3.833 6.26,4.188 0.552,0.354 18 false 12 6.208,3.813 6.76,4.167 0.552,0.354 18 false 11

Procedure Part Name Code
Z101186

Z101188

Z101187

9 NO. 1 BRAKE ACTUATOR HOSE 44571A - - -
10 NO. 1 BRAKE TUBE CLAMP BRACKET 47381 - - -
11 NO. 2 BRAKE ACTUATOR CASE COLLAR 44521B - - -
12 BRAKE TRACTION ACTUATOR BRACKET BUSH 47999A - - -
13 BRAKE BOOSTER PUMP ASSEMBLY 47070 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster pump assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

Hide G92A0 2.REMOVE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Hide 821H1 3.SEPARATE FLOOR UNDER WIRE

Z101186

CAUTION:

Be sure to wear insulated gloves.



a.
C431716


Hide 4.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 44571A 5.SEPARATE NO. 1 BRAKE ACTUATOR HOSE

a.
C430252


Hide 473A1 6.SEPARATE ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C442511N02
0.333,0.01 0.583,0.26 0.25,0.25 18 false i 3.708,0.021 3.958,0.271 0.25,0.25 18 false ii

i.

Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster pump assembly.


ii.

Remove the bolt to separate the accumulator to brake master cylinder tube.



Hide 7.SEPARATE BRAKE LINE

a.
C442512C02
1.198,3.698 1.708,3.49 true 2.406,4.177 2.271,3.833 true 2.49,3.5 2.813,3.292 true 2.323,3.396 2.563,3.042 true 2.135,3.26 2.094,2.833 true 1.948,3.156 1.677,2.896 true 0.594,0.333 0.833,0.583 0.24,0.25 18 true i 4.042,0.333 4.281,0.583 0.24,0.25 18 true ii 0.563,2.708 1.146,2.958 0.583,0.25 18 true iii, iv 4.01,2.677 4.25,2.927 0.24,0.25 18 true v 0.906,3.635 1.156,3.802 0.25,0.167 10 true *a 2.302,4.219 2.552,4.385 0.25,0.167 10 true *b 2.813,3.24 3.063,3.406 0.25,0.167 10 true *c 2.521,2.833 2.771,3 0.25,0.167 10 true *d 1.979,2.635 2.229,2.802 0.25,0.167 10 true *e 1.521,2.708 1.771,2.875 0.25,0.167 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH *d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH *f To Front Wheel Cylinder Assembly RH
V113147

Release the lock lever
V113148

Disconnect the connector


i.

Release the lock lever and disconnect the connector from the brake booster pump assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Release the lock lever and disconnect the connector from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



iii.

Use tags or make a memo to identify the places to reconnect the brake lines.


iv.

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


v.

Disengage the clamp to separate the brake line.



Hide 8.REMOVE BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY

a.
C442513N02
1.406,1.406 1.698,1.656 0.292,0.25 18 false ii 2.427,1.198 2.719,1.448 0.292,0.25 18 false i 5.146,1.094 5.438,1.344 0.292,0.25 18 true iii 2.313,2.708 2.604,2.958 0.292,0.25 18 true iv

i.

Disconnect the connector.


ii.

Disengage the clamp to separate the wire harness from the brake actuator bracket assembly.


iii.

Disengage the clamp to separate the wire harness from the brake actuator bracket assembly.


iv.

Remove the bolt, 2 nuts and brake actuator with brake booster pump assembly from the vehicle body.

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake booster pump assembly by the connector, union or wire harness.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with brake booster pump assembly when carrying it.



HINT:

Remove the brake actuator with brake booster pump assembly while avoiding the brake lines.




Hide 44571A 9.REMOVE NO. 1 BRAKE ACTUATOR HOSE

a.
C430267


Hide 47381 10.REMOVE NO. 1 BRAKE TUBE CLAMP BRACKET

a.
C430269


Hide 44521B 11.REMOVE NO. 2 BRAKE ACTUATOR CASE COLLAR

a.
C430274


Hide 47999A 12.REMOVE BRAKE TRACTION ACTUATOR BRACKET BUSH

a.
C430403


Hide 47070 13.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

a.
C430404

NOTICE:
·
C430273C03
0.531,1.708 0.865,1.708 false 0.448,1.281 0.781,1.281 false 1.698,1.719 2.083,1.167 2.083,1.167 2.25,1.167 true 2.531,1.844 2.74,1.479 2.74,1.479 2.906,1.479 true 0.344,1.635 0.656,1.833 0.313,0.198 10 false *a 0.25,1.208 0.563,1.406 0.313,0.198 10 false *b 2.292,1.104 2.604,1.302 0.313,0.198 10 false *c 2.938,1.406 3.25,1.604 0.313,0.198 10 false *d
*a Union
*b Connector
*c Wire Harness
*d Stud


Do not carry the brake booster pump assembly by the parts shown in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.