|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| *A | for Manual Transaxle | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | * | For use with a union nut wrench |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 12 | DASH PANEL HEAT INSULATOR | 55225C | - | - | - |
| 13 | NO. 1 ENGINE UNDER COVER ASSEMBLY | 51410 | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *A | for TMC Made | *B | for TMMF Made |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
|
Lithium soap base glycol grease | - | - |
44785
1.INSTALL BRAKE BOOSTER GASKET
44610
2.TEMPORARILY INSTALL BRAKE BOOSTER ASSEMBLY
Do not apply excessive force to the brake lines or refrigerant lines.
Temporarily install the brake booster assembly to the vehicle.
Return the front No. 1 brake tube and front No. 2 brake tube to their original positions.
3.TEMPORARILY INSTALL CLEVIS LOCK NUT
|
|
47264D
4.TEMPORARILY INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
|
|
44610
5.INSTALL BRAKE BOOSTER ASSEMBLY
|
Protective Tape | - | - |
Install the 4 nuts to secure the brake booster assembly.
Tighten the 4 nuts in the order shown in the illustration.
Remove the protective tape.
Connect the connector.
6.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE
| *a | Paint Mark | - | - |
Connect the check valve to connector tube hose to the brake booster assembly and slide the clip to secure it.
When connecting the check valve to connector tube hose, face the paint mark up.
Make sure that the tabs of the clip are facing upward.
47371A
7.INSTALL NO. 1 BRAKE TUBE CLAMP
47372
8.INSTALL NO. 2 BRAKE TUBE CLAMP
31481
9.INSTALL CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE (for Manual Transaxle)
47374B
10.INSTALL NO. 4 BRAKE TUBE CLAMP
11.INSTALL BRAKE LINE
| *a | Torque Wrench Fulcrum Length | - | - |
Temporarily install front No. 1 brake tube and front No. 2 brake tube to the correct position on the brake actuator assembly.
Using a 12 mm union nut wrench, tighten the front No. 1 brake tube and front No. 2 brake tube.
Do not kink or damage the brake lines.
Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)
55225C
12.INSTALL DASH PANEL HEAT INSULATOR
51410
13.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
55606
17.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
18.INSTALL BATTERY
47201
19.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
for TMC Made:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER (for Gasoline Model TMC Made RHD)>INSTALLATION
for TMMF Made:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER (for Gasoline Model TMMF Made RHD)>INSTALLATION
20.INSPECT AND ADJUST BRAKE PEDAL