Home › Brake › BRAKE SYSTEM (OTHER) › VACUUM PUMP (for BOSCH Made) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480872 VACUUM PUMP(for BOSCH Made) A

BRAKE SYSTEM (OTHER)  VACUUM PUMP(for BOSCH Made)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C442531N02
1.51,0.833 2.167,1 0.656,0.167 1.469,0.792 2.208,1.031 0.74,0.24 6.219,2.031 6.885,2.208 0.667,0.177 4.969,2.781 5.635,2.958 0.667,0.177 5.5,5.385 6.156,5.552 0.656,0.167 5.458,5.354 6.198,5.594 0.74,0.24 4.49,4.146 4.792,4.146 false 4.646,5.021 5.021,5.021 false 6.167,3.583 6.5,3.583 false 5.208,1.375 5.542,1.375 false 1.385,1.281 1.719,1.281 false 3.604,4.823 3.604,5.156 false 6.573,0.156 6.906,0.156 false 2.167,0.917 2.333,0.917 2.333,0.917 2.542,1.156 false 4.635,2.865 4.969,2.865 false 5.885,2.115 6.219,2.115 false 5.167,5.469 5.5,5.469 false 3.563,5.156 3.719,5.354 0.156,0.198 10 false ● 5.063,5.521 5.302,5.719 0.24,0.198 10 false x3 5.313,4.875 5.552,5.24 0.24,0.365 18 false 1 5.073,4.021 5.313,4.385 0.24,0.365 18 false 4 6.552,3.438 6.792,3.802 0.24,0.365 18 false 3 4.594,2.927 4.833,3.125 0.24,0.198 10 false x4 5.594,1.24 5.833,1.604 0.24,0.365 18 false 2 1.76,1.146 2,1.51 0.24,0.365 18 false 5 6.365,0 6.604,0.365 0.24,0.365 18 false 6 6.26,2.042 6.896,2.208 0.635,0.167 8 false 10 (102, 7) 5.01,2.792 5.646,2.958 0.635,0.167 8 false 10 (102, 7) 1.573,0.833 2.208,1 0.635,0.167 8 false 10 (102, 7) 5.531,5.396 6.167,5.563 0.635,0.167 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 VACUUM PUMP ASSEMBLY 29300 (Click here) - -
2 ENGINE WIRE 82121 - - -
3 FUEL TANK TO CANISTER TUBE 77261D - - -
4 NO. 1 VACUUM HOSE CONNECTOR 44777 (Click here) - -
5 ECM 89661 - - -
6 VACUUM PUMP OPERATION - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

Refer to the following illustration and check which type is installed to the vehicle.

C449630C01
2.167,3.25 2,3.25 2,3.25 1.479,1.594 true 0.25,0.427 0.625,0.667 0.375,0.24 12 false *A 3.667,0.427 4.042,0.667 0.375,0.24 12 false *B 2.219,3.167 2.531,3.365 0.313,0.198 10 false *a
*A for BOSCH Made *B except BOSCH Made
*a Mark - -



PROCEDURE

Hide 29300 1.INSTALL VACUUM PUMP ASSEMBLY

a.
C442532C01
1.656,2.656 1.75,2.25 1.75,2.25 1.917,2.25 true 1.885,3.417 2.052,3.417 2.052,3.417 2.25,3 true 3.885,0.583 4.135,0.854 0.25,0.271 18 true i 0.573,1.938 0.833,2.188 0.26,0.25 18 true ii 4.031,1.948 4.292,2.198 0.26,0.25 18 true iii 1.917,2.156 2.146,2.354 0.229,0.198 10 true *b 1.635,3.313 1.865,3.51 0.229,0.198 10 true *a
*a Coupling Teeth *b Groove


i.

When reusing the vacuum pump assembly:

Install a new No. 1 vacuum pump O-ring to the vacuum pump assembly.


ii.

Install the vacuum pump assembly so that the coupling teeth of the vacuum pump assembly and groove of the camshaft are engaged.

NOTICE:
·

Ensure that the vacuum pump assembly is installed securely.

·

Be careful not to pinch the No. 1 vacuum pump O-ring.




iii.

Using an 8 mm socket wrench, install the vacuum pump assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

After installation, check that there are no gaps between the matching surfaces and that the vacuum pump assembly is not installed at an angle.




Hide 82121 2.INSTALL ENGINE WIRE

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 77261D 3.INSTALL FUEL TANK TO CANISTER TUBE

Hide 44777 4.CONNECT NO. 1 VACUUM HOSE CONNECTOR

Z101186

NOTICE:
·

Check that there is no foreign matter on the connecting parts.

·

After connecting the No. 1 vacuum hose connector, check that the vacuum pump assembly and No. 1 vacuum hose connector are securely connected by pulling on them.




a.
C442533N01
0.333,0.01 0.615,0.365 0.281,0.354 18 false i

i.

Align the No. 1 vacuum hose connector with the vacuum pump assembly, and push them together until the No. 1 vacuum hose connector makes a "click" sound.