| *1 | FRONT FLEXIBLE HOSE | - | - |
| *A | for TMC Made | *B | for TMMF Made |
| *1 | FRONT SHOCK ABSORBER ASSEMBLY | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front shock absorber assembly removal/installation are shown below.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1.REMOVE FRONT WHEEL
48810
2.SEPARATE FRONT STABILIZER LINK ASSEMBLY
|
|
Remove the nut to separate the front stabilizer link assembly from the front shock absorber with coil spring.
89543
3.SEPARATE FRONT SPEED SENSOR
48684B
4.REMOVE FRONT SUSPENSION SUPPORT DUST COVER
5.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING
| *a | Wooden Block | *b | Jack |
Support the front lower No. 1 suspension arm sub-assembly using a jack and wooden block.
Keep the front lower No. 1 suspension arm sub-assembly supported until installation of the front shock absorber with coil spring is complete.
Remove the 2 bolts and 2 nuts, to separate the front shock absorber with coil spring from the steering knuckle.
When removing the nuts, keep the bolts from rotating.
Use wire or an equivalent tool to hang the separated steering knuckle.
Using SST, fix the front shock absorber rod and remove the nut.
Remove the front shock absorber with coil spring from the vehicle.
48682B
6.REMOVE FRONT NO. 2 SUSPENSION SUPPORT
48609E
7.REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT
Secure SST in a vise.
Attach the hooks of each SST arm across the diameter of the front coil spring.
| *a | Front Coil Spring Diameter |
Do not perform the work without checking to make sure that the claws of the hooks are securely engaged.
It could cause the hook to slip off and the spring to fly out, which could result in an injury.
Do not install SST to the front coil spring unless its top and bottom hook distance is set to the widest condition.
It could cause the hook to slip off and the spring to fly out, which could result in an injury.
Do not install SST when the distances between the SST arms or the number of coils of the coil spring between the hooks are not the same.
It could cause the hook to slip off and the spring to fly out, which could result in an injury.
| *a | Stopper Pins | - | - |
Install the stopper pins to the hooks of SST.
Do not perform the work if the stopper pin is not securely installed.
It could cause the hook to slip off and the spring to fly out, which could result in an injury.
Using SST, compress the front coil spring.
While compressing the spring, if the front coil spring starts to bend into a bow shape, do not continue the work.
It could cause the hook to slip off and the spring to fly out, which could result in an injury.
Do not compress the springs so far that the coils of the springs touch each other.
It could cause the hook to slip off and the spring to fly out, which could result in an injury.
Do not use an impact wrench.
The threads may be stripped, or the sudden compression may result in slack that causes the hooks to slip off, causing the spring to fly out and possibly resulting in injury.
If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.
If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.
If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
Check that the front coil spring has become free, and using SST and a 6 mm hexagon socket wrench, remove the front support to front shock absorber nut.
If the front coil spring has not become free, do not remove the front support to front shock absorber nut.
The spring force will cause the components to be scattered, possibly resulting in injury.
48609
8.REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY
48619A
9.REMOVE STRUT MOUNTING BEARING
48471C
10.REMOVE FRONT UPPER COIL SPRING SEAT
48559B
11.REMOVE FRONT NO. 1 SHOCK ABSORBER DUST COVER
| *a | Claw | *b | Front No. 1 Shock Absorber Dust Cover |
Disengage the end of the front No. 1 shock absorber dust cover from the claws of the front shock absorber assembly.
Remove the front No. 1 shock absorber dust cover with front upper coil spring insulator from the front shock absorber assembly.
48157C
12.REMOVE FRONT UPPER COIL SPRING INSULATOR
48132
13.REMOVE FRONT COIL SPRING
|
|
Remove the front coil spring and SST.
48331C
14.REMOVE FRONT SPRING BUMPER
48158C
15.REMOVE FRONT LOWER COIL SPRING INSULATOR
| *A | for TMC Made | *B | for TMMF Made |