Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for LED Headlight) › from 2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0440190 HEADLIGHT ASSEMBLY(for LED Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for LED Headlight)  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
E460588N01
3.125,2.5 5.333,3.698 2.208,1.198 3.521,0.26 3.854,0.26 false 4.292,3.188 4.625,3.188 false 3.948,2.771 4.281,2.771 false 4.927,3.073 5.208,3.427 0.281,0.354 18 false 1 4.74,2.615 5.021,2.969 0.281,0.354 18 false 2 3.896,0.125 4.177,0.479 0.281,0.354 18 false 3 4.583,2.667 4.865,2.896 0.281,0.229 10 false ● 3.656,3.49 3.948,3.677 0.292,0.188 10 false x3 3.167,2.542 3.448,2.771 0.281,0.229 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HEADLIGHT ECU SUB-ASSEMBLY 81056 (Click here) - -
2 HEADLIGHT GASKET 81134 (Click here) - -
3 NO. 1 HEADLIGHT COVER 81144 - - -

*A w/ Adaptive High Beam System - -
● Non-reusable part - -

E460581N01
0.083,0.042 1.823,1.25 1.74,1.208 0.417,1.417 2.167,2.833 1.75,1.417 4.563,3.333 7.063,5.75 2.5,2.417 5.333,0.219 7.083,2.917 1.75,2.698 5.417,0.427 7,2.833 1.583,2.406 4.573,4.542 7.052,4.542 false 1.573,3.458 1.938,3.458 false 2.844,4.979 2.885,5.146 2.885,5.146 3.052,5.146 false 0.833,1.125 1,1.125 1,1.125 1.042,0.875 false 1.177,1.792 1.427,1.792 false 4.302,1.667 4.385,1.917 4.385,1.917 4.552,1.917 false 0.417,2.167 2.167,2.167 false 5.333,3.844 5.5,3.844 false 5.354,5.042 5.521,5.042 false 1.229,2.49 1.563,2.49 false 0.417,0.823 0.583,0.823 0.583,0.823 0.865,0.448 false 5.969,1.104 5.969,0.771 false 6.521,1.125 6.521,0.792 false 5.417,1.583 7,1.583 false 5.99,2.49 5.99,2.156 false 6.552,2.448 6.552,2.115 false 3.885,4.333 4.073,4.5 0.188,0.167 10 false x7 1.385,3.313 1.583,3.594 0.198,0.281 18 false 7 1.25,3.385 1.427,3.563 0.177,0.177 10 false ● 0.531,0.948 0.896,1.229 0.365,0.281 18 false 14 1.01,1.635 1.208,1.917 0.198,0.281 18 false 8 3.323,5.031 3.521,5.313 0.198,0.281 18 false 6 1.021,2.313 1.219,2.594 0.198,0.281 18 false 9 4.615,1.823 4.885,2.083 0.271,0.26 10 false *1 5.073,4.906 5.396,5.177 0.323,0.271 18 false 11 5.052,3.719 5.375,3.99 0.323,0.271 18 false 10 4.635,3.385 4.958,3.656 0.323,0.271 12 false *A 4.635,4.594 4.958,4.865 0.323,0.271 12 false *B 0.458,1.458 0.781,1.729 0.323,0.271 12 false *A 0.458,2.198 0.781,2.469 0.323,0.271 12 false *B 1.375,1.948 1.563,2.115 0.188,0.167 10 false x2 1.365,1.052 1.552,1.219 0.188,0.167 10 false x2 0.385,0.458 0.573,0.625 0.188,0.167 10 false x2 0.25,0.719 0.458,0.906 0.208,0.188 10 false *2 0.125,0.063 0.448,0.333 0.323,0.271 12 false *A 5.948,1.177 6.104,1.375 0.156,0.198 10 false ● 6.042,1.135 6.594,1.49 0.552,0.354 18 false 5 6.573,1.135 6.969,1.49 0.396,0.354 18 false 4 5.365,0.219 5.74,0.458 0.375,0.24 12 false *B 5.438,0.458 5.802,0.75 0.365,0.292 12 false *C 5.458,1.615 5.833,1.854 0.375,0.24 12 false *D 5.948,2.521 6.104,2.719 0.156,0.198 10 false ● 6.052,2.5 6.385,2.833 0.333,0.333 18 false 13 6.427,2.469 6.813,2.771 0.385,0.302 18 false 12

Procedure Part Name Code
Z101186

Z101188

Z101187

4 HEADLIGHT LEVELING MOTOR 85662 (Click here) - -
5 HEADLIGHT LEVELING MOTOR BASE PACKING 85669 (Click here) - -
6 HEADLIGHT LENS SUB-ASSEMBLY 8110B (Click here) - -
7 HEADLIGHT LENS GASKET 81132B (Click here) - -
8 LIGHT CONTROL LED ECU 85967D (Click here) - -
9 LIGHT CONTROL LED ECU 85967D (Click here) - -
10 HEADLIGHT UNIT 81171A (Click here) - -
11 HEADLIGHT UNIT 81171A (Click here) - -
12 HEADLIGHT LEVELING MOTOR 85662 - - -
13 HEADLIGHT LEVELING MOTOR BASE PACKING 85669 (Click here) - -
14 HEADLIGHT LEVELING MOTOR 85662 - - -

*A w/ Adaptive High Beam System *B w/o Adaptive High Beam System
*C for TMC Made *D for TMMF Made
*1 HEADLIGHT HOUSING SUB-ASSEMBLY *2 HEADLIGHT BRACKET
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>PRECAUTION

·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81056A 1.REMOVE HEADLIGHT ECU SUB-ASSEMBLY (w/ Adaptive High Beam System)

Z101186

Click here(Click here)

Hide 81134 2.REMOVE HEADLIGHT GASKET (w/ Adaptive High Beam System)

Z101186

Click here(Click here)

Hide 81144 3.REMOVE NO. 1 HEADLIGHT COVER

a.
E448007C02
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 85662 4.REMOVE HEADLIGHT LEVELING MOTOR (w/o Adaptive High Beam System)

a.

for TMC Made:

E448005C03
0.375,0.031 0.656,0.385 0.281,0.354 18 false i 3.656,0.031 3.938,0.385 0.281,0.354 18 false ii
V100135

Turn
V113147

Remove in this Direction


i.

Turn the aiming screws as shown in the illustration until the aiming screws are disconnected from the headlight unit.

NOTICE:

Make sure to remember the number of aiming screw rotations.



ii.

Remove the headlight leveling motor as shown in the illustration.



Hide 85669 5.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING (w/o Adaptive High Beam System)

Z101186

NOTICE:

The headlight leveling motor base packing must not be reused.



a.

for TMC Made:

E448006


Hide 8110B 6.REMOVE HEADLIGHT LENS SUB-ASSEMBLY

a.
E460589C01
0.354,0.094 0.635,0.448 0.281,0.354 18 false i 0.344,1.979 0.625,2.333 0.281,0.354 18 false iv 6.677,0.083 6.958,0.438 0.281,0.354 18 false ii 4.063,1.938 4.344,2.292 0.281,0.354 18 false v 6.844,0.417 7.156,0.615 0.313,0.198 10 false *a 4.167,0.292 5,0.646 0.833,0.354 18 false iii
*a "TORX" Screw - -


i.

Disconnect the connector.

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)


ii.

Using a T20H "TORX" driver, remove the "TORX" screw.


iii.

Remove the 7 screws.


iv.

Using a hair dryer, heat the backside of the headlight assembly.

NOTICE:
·

Do not heat the backside of the headlight lens sub-assembly above 120 °C (248 °F).

·

If the headlight assembly is heated unevenly, it will deform or melt.




v.

Disengage the claws to remove the headlight lens sub-assembly.

NOTICE:

If the headlight lens sub-assembly cannot be separated even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens sub-assembly. Be careful not to damage the headlight lens sub-assembly and headlight housing sub-assembly.




Hide 81132B 7.REMOVE HEADLIGHT LENS GASKET

Z101186

NOTICE:

Make sure to replace the headlight lens gasket with a new one. Failure to do so may cause water ingress.



a.
E448010


Hide 85967D 8.REMOVE LIGHT CONTROL LED ECU (w/ Adaptive High Beam System)

Z101186

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E460516


Hide 85967D 9.REMOVE LIGHT CONTROL LED ECU (w/o Adaptive High Beam System)

Z101186

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E448014


Hide 81171A 10.REMOVE HEADLIGHT UNIT (w/ Adaptive High Beam System)

Z101186

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E460517C01
0.146,0.042 0.708,0.365 0.563,0.323 18 false i, ii 4.021,0.094 4.302,0.385 0.281,0.292 18 false iii 1.917,1.979 2.198,2.271 0.281,0.292 18 false iv
V100135

Turn
V113147

Remove in this Direction


i.

Disconnect the 2 connectors.


ii.

Disengage the clip and clamp.


iii.

While holding the headlight unit by hand, turn the 2 aiming screws as shown in the illustration until the 2 aiming screws are disconnected from the headlight unit.

NOTICE:

Make sure to remember the number of aiming screw rotations.



iv.

Remove the headlight unit from the headlight housing sub-assembly as shown in the illustration.



Hide 81171A 11.REMOVE HEADLIGHT UNIT (w/o Adaptive High Beam System)

Z101186

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E460518C01
0.396,0.125 0.958,0.448 0.563,0.323 18 false i, ii 0.375,1.979 0.656,2.271 0.281,0.292 18 false iii 3.927,1.969 4.208,2.26 0.281,0.292 18 false iv 0.135,0.167 0.51,0.406 0.375,0.24 12 false *A 3.885,0.146 4.26,0.385 0.375,0.24 12 false *B 4.198,0.104 5.573,0.458 1.375,0.354 18 false i, ii
*A for TMC Made *B for TMMF Made
V100135

Turn
V113147

Remove in this Direction


i.

Disconnect the connector.


ii.

Disengage the claws and clamp.


iii.

While holding the headlight unit by hand, turn the aiming screw as shown in the illustration until the aiming screw are disconnected from the headlight unit.

NOTICE:

Make sure to remember the number of aiming screw rotations.



iv.

Remove the headlight unit from the headlight housing sub-assembly as shown in the illustration.



Hide 85662 12.REMOVE HEADLIGHT LEVELING MOTOR (w/o Adaptive High Beam System)

a.

for TMMF Made:

E460491C02
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 85669 13.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING (w/o Adaptive High Beam System)

Z101186

NOTICE:

The headlight leveling motor base packing must not be reused.



a.

for TMMF Made:

E460579


Hide 85662 14.REMOVE HEADLIGHT LEVELING MOTOR (w/ Adaptive High Beam System)

a.
E448019